UPPER INSTRUMENT PANEL INSTALLATION

Tech Tips


  • Use the same procedure for RHD and LHD vehicles.

  • The procedure listed below is for LHD vehicles.

  • A bolt without a torque specification is shown in the standard bolt chart Click here.


  1. INSTALL GLOVE COMPARTMENT DOOR LOCK CYLINDER ASSEMBLY

    A00OTB7

    1. Insert the bottom side of the glove compartment door lock cylinder as shown in the illustration, hold down the stopper and install the glove compartment door lock cylinder.

  2. INSTALL UPPER INSTRUMENT PANEL SUB-ASSEMBLY


    1. Securely attach the 6 claws and 4 clips of the instrument panel to the vehicle body.

    2. Install the instrument panel with the 3 screws <C>.

      A00OTL7

    3. Install the passenger airbag bolt <A>.

      Torque:
      20 N*m  { 204 kgf*cm, 15 ft.*lbf }

    4. Connect the connectors and clamp.

      A00OV0ZE01
    5. A00OV9I

      When replacing the upper instrument panel sub-assembly with a new one:


      1. Twist the rib (the piece used to maintain the shape of the panel) in the direction of the arrow in the illustration until it detaches from the instrument panel, and remove the rib.

  3. INSTALL NO. 2 INSTRUMENT PANEL SPEAKER PANEL SUB-ASSEMBLY (for 11 Speakers)


    1. A00OU1E

      Attach the 2 clips and 3 claws to install the speaker panel.

  4. INSTALL NO. 2 INSTRUMENT PANEL SPEAKER PANEL SUB-ASSEMBLY


    1. A00OV5M

      Connect the speaker connector.

    2. A00OVLC

      Set the 2 claws on the side of the speaker panel towards the front of the vehicle in place and using them as pivot points, lower the panel in the direction indicated by the arrow in the illustration, and then attach the claws and clips to the instrument panel to install the speaker panel.

  5. INSTALL NO. 1 INSTRUMENT PANEL SPEAKER PANEL SUB-ASSEMBLY (for 11 Speakers)

    Tech Tips

    Use the same procedure described for the No. 2 instrument panel speaker panel.

  6. INSTALL NO. 1 INSTRUMENT PANEL SPEAKER PANEL SUB-ASSEMBLY

    Tech Tips

    Use the same procedure described for the No. 2 instrument panel speaker panel.

  7. INSTALL FRONT PILLAR GARNISH LH (for Sedan)

    A010NRNE01
    Text in Illustration
    *1 Front Pillar Garnish Clip
    *2 Protective Tape

    1. w/ Curtain Shield Airbag:

      Remove the protective cover.

    2. Attach the 2 guides.

    3. Turn the end of the front pillar garnish clip 90° with needle-nose pliers and install it to the front pillar garnish.

      Tech Tips

      Tape the tips of the needle-nose pliers before use.

    4. A010OEDE01
      Text in Illustration
      *1 Front Pillar Garnish Clip

      Attach the 2 clips to install the front pillar garnish.

  8. INSTALL FRONT PILLAR GARNISH LH (for Wagon)

    A00OUUXE01
    Text in Illustration
    *1 Front Pillar Garnish Clip
    *2 Protective Tape

    1. Remove the protective cover.

    2. Attach the 2 guides.

    3. Turn the end of the front pillar garnish clip 90° with needle-nose pliers and install it to the front pillar garnish.

      Tech Tips

      Tape the tips of the needle-nose pliers before use.

    4. A00OU3LE01
      Text in Illustration
      *1 Front Pillar Garnish Clip

      Attach the 2 clips to install the front pillar garnish.

  9. INSTALL FRONT PILLAR GARNISH RH (for Sedan)

    Tech Tips

    Use the same procedure described for the LH side.

  10. INSTALL FRONT PILLAR GARNISH RH (for Wagon)

    Tech Tips

    Use the same procedure described for the LH side.

  11. INSTALL INSTRUMENT SIDE PANEL LH


    1. A00OS50

      Attach the 2 hooks.

    2. A00OV5V

      Attach the 3 clips and 4 claws to install the side panel.

  12. INSTALL INSTRUMENT SIDE PANEL RH


    1. A00OTT8E01
      Text in Illustration
      *1 w/ Airbag Cut Off Switch Cylinder

      Attach the 2 hooks.

    2. w/ Airbag Cut Off Switch Cylinder:


      1. Connect the connector.

    3. A00OUWP

      Attach the 3 clips and 4 claws to install the side panel.

  13. INSTALL CENTER INSTRUMENT PANEL REGISTER ASSEMBLY WITH FINISH PANEL (w/ Audio)


    1. A00OVXQ

      Connect the connector and clamp.

    2. A00OU39

      Attach the 2 clips and hook.

    3. A00OQOK

      Attach the 2 clips.

    4. Attach the 3 claws and 3 hooks to install the panel register.

  14. INSTALL CENTER INSTRUMENT PANEL REGISTER ASSEMBLY WITH FINISH PANEL (w/o Audio)


    1. A00OVXQ

      Connect the connector and clamp.

    2. A00OQMC

      Attach the 2 clips and hook.

    3. A00OSZP

      Attach the 6 clips.

    4. Attach the 3 claws and 3 hooks to install the panel register.

  15. INSTALL INSTRUMENT PANEL FINISH PANEL END RH (for RHD)


    1. w/o TOYOTA Parking Assist-sensor System:


      1. Attach the 4 clips and 5 claws to install the panel end.

    2. w/ TOYOTA Parking Assist-sensor System:


      1. Connect the connector.

      2. Attach the 4 clips and 5 claws to install the panel end.

        A00OW4UE01

  16. INSTALL GLOVE COMPARTMENT DOOR ASSEMBLY


    1. A00OSS7

      Attach the 2 hinges to install the door.

    2. A00ORZ3E01
      Text in Illustration
      *1 Stopper

      While pushing in the sides of the glove compartment door as indicated by the arrows in the illustration, close the door to engage the 2 stoppers.

  17. INSTALL INSTRUMENT PANEL FINISH PANEL END RH (for LHD)


    1. A00OSPV

      Attach the 4 clips and 5 claws to install the panel end.

  18. INSTALL INSTRUMENT PANEL FINISH PANEL END LH


    1. Attach the 4 clips and 5 claws to install the panel end.

      A00OQEVE01

  19. INSTALL NO. 3 BOX PANEL


    1. When replacing the No. 3 box panel with a new one:


      1. A010S0KE01
        Text in Illustration
        *1 Cut

        Cut off the rib (the piece used to maintain the shape of the panel) shown in the illustration.

    2. Attach the 6 clips to install the box panel.

      A010QVSE02

  20. INSTALL LOWER NO. 1 INSTRUMENT PANEL FINISH PANEL


    1. A00OW2FE01
      Text in Illustration
      *1 Guide
      *2 Clamp

      Attach the guide near the front of the vehicle.

    2. Attach the clamp.

    3. Attach the 2 clips and 5 claws to install the finish panel.

  21. INSTALL LOWER NO. 2 INSTRUMENT PANEL FINISH PANEL


    1. A00OT9HE01
      Text in Illustration
      *1 Guide
      *2 Clamp

      Attach the guide near the front of the vehicle.

    2. Attach the clamp.

    3. Attach the 2 clips and 5 claws to install the finish panel.

  22. INSTALL COMBINATION METER ASSEMBLY


    1. Install the combination meter assembly Click here.

  23. CONNECT CABLE TO NEGATIVE BATTERY TERMINAL

    Note

    When disconnecting the cable, some systems need to be initialized after the cable is reconnected Click here.

  24. RESTORE AUTOAWAY/RETURN FUNCTION (for Power Tilt and Power Telescopic Steering Column)


    1. Restore the Autoaway/Return function setting to the previous condition by changing the customize parameter Click here.

  25. CHECK SRS WARNING LIGHT


    1. Check the SRS warning light Click here.