OCCUPANT DETECTION SENSOR DISASSEMBLY


  1. REMOVE RECLINING ADJUSTER RELEASE HANDLE RH (for Manual Seat)


    1. A010LM3

      Raise the reclining adjuster release handle to reveal the claw. Using a screwdriver, detach the claw and remove the release handle.

      Tech Tips

      Tape the screwdriver tip before use.

  2. REMOVE FRONT SEAT CUSHION SHIELD RH (for Manual Seat)


    1. A010KEO

      Remove the 2 screws.

    2. Pull the shield to detach the hook and claw.

    3. Remove the cushion shield.

    4. A010I8D

      w/ Lumbar Support:

      Disconnect the connector.

  3. REMOVE RECLINING POWER SEAT SWITCH KNOB (for Power Seat)


    1. A010IBFE01
      Text in Illustration
      *1 Protective Tape

      Apply protective tape around the cushion shield.

    2. Using a screwdriver, detach the 2 claws and remove the knob.

      Tech Tips

      Tape the screwdriver tip before use.

  4. REMOVE SLIDE AND VERTICAL POWER SEAT SWITCH KNOB (for Power Seat)


    1. A010K86E01
      Text in Illustration
      *1 Protective Tape

      Using a screwdriver, detach the 4 claws and remove the knob.

      Tech Tips

      Tape the screwdriver tip before use.

  5. REMOVE FRONT SEAT CUSHION SHIELD WITH FRONT SEAT INNER NO. 1 CUSHION SHIELD (for Power Seat)


    1. A010GPB

      Remove the 2 screws and detach the 2 claws.

    2. A010HQT

      Remove the 2 screws.

    3. Pull the shield to detach the hook and remove the front seat cushion shield LH with front seat inner No. 1 cushion shield.

    4. A010H4B

      for Driver Side:

      Disconnect the connector.

  6. REMOVE FRONT POWER SEAT SWITCH (for Power Seat)


    1. A003DD6

      Disconnect the connector.

    2. Remove the 3 screws and switch.

  7. REMOVE FRONT SEAT INNER CUSHION SHIELD RH


    1. for Driver Side:

      Disconnect the connector and detach the clamps.

    2. for Passenger Side:

      Disconnect the connectors and detach the clamps.

    3. A003CGA

      Remove the nut and front seat inner belt.

  8. REMOVE FRONT SEAT INNER BELT ASSEMBLY RH

    Tech Tips


    • Use the same procedure for the RH and LH sides.

    • The procedure listed below is for the LH side.


    1. A003EE0E01
      Text in Illustration
      *1 Protruding Part

      Install the front seat inner belt with the nut.

      Torque:
      41 N*m  { 418 kgf*cm, 30 ft.*lbf }

      Note

      Do not allow the anchor part of the front seat inner belt assembly to overlap the protruding part of the front seat adjuster.

    2. for Driver Side:

      Connect the connector and attach the clamps.

    3. for Passenger Side:

      Connect the connectors and attach the clamps.

  9. REMOVE SEAT CUSHION COVER WITH PAD


    1. A010K9Z

      Detach the 2 hooks and remove the spring.

    2. A010M6T

      Remove the nut and reclining handle.

    3. for Driver Side:


      1. A010KSL

        Detach the clip and remove the connector link.

      2. A010H9Y

        Using a screwdriver, detach the 2 claws and remove the vertical adjuster handle bracket with connector link.

        Tech Tips

        Tape the screwdriver tip before use.

    4. A010J2S

      Detach the 2 rubber bands.

    5. w/ Seat Heater System:


      1. A010GDU

        Cut off the cable tie.

      2. A010J4I

        Disconnect the connector.

    6. for Passenger Side:


      1. A010LZM

        Detach the 2 hooks and remove the connector holder.

    7. A010MAE

      w/ Lumbar Support:

      Detach the wire harness clamp.

    8. w/ Seat Heater System:

      Disconnect the connector.

      A010LAP

    9. Detach the hooks and remove the seat cushion cover with pad.

  10. REMOVE SEPARATE TYPE FRONT SEAT CUSHION COVER


    1. A010GGQ

      Detach the hooks and remove the cushion cover.