POWER WINDOW REGULATOR MOTOR (for Rear Door) REMOVAL

Tech Tips


  • Use the same procedure for the RH and LH sides.

  • The procedure listed below is for the LH side.


  1. PRECAUTION

    Note

    After turning the ignition switch off, waiting time may be required before disconnecting the cable from the battery terminal. Therefore, make sure to read the disconnecting the cable from the battery terminal notice before proceeding with work Click here.

  2. DISCONNECT CABLE FROM NEGATIVE BATTERY TERMINAL

    CAUTION:

    Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to disable the SRS system.

    Note

    When disconnecting the cable, some systems need to be initialized after the cable is reconnected Click here.

  3. REMOVE REAR DOOR NO. 1 STIFFENER CUSHION


    1. A00ORCD

      Remove the stiffener cushion.

  4. REMOVE REAR DOOR INSIDE HANDLE BEZEL PLUG LH


    1. A00OS4V

      Using moulding remover A, detach the 3 claws and remove the bezel plug.

  5. REMOVE DOOR ASSIST GRIP COVER LH


    1. A00OUKL

      Using moulding remover A, detach the 10 claws and remove the assist grip cover.

  6. REMOVE REAR POWER WINDOW REGULATOR SWITCH ASSEMBLY WITH REAR DOOR ARMREST BASE PANEL


    1. A00OU7X

      Insert clip remover between the plate and trim board.

    2. Turn the handle counterclockwise to remove the snap ring and handle.

  7. REMOVE REAR DOOR TRIM BOARD SUB-ASSEMBLY LH


    1. A00OV40

      Remove the 3 screws.

    2. Using a clip remover, detach the 8 clips.

    3. A00ORQJE01
      Text in Illustration
      *1 w/ Rear Door Sunshade
      *2 w/o Rear Door Sunshade

      Pull out the rear door trim board in the direction indicated by the arrow.

    4. for 11 Speakers:


      1. Disconnect the connector.

    5. A00ORAH

      Disconnect the 2 cables from the inside handle.

  8. REMOVE REAR DOOR INNER GLASS WEATHERSTRIP LH


    1. A00OS1Z

      Remove the inner glass weatherstrip by pulling it upward in the direction indicated by the arrow in the illustration.

  9. REMOVE REAR DOOR FRAME GARNISH LH


    1. A00OV61E01

      Detach the 2 clips.

    2. Detach the claws and remove the rear door frame garnish.

  10. REMOVE REAR DOOR SERVICE HOLE COVER LH


    1. A00ORC8

      Disconnect connector and remove the service hole cover.

      Tech Tips

      Remove the remaining tape on the door.

  11. REMOVE REAR DOOR GLASS RUN LH


    1. A00OTWXE01

      Remove the rear door glass run.

  12. REMOVE REAR DOOR WINDOW DIVISION BAR SUB-ASSEMBLY LH


    1. A00OUN7E01

      Remove the screw.

    2. Remove the 2 bolts and rear door window division bar sub-assembly.

  13. REMOVE REAR DOOR QUARTER WINDOW GLASS LH


    1. A00ORWTE01

      Remove the rear door quarter window glass and rear door quarter window weatherstrip as a unit as shown in the illustration.

  14. REMOVE REAR DOOR GLASS SUB-ASSEMBLY LH


    1. A00OT3V

      Remove the rear door glass sub-assembly from the rear door window regulator sub-assembly as shown in the illustration.

      Note

      Do not damage the door glass.

  15. REMOVE REAR DOOR WINDOW REGULATOR ASSEMBLY LH


    1. A00OS5BE01
      Text in Illustration
      *1 Temporary Bolt

      Disconnect the connector.

    2. Loosen the temporary bolt.

      Note

      Do not remove the temporary bolt. If the temporary bolt is removed, the rear door window regulator may fall and cause damage.

    3. Remove the 3 bolts.

    4. Remove the rear door window regulator assembly.

    5. Remove the temporary bolt from the rear door window regulator.