HEATER FUEL PUMP INSTALLATION


  1. INSTALL HEATER PUMP ASSEMBLY


    1. Install the heater pump assembly with the nut.

      Torque:
      7.5 N*m  { 76 kgf*cm, 66 in.*lbf }

    2. Connect the fuel hose and attach the 2 clips, as shown in the illustration.

    3. Connect the connector.

      A00OV19E01
      Text in Illustration
      *1 Paint Mark *2 0 to -3 mm (0 to -1.181 in.)

  2. INSTALL OUTER COWL TOP PANEL SUB-ASSEMBLY


    1. Install the outer cowl top panel with the 9 bolts.

      Torque:
      8.8 N*m  { 90 kgf*cm, 78 in.*lbf }

    2. Attach the clamp and connect the connector.

  3. INSTALL DIFFERENTIAL PRESSURE SENSOR ASSEMBLY (for DPF)


    1. A003AJ5E01

      Connect the 2 vacuum hoses.

      Note

      Connect the vacuum hoses so that the painted marks of the 2 vacuum hoses are as shown in the illustration.

    2. A003ASH

      Install the sensor with the bolt.

      Torque:
      8.0 N*m  { 82 kgf*cm, 71 in.*lbf }

    3. Connect the sensor connector and attach the wire harness clamp.

  4. INSTALL WINDSHIELD WIPER MOTOR AND LINK ASSEMBLY


    1. A00OJDC

      Move the wiper motor and link in the direction shown by the arrow in the illustration to attach the wiper cushion to the body and install the wiper motor and link.

    2. A00OIUJ

      Install the 2 bolts.

      Torque:
      5.5 N*m  { 56 kgf*cm, 49 in.*lbf }
    3. A00OIY3

      Connect the connector and attach the clamp to install the wire harness to the cowl top panel.

  5. INSTALL COWL TOP VENTILATOR LOUVER LH


    1. A00OI4V

      Attach the 5 claws to install the cowl top ventilator louver LH.

    2. Install the clip.

  6. INSTALL COWL TOP VENTILATOR LOUVER RH


    1. A00OLOR

      Attach the 8 claws to install the cowl top ventilator louver RH.

    2. Install the clip.

  7. INSTALL HOOD TO COWL TOP SEAL


    1. A00OKSF

      Attach the 6 clips and 2 claws to install the hood to cowl top seal.

  8. INSTALL FRONT WIPER ARM AND BLADE ASSEMBLY RH


    1. Operate the wiper and stop the front wiper motor and link at the automatic stop position.

    2. A00OI8VE01
      Text in Illustration
      *1 Wiper Arm Serrations
      *2 Wire Brush
      *3 Wiper Pivot Serrations

      Clean the wiper arm serrations.

    3. When reusing the front wiper motor and link assembly:


      1. Clean the wiper pivot serrations with a wire brush.

    4. A00OMF3E01
      Text in Illustration
      *1 Louver Edge

      Install the front wiper arm and blade assembly RH to the position shown in the illustration with the nut.

      Torque:
      26 N*m  { 265 kgf*cm, 19 ft.*lbf }

      Tech Tips

      Hold the arm hinge by hand when tightening the nut.

      Standard
      Area Specified Condition
      A 29.4 to 44.4 mm (1.16 to 1.75 in.)
      B 36.3 to 51.3 mm (1.43 to 2.02 in.)

  9. INSTALL FRONT WIPER ARM AND BLADE ASSEMBLY LH


    1. Operate the wiper and stop the front wiper motor and link at the automatic stop position.

    2. A00OI8VE01
      Text in Illustration
      *1 Wiper Arm Serrations
      *2 Wire Brush
      *3 Wiper Pivot Serrations

      Clean the wiper arm serrations.

    3. When reusing the front wiper motor and link assembly:


      1. Clean the wiper pivot serrations with a wire brush.

    4. A00OK4RE01
      Text in Illustration
      *1 Louver Edge

      Install the front wiper arm and blade assembly LH to the position shown in the illustration with the nut.

      Torque:
      26 N*m  { 265 kgf*cm, 19 ft.*lbf }

      Tech Tips

      Hold the arm hinge by hand when tightening the nut.

      Standard
      Area Specified Condition
      A 36.3 to 51.3 mm (1.43 to 2.02 in.)
      B 29.4 to 44.4 mm (1.16 to 1.75 in.)

    5. Operate the front wipers while spraying washer fluid on the windshield glass. Make sure that the front wipers function properly and the wipers do not come into contact with the vehicle body.

  10. INSTALL FRONT WIPER ARM HEAD CAP


    1. A00OMYH

      Install the front wiper arm head cap.

      Tech Tips

      Use the same procedure for all front wiper arm head caps.

  11. INSTALL NO. 1 ENGINE COVER


    1. Attach the 4 clips to install the No. 1 engine cover.