POWER WINDOW CONTROL SYSTEM Front Passenger Side Power Window does not Operate with Front Passenger Side Power Window Switch

DESCRIPTION


WIRING DIAGRAM

A006WJ7E01

INSPECTION PROCEDURE

Note

Inspect the fuses for circuits related to this system before performing the following inspection procedure.

PROCEDURE


  1. CHECK LIN COMMUNICATION SYSTEM


    1. Check for LIN communication system DTCs related to the power window control system Click here.

      OK
      LIN communication system DTCs are not output.

    NG

    GO TO LIN COMMUNICATION SYSTEM Click here

    OK

  2. CHECK FOR DTC (B2312)


    1. Check if DTC B2312 is output Click here.

      OK
      DTC B2312 is not output.

    NG

    GO TO DTC B2312 Click here

    OK

  3. READ VALUE USING INTELLIGENT TESTER (FRONT PASSENGER SIDE DOOR WINDOW REGULATOR ASSEMBLY)


    1. Use the Data List to check if the front door window regulator is functioning properly Click here.

      P-Door Motor
      Tester Display Measurement Item/Range Normal Condition Diagnostic Note
      P Door P/W Up SW Front passenger side power window manual up signal / ON or OFF

      ON: Front passenger side power window manual up switch operated

      OFF: Front passenger side power window switch not operated

      		 -
      P Door P/W Down SW Front passenger side power window manual down signal / ON or OFF

      ON: Front passenger side power window manual down switch operated

      OFF: Front passenger side power window switch not operated

      		 -
      OK
      Display changes according to operation of power window regulator switch.
      Result
      Result Proceed to
      OK (for LHD) A
      OK (for RHD) B
      NG C

    B

    REPLACE FRONT DOOR WINDOW REGULATOR ASSEMBLY LH Click here

    C

    CHECK HARNESS AND CONNECTOR (POWER WINDOW REGULATOR SWITCH ASSEMBLY - BODY GROUND) Click here

    A

    REPLACE FRONT DOOR WINDOW REGULATOR ASSEMBLY RH Click here

  4. CHECK HARNESS AND CONNECTOR (POWER WINDOW REGULATOR SWITCH ASSEMBLY - BODY GROUND)

    A006VBDE01
    Text in Illustration
    *1 for LHD
    *2 for RHD
    *3

    Front view of wire harness connector

    (to Power Window Regulator Switch)

    1. Disconnect the E4*1 or E19*2 switch connector.

      *1: for LHD

      *2: for RHD

    2. Measure the resistance according to the value(s) in the table below.

      Standard Resistance
      for LHD
      Tester Connection Condition Specified Condition
      E4-1 (GND) - Body ground Always Below 1 Ω
      for RHD
      Tester Connection Condition Specified Condition
      E19-1 (GND) - Body ground Always Below 1 Ω

    NG

    REPAIR OR REPLACE HARNESS OR CONNECTOR

    OK

  5. CHECK HARNESS AND CONNECTOR (FRONT DOOR WINDOW REGULATOR ASSEMBLY - BATTERY AND BODY GROUND)

    A006U0AE01
    Text in Illustration
    *1 for LHD
    *2 for RHD
    *3

    Front view of wire harness connector

    (to Front Door Window Regulator)

    1. Disconnect the E6*1 or E20*2 regulator connector.

      *1: for LHD

      *2: for RHD

    2. Measure the voltage and resistance according to the value(s) in the table below.

      Standard Voltage
      for LHD
      Tester Connection Condition Specified Condition
      E6-2 (B) - Body ground Always 11 to 14 V
      for RHD
      Tester Connection Condition Specified Condition
      E20-2 (B) - Body ground Always 11 to 14 V
      Standard Resistance
      for LHD
      Tester Connection Condition Specified Condition
      E6-1 (GND) - Body ground Always Below 1 Ω
      for RHD
      Tester Connection Condition Specified Condition
      E20-1 (GND) - Body ground Always Below 1 Ω

    NG

    REPAIR OR REPLACE HARNESS OR CONNECTOR

    OK

  6. INSPECT POWER WINDOW REGULATOR SWITCH ASSEMBLY

    A006U4FE04
    Text in Illustration
    *1

    Component without harness connected

    (Power Window Regulator Switch)

    1. Remove the power window regulator switch Click here.

    2. Measure the resistance according to the value(s) in the table below.

      Standard Resistance
      Tester Connection Switch Condition Specified Condition
      6 (UP) - 1 (GND) Manual up operation Below 1 Ω
      7 (DOWN) - 1 (GND) Manual down operation Below 1 Ω

    NG

    REPLACE POWER WINDOW REGULATOR SWITCH ASSEMBLY Click here

    OK

  7. CHECK HARNESS AND CONNECTOR (POWER WINDOW REGULATOR SWITCH ASSEMBLY - FRONT DOOR WINDOW REGULATOR ASSEMBLY)

    A006V6JE02
    Text in Illustration
    *1 for LHD
    *2 for RHD
    *3

    Front view of wire harness connector

    (to Power Window Regulator Switch)
    *4

    Front view of wire harness connector

    (to Front Door Window Regulator)

    *1: for LHD

    *2: for RHD


    1. Disconnect the E4*1 or E19*2 switch connector.

    2. Disconnect the E6*1 or E20*2 regulator connector.

    3. Measure the resistance according to the value(s) in the table below.

      Standard Resistance
      for LHD
      Tester Connection Condition Specified Condition
      E4-6 (UP) - E6-10 (UP) Always Below 1 Ω
      E4-7 (DOWN) - E6-7 (DOWN) Always Below 1 Ω
      E4-8 (AUTO) - E6-4 (AUTO) Always Below 1 Ω
      E4-6 (UP) or E6-10 (UP) - Body ground Always 10 kΩ or higher
      E4-7 (DOWN) or E6-7 (DOWN) - Body ground Always 10 kΩ or higher
      E4-8 (AUTO) or E6-4 (AUTO) - Body ground Always 10 kΩ or higher
      for RHD
      Tester Connection Condition Specified Condition
      E19-6 (UP) - E20-10 (UP) Always Below 1 Ω
      E19-7 (DOWN) - E20-7 (DOWN) Always Below 1 Ω
      E19-8 (AUTO) - E20-4 (AUTO) Always Below 1 Ω
      E19-6 (UP) or E20-10 (UP) - Body ground Always 10 kΩ or higher
      E19-7 (DOWN) or E20-7 (DOWN) - Body ground Always 10 kΩ or higher
      E19-8 (AUTO) or E20-4 (AUTO) - Body ground Always 10 kΩ or higher
      Result
      Result Proceed to
      OK (for LHD) A
      OK (for RHD) B
      NG C

    B

    REPLACE FRONT DOOR WINDOW REGULATOR ASSEMBLY LH Click here

    C

    REPAIR OR REPLACE HARNESS OR CONNECTOR

    A

    REPLACE FRONT DOOR WINDOW REGULATOR ASSEMBLY RH Click here