POWER WINDOW REGULATOR MOTOR (for Front Door) INSTALLATION

Tech Tips


  • Use the same procedure for the RH and LH sides.

  • The procedure listed below is for the LH side.

  • A bolt without a torque specification is shown in the standard bolt chart Click here.


  1. INSTALL FRONT DOOR WINDOW REGULATOR ASSEMBLY LH


    1. Apply MP grease to the sliding and rotating areas of the window regulator.

      Note

      Do not apply grease to the spring of the window regulator.

    2. A006VNZE01
      Text in Illustration
      *1 Temporary bolt

      Temporarily install the temporary bolt to the window regulator.

    3. Insert the window regulator into the door panel. Use the temporary bolt to hang the window regulator on the door panel.

      Note

      Be careful not to drop the window regulator as it may become damaged.

    4. Temporarily install the window regulator with the 5 bolts.

    5. Tighten the 6 bolts.

      Torque:
      8.0 N*m  { 82 kgf*cm, 71 in.*lbf }

  2. INSTALL FRONT DOOR GLASS SUB-ASSEMBLY LH


    1. A00OUC2E01

      Insert the door glass into the door panel along the glass run as indicated by the arrows in the illustration.

      Note

      Be careful not to damage the glass.

    2. Install the door glass to the window regulator with the 2 bolts.

      Torque:
      8.0 N*m  { 82 kgf*cm, 71 in.*lbf }

  3. INSTALL FRONT DOOR SERVICE HOLE COVER LH


    1. Apply butyl tape to the door.

    2. Pass the front door lock remote control cable and front door inside locking cable through a new front door service hole cover.

      Note


      • When installing the service hole cover, pull the links and connectors through the service hole cover.

      • There should be no wrinkles or folds after installing the service hole cover.

      • After installing the service hole cover, check the seal quality.

    3. A00OSQBE01
      Text in Illustration
      *1 Reference Point

      Attach the front door service hole cover according to the reference points on the front door panel.

      Note

      Securely install the front door service hole cover preventing wrinkles and air bubbles.

    4. A00OQI0

      for Power Seat:

      Attach the 3 clamps.

    5. A00OU5X

      for Manual Seat:

      Attach the 2 clamps.

    6. Connect the 3 connectors.

  4. INSTALL FRONT NO. 1 SPEAKER ASSEMBLY


    1. A00OSRME01

      Temporarily install the speaker by attaching the claw of the speaker to the door panel.

    2. Install the speaker with the 4 screws in the order shown in the illustration.

    3. Connect the speaker connector.

      Note

      Do not touch the cone part of the speaker.

  5. INSTALL DOOR FRAME GARNISH LH


    1. A00OQRE

      Install the door frame garnish with the 2 clips.

  6. INSTALL FRONT DOOR INNER GLASS WEATHERSTRIP LH


    1. A00OTU8

      Install the front door inner glass weatherstrip.

  7. INSTALL COURTESY LIGHT ASSEMBLY


    1. A003E87

      Attach the 2 claws to install the light.

  8. INSTALL FRONT DOOR TRIM BOARD SUB-ASSEMBLY LH


    1. A00OUS2

      for Manual Seat:

      Connect the front door lock remote control cable and front door inside locking cable to the front door inside handle sub-assembly.

    2. for Power Seat:


      1. A00OR34

        Connect the front door lock remote control cable and front door inside locking cable to the front door inside handle sub-assembly.

      2. Connect the connector.

      3. A00OR1R

        Attach the wire harness.

    3. A00OQM8

      Attach the front door trim board with the 5 claws of the front door inner glass weatherstrip.

    4. Connect the courtesy light connector.

    5. A00OSKN

      Attach the 2 claws and 10 clips to install the trim board.

    6. Install the 3 screws.

  9. INSTALL FRONT DOOR NO. 1 STIFFENER CUSHION


    1. Install the front door No. 1 stiffener cushion.

  10. INSTALL POWER WINDOW REGULATOR SWITCH ASSEMBLY WITH FRONT DOOR ARMREST BASE PANEL (for Front Passenger Side)

    Tech Tips

    Use the same procedure described for the driver side.

  11. INSTALL POWER WINDOW REGULATOR MASTER SWITCH ASSEMBLY WITH FRONT DOOR ARMREST BASE PANEL (for Driver Side)

    A00OQFLE01

    1. Connect the connector.

    2. Attach the 7 claws and clip to install the front armrest base panel.

  12. INSTALL ASSIST GRIP COVER LH


    1. A00OUW9

      Attach the 9 claws to install the assist grip cover.

  13. INSTALL FRONT DOOR INSIDE HANDLE BEZEL PLUG LH


    1. A00OS81

      Attach the 3 claws to install the inside handle bezel plug.

  14. CONNECT CABLE TO NEGATIVE BATTERY TERMINAL

    Note

    When disconnecting the cable, some systems need to be initialized after the cable is reconnected Click here.