OCCUPANT DETECTION SENSOR REASSEMBLY


  1. INSTALL FRONT SEAT CUSHION HEATER ASSEMBLY RH (w/ Seat Heater System)


    1. Remove the peeling paper from a new cushion heater.

    2. A003C0C

      Install the cushion heater to a new front seat cushion pad.

  2. INSTALL SEPARATE TYPE FRONT SEAT CUSHION COVER


    1. A010GGQ

      Attach the hooks to install the cover.

  3. INSTALL SEAT CUSHION COVER WITH PAD


    1. Attach the hooks to install the seat cushion cover with pad.

      A010LAP

    2. w/ Seat Heater System:

      Connect the connector.

    3. A010MAE

      w/ Lumbar Support:

      Attach the wire harness clamp.

    4. for Passenger Side:


      1. A010LZM

        Attach the 2 hooks to install the connector holder.

    5. w/ Seat Heater System:


      1. A010J4I

        Connect the connector.

      2. A010GDU

        Install a new cable tie.

    6. A010LVJ

      Attach the 2 rubber bands.

    7. for Driver Side:


      1. A010IVG

        Attach the 2 claws to install the vertical adjuster handle bracket with connector link.

      2. A010JUA

        Install the connector link and attach the clip.

    8. A010M6T

      Install the reclining handle with the nut.

      Torque:
      25 N*m  { 255 kgf*cm, 18 ft.*lbf }
    9. A010K9Z

      Attach the 2 hooks to install the spring.

  4. INSTALL FRONT SEAT INNER CUSHION SHIELD RH


    1. A010FYQE01
      Text in Illustration
      *1 Hook
      *2 Wire Harness Clamp

      Attach the wire harness clamp and hook to install the shield.

    2. Install the 2 screws.

  5. INSTALL FRONT SEAT INNER BELT ASSEMBLY RH

    Tech Tips


    • Use the same procedure for the RH and LH sides.

    • The procedure listed below is for the LH side.


    1. A003EE0E01
      Text in Illustration
      *1 Protruding Part

      Install the front seat inner belt with the nut.

      Torque:
      41 N*m  { 418 kgf*cm, 30 ft.*lbf }

      Note

      Do not allow the anchor part of the front seat inner belt assembly to overlap the protruding part of the front seat adjuster.

    2. for Driver Side:

      Connect the connector and attach the clamps.

    3. for Passenger Side:

      Connect the connectors and attach the clamps.

  6. INSTALL FRONT POWER SEAT SWITCH (for Power Seat)


    1. A003DD6

      Connect the connector.

    2. Install the switch with the 3 screws.

  7. INSTALL FRONT SEAT CUSHION SHIELD WITH FRONT SEAT INNER NO. 1 CUSHION SHIELD (for Power Seat)


    1. A010H4B

      for Driver Side:

      Connect the connector.

    2. A010L01

      Attach the hook to install the front seat cushion shield LH with front seat inner No. 1 cushion shield.

    3. Install the 2 screws.

    4. A010KW3

      Attach the 2 claws and install the 2 screws.

  8. INSTALL SLIDE AND VERTICAL POWER SEAT SWITCH KNOB (for Power Seat)


    1. A010LMY

      Attach the 4 claws to install the knob.

  9. INSTALL RECLINING POWER SEAT SWITCH KNOB (for Power Seat)


    1. A010M69

      Attach the 2 claws to install the knob.

  10. INSTALL FRONT SEAT CUSHION SHIELD RH (for Manual Seat)


    1. A010I8D

      w/ Lumbar Support:

      Connect the connector.

    2. A010INS

      Attach the claw and hook to install the cushion shield.

    3. Install the 2 screws.

  11. INSTALL RECLINING ADJUSTER RELEASE HANDLE RH (for Manual Seat)


    1. A010KI5

      Attach the claw to install the release handle.