HEATER EXHAUST PIPE REMOVAL


  1. REMOVE NO. 1 ENGINE COVER (for 1AD-FTV)


    1. A003DQW

      Hold the rear of the cover and slowly raise it to detach the clip on the rear of the cover. Continue to raise the cover to detach the 3 clips on the front and side of the cover and remove the cover.

      Note

      Attempting to disengage both front and rear clips at the same time may cause the cover to break.

  2. REMOVE NO. 1 ENGINE COVER (for 2AD-FTV)


    1. A003DQW

      Hold the rear of the cover and slowly raise it to detach the clip on the rear of the cover. Continue to raise the cover to detach the 3 clips on the front and side of the cover and remove the cover.

      Note

      Attempting to disengage both front and rear clips at the same time may cause the cover to break.

  3. REMOVE NO. 1 ENGINE COVER (for 2AD-FHV)


    1. A003DQW

      Hold the rear of the cover and slowly raise it to detach the clip on the rear of the cover. Continue to raise the cover to detach the 3 clips on the front and side of the cover and remove the cover.

      Note

      Attempting to disengage both front and rear clips at the same time may cause the cover to break.

  4. REMOVE FRONT WIPER ARM HEAD CAP


    1. A003BEK

      Using a screwdriver, remove the front wiper arm head cap.

      Tech Tips


      • Tape the screwdriver tip before use.

      • Use the same procedure for all front wiper arm head caps.

  5. REMOVE FRONT WIPER ARM AND BLADE ASSEMBLY LH


    1. A003CFU

      Remove the nut and the front wiper arm and blade assembly LH.

  6. REMOVE FRONT WIPER ARM AND BLADE ASSEMBLY RH


    1. A003C4X

      Remove the nut and the front wiper arm and blade assembly RH.

  7. REMOVE HOOD TO COWL TOP SEAL


    1. A003BK8

      Using a clip remover, detach the 6 clips and 2 claws and remove the hood to cowl top seal.

  8. REMOVE COWL TOP VENTILATOR LOUVER RH


    1. A003CSY

      Remove the clip.

    2. Detach the 8 claws and remove the cowl top ventilator louver RH.

  9. REMOVE COWL TOP VENTILATOR LOUVER LH


    1. A003B6G

      Remove the clip.

    2. Detach the 5 claws and remove the cowl top ventilator louver LH.

  10. REMOVE WINDSHIELD WIPER MOTOR AND LINK ASSEMBLY


    1. A003CR8

      Disconnect the connector. Then detach the clamp and remove the wire harness from the cowl top panel.

    2. A003ATE

      Remove the 2 bolts.

    3. A003ANA

      Move the wiper cushion in the direction shown by the arrow in the illustration to detach the wiper cushion from the body and remove the wiper motor and link.

  11. REMOVE DIFFERENTIAL PRESSURE SENSOR ASSEMBLY (for DPF)


    1. A003D5G

      Detach the wire harness clamp and disconnect the sensor connector.

    2. Remove the bolt and sensor.

    3. Disconnect the 2 vacuum hoses.

  12. REMOVE COWL TOP OUTER PANEL


    1. A00OTJV

      Install the outer cowl top panel with the 9 bolts.

      Torque:
      8.8 N*m  { 90 kgf*cm, 78 in.*lbf }
    2. A00OS7D

      Attach the clamp and connect the connector.

  13. REMOVE AIR DUCT


    1. A003BC4

      Remove the clip and air duct.

  14. REMOVE NO. 1 EXHAUST PIPE SUB-ASSEMBLY


    1. A003C77

      Remove the 3 nuts and No. 1 exhaust pipe sub-assembly.

  15. REMOVE HEATER WITH EXHAUST PIPE ASSEMBLY

    A003BUC

    1. Disconnect the connector.

    2. Remove the 3 clips.

    3. Detach the clamp.

    4. A003DVT

      Remove the 3 nuts and heater with exhaust pipe assembly.

  16. REMOVE NO. 2 EXHAUST PIPE SUB-ASSEMBLY


    1. A003E73

      Remove the 2 bolts and No. 2 exhaust pipe sub-assembly.

  17. REMOVE HEAT EXCHANGER UNIT GASKET


    1. A003E76

      Remove the 2 heat exchanger unit gaskets.