ROOF HEADLINING (for Sedan) INSTALLATION


  1. INSTALL REAR NO. 2 SIDE RAIL SPACER LH

    A010OIL

    1. Attach the 2 claws to install the No. 2 side rail spacer.

  2. INSTALL REAR NO. 2 SIDE RAIL SPACER RH

    Tech Tips

    Use the same procedure described for the LH side.

  3. INSTALL FRONT SHOULDER BELT ANCHOR PLATE SUB-ASSEMBLY LH

    A010QFA

    1. Attach the 5 claws to install the front shoulder belt anchor plate.

  4. INSTALL FRONT SHOULDER BELT ANCHOR PLATE SUB-ASSEMBLY RH

    Tech Tips

    Use the same procedure described for the LH side.

  5. INSTALL REAR DOOR SCUFF PLATE OUTSIDE LH

    A010RXD

    1. Attach the 2 clips to install the rear door scuff plate outside.

  6. INSTALL REAR DOOR SCUFF PLATE OUTSIDE RH

    Tech Tips

    Use the same procedure described for the LH side.

  7. INSTALL FRONT DOOR SCUFF PLATE OUTSIDE LH

    A010PL8

    1. Attach the 3 clips to install the front door scuff plate outside.

  8. INSTALL FRONT DOOR SCUFF PLATE OUTSIDE RH

    Tech Tips

    Use the same procedure described for the LH side.

  9. INSTALL ROOF HEADLINING ASSEMBLY

    A010PTFE01

    1. Place the roof headlining into the vehicle through the passenger door.

      Note

      Be careful not to damage the roof headlining when placing it in the cabin.

    2. Attach the clip to install the roof headlining.

      A010QOM

    3. for LHD:


      1. A010R78E01

        Connect the 2 roof wire connectors.

      2. A010OEJE01

        Connect the 2 clamps.

    4. for RHD:


      1. A010ONUE01

        Connect the roof wire connector.

      2. A010RVDE01

        Connect the 2 clamps and connector.

    5. A010S9C

      Connect the 4 clamps to the front pillar LH.

    6. w/ Digital Audio Broadcasting Antenna:

      Attach the wire harness clamp and connect the connector to the rear pillar LH.

    7. A010O28

      Install the antenna with the 2 bolts.

      Torque:
      7.0 N*m  { 71 kgf*cm, 62 in.*lbf }

    8. Connect the clamp to the rear pillar RH.

    9. Connect the 3 connectors.

    10. A010QFZ

      Connect the 3 clamps to the front pillar RH.

    11. Connect the connector.

    12. A010SAB

      w/ Lane Keeping Assist System:

      Tech Tips


      • Use the same procedure for RHD and LHD vehicles.

      • The procedure listed below is for LHD vehicles.


      1. Connect the connector and attach the clamp.

    13. A010NAJ

      w/ Rain Sensor:

      Connect the rain sensor connector.

    14. A010PXI

      w/ EC Mirror:

      Connect the EC mirror connector.

  10. INSTALL SUNSHADE TRIM HOLDER

    A010RSSE01

    1. Position the pin as shown in the illustration and install the sunshade trim holder.

  11. INSTALL ASSIST GRIP SUB-ASSEMBLY

    A010SFE

    Tech Tips

    Use the same procedure for the other assist grip.


    1. Assemble the assist grip as shown in the illustration.

    2. A010S5E

      Install the assist grip.

  12. INSTALL REAR ASSIST GRIP ASSEMBLY LH

    A010OPQ

    1. Assemble the rear assist grip as shown in the illustration.

    2. A010OAR

      Install the rear assist grip.

  13. INSTALL REAR ASSIST GRIP ASSEMBLY RH

    Tech Tips

    Use the same procedure described for the LH side.

  14. INSTALL VISOR HOLDER

    A010S1Z

    Tech Tips

    Use the same procedure to install the visor holder on the other side.


    1. Attach the 2 claws.

    2. Push in the visor holder as shown in the illustration.

  15. INSTALL VISOR ASSEMBLY LH

    A010OKB

    1. Attach the 2 clips to install the visor.

  16. INSTALL VISOR ASSEMBLY RH

    Tech Tips

    Use the same procedure described for the LH side.

  17. INSTALL RAIN SENSOR COVER (w/ Rain Sensor)


    1. Clean the surface of the windshield glass that contacts the rain sensor.

    2. When replacing the rain sensor with a new one:

      Remove the protective cover on the rain sensor.

      Note

      Do not touch the silicon mixture directly with a finger.

    3. A006T6J

      Connect the connector.

      Note

      Do not touch the silicon mixture directly with a finger.

    4. A006W64

      Attach the 2 claws to install the rain sensor.

      Note

      Make sure that there are no air bubbles between the silicon mixture and windshield glass.

  18. INSTALL INNER REAR VIEW MIRROR STAY HOLDER COVER (w/ EC Mirror)


    1. w/o Rear Monitor:

      Install the inner rear view mirror stay holder cover Click here.

    2. w/ Rear Monitor:

      Install the inner rear view mirror stay holder cover Click here.

  19. INSTALL NO. 1 ROOM LIGHT ASSEMBLY

    A010RUF

    1. Connect the connector.

    2. Attach the 4 clips to install the No. 1 room light.

  20. INSTALL FRONT ROOF TOP GARNISH (w/ Lane Keeping Assist System)


    1. Attach the 2 claws and clip to install the front roof top garnish.

      A00EAPCE01

      Note

      When removing the rain sensor cover, do not apply force to the lane recognition camera sensor assembly areas labeled "X".

  21. INSTALL MAP LIGHT ASSEMBLY

    A010R29

    1. Connect the connector.

    2. Attach the 4 clips to install the map light.

  22. INSTALL LOWER INSTRUMENT PANEL SUB-ASSEMBLY

    Tech Tips


    • Use the same procedure for RHD and LHD vehicles.

    • The procedure listed below is for LHD vehicles.


    1. Install the lower instrument panel sub-assembly Click here.

  23. INSTALL CONSOLE BOX ASSEMBLY


    1. Install the console box assembly Click here.

  24. INSTALL UPPER INSTRUMENT PANEL SUB-ASSEMBLY

    Tech Tips


    • Use the same procedure for RHD and LHD vehicles.

    • The procedure listed below the for LHD vehicles.


    1. Install the upper instrument panel sub-assembly Click here.

  25. INSTALL INNER ROOF SIDE GARNISH LH

    A010SAYE01
    Text in Illustration
    *1 Clip A

    1. Install 2 new clips labeled A to the inner roof side garnish.

    2. Attach the 5 clips to install the inner roof side garnish.

  26. INSTALL INNER ROOF SIDE GARNISH RH

    Tech Tips

    Use the same procedure described for the LH side.

  27. INSTALL CENTER PILLAR GARNISH LH

    A010OB6

    1. Pass the front seat outer belt floor anchor through the center pillar garnish.

    2. Attach the clip to install the center pillar garnish.

    3. Install the 2 screws.

    4. A010RTF

      Install the front seat outer belt floor anchor with the bolt.

      Torque:
      41 N*m  { 418 kgf*cm, 30 ft.*lbf }

  28. INSTALL CENTER PILLAR GARNISH RH

    Tech Tips

    Use the same procedure described for the LH side.

  29. INSTALL LAP BELT OUTER ANCHOR COVER

    A010NB4

    Tech Tips

    Use the same procedure for the other lap belt outer anchor cover.


    1. Attach the 3 claws to install the lap belt outer anchor cover.

  30. INSTALL LOWER CENTER PILLAR GARNISH LH

    A010OHA

    1. Attach the 2 claws and 3 clips to install the lower center pillar garnish.

  31. INSTALL LOWER CENTER PILLAR GARNISH RH

    Tech Tips

    Use the same procedure described for the LH side.

  32. INSTALL FRONT PILLAR GARNISH LH

    A010NRNE01
    Text in Illustration
    *1 Front Pillar Garnish Clip
    *2 Protective Tape

    1. w/ Curtain Shield Airbag:

      Remove the protective cover.

    2. Attach the 2 guides.

    3. Turn the end of the front pillar garnish clip 90° with needle-nose pliers and install it to the front pillar garnish.

      Tech Tips

      Tape the tips of the needle-nose pliers before use.

    4. A010OEDE01
      Text in Illustration
      *1 Front Pillar Garnish Clip

      Attach the 2 clips to install the front pillar garnish.

  33. INSTALL FRONT PILLAR GARNISH RH

    Tech Tips

    Use the same procedure described for the LH side.

  34. INSTALL REAR DOOR OPENING TRIM WEATHERSTRIP LH

    A010NY1E01
    Text in Illustration
    *1 Paint Mark
    *2 Mark Position

    1. Install the rear door opening trim weatherstrip as shown in the illustration.

  35. INSTALL REAR DOOR OPENING TRIM WEATHERSTRIP RH

    Tech Tips

    Use the same procedure described for the LH side.

  36. INSTALL REAR DOOR SCUFF PLATE LH

    A010S97

    1. Attach the clip and 6 claws to install the front door scuff plate.

  37. INSTALL REAR DOOR SCUFF PLATE RH

    Tech Tips

    Use the same procedure described for the LH side.

  38. INSTALL FRONT DOOR OPENING TRIM WEATHERSTRIP LH

    A010Q9ME01
    Text in Illustration
    *1 Paint Mark
    *2 Mark Position

    1. Install the front door opening trim weatherstrip as shown in the illustration.

  39. INSTALL FRONT DOOR OPENING TRIM WEATHERSTRIP RH

    Tech Tips

    Use the same procedure described for the LH side.

  40. INSTALL COWL SIDE TRIM BOARD LH

    A010NBR

    1. Attach the clip, claw and guide to install the cowl side trim board.

  41. INSTALL COWL SIDE TRIM BOARD RH

    Tech Tips

    Use the same procedure described for the LH side.

  42. INSTALL FRONT DOOR SCUFF PLATE LH

    A010S4G

    1. Attach the 2 clips and 8 claws to install the front door scuff plate.

  43. INSTALL FRONT DOOR SCUFF PLATE RH

    Tech Tips

    Use the same procedure described for the LH side.

  44. INSTALL REAR SIDE SEATBACK ASSEMBLY LH


    1. A003BE1E01

      Install the claw as shown in the illustration.

    2. Install the side seatback with the bolt.

      Torque:
      7.8 N*m  { 80 kgf*cm, 69 in.*lbf }
    3. A003CVN

      Install the rear seat 3 point type belt anchor with the bolt.

      Torque:
      41 N*m  { 418 kgf*cm, 30 ft.*lbf }

      Note

      Do not allow the anchor part of the rear seat 3 point type belt to overlap the protruding parts of the floor panel.

    4. Install the seat belt to the belt guide.

    5. Attach the claw to close the cap of the rear seat shoulder belt guide.

    6. Check if the ELR locks.

      Note

      The check should be performed with the outer belt assembly installed.


      1. With the belt assembly installed, check that the belt locks when it is pulled out quickly.

  45. INSTALL REAR SIDE SEATBACK ASSEMBLY RH

    Tech Tips

    Use the same procedure described for the LH side.

  46. INSTALL BENCH TYPE REAR SEAT CUSHION ASSEMBLY

    A003CGQE01

    1. Attach the 2 rear hooks of the seat cushion to the seatback.

    2. Attach the 2 front hooks to install the seat cushion.

    3. Confirm that the seat cushion is firmly installed.

      Note

      When installing the seat cushion, make sure the seat belt buckle is not under the seat cushion.

  47. INSTALL FRONT SEAT ASSEMBLY LH


    1. for Manual Seat:

      Install the front seat assembly Click here.

    2. for Power Seat:

      Install the front seat assembly Click here.

  48. INSTALL FRONT SEAT ASSEMBLY RH

    Tech Tips

    Use the same procedure described for the LH side.

  49. CONNECT CABLE TO NEGATIVE BATTERY TERMINAL

    Note

    When disconnecting the cable, some systems need to be initialized after the cable is reconnected Click here.