EXHAUST PIPE INSTALLATION


  1. INSTALL FRONT EXHAUST PIPE ASSEMBLY


    1. Check the free length of the compression spring.


      1. A00E9UU

        Using a vernier caliper, measure the free length of the compression spring.

        Minimum length
        41.5 mm (1.63 in.)

        If the free length is less than the minimum, replace the compression spring.

    2. Connect the front exhaust pipe to the 2 exhaust pipe supports.

      Note

      If any of the exhaust pipe supports are removed, be sure to install the type of exhaust pipe support shown in the illustration as there are different types of exhaust pipe supports used.

      A00E74FE01

    3. Install a new gasket to the front exhaust pipe.

      Note

      Be sure to install the type of gasket shown in the illustration as there are different types of gaskets used.

      A00E7KIE01

    4. Install the front exhaust pipe with the 2 compression springs and 2 bolts to the exhaust manifold converter.

      Torque:
      43 N*m  { 438 kgf*cm, 32 ft.*lbf }

      Note

      Be sure to install the type of bolt shown in the illustration as there are different types of bolts used.

      A00E9BKE01

  2. INSTALL AIR FUEL RATIO SENSOR


    1. A00E8AYE01

      Using SST, install the air fuel ratio sensor.

      SST
      09224-00010
      Torque:
      without SST
      44 N*m  { 449 kgf*cm, 32 ft.*lbf }
      with SST
      40 N*m  { 408 kgf*cm, 30 ft.*lbf }

      Tech Tips


      • Use a torque wrench with a fulcrum length of 300 mm (11.8 in.).

      • Make sure SST and the wrench are connected in a straight line.

    2. Connect the air fuel ratio sensor connector and clamp.

    3. A00E73S

      Install the harness clamp.

  3. INSTALL FRONT FLOOR CENTER BRACE


    1. A00E8VE

      Install the front floor center brace with the 4 bolts.

      Torque:
      51 N*m  { 520 kgf*cm, 38 ft.*lbf }

  4. INSTALL NO. 2 ENGINE UNDER COVER


    1. A00E945

      Install the No. 2 engine under cover with the 4 clips.

  5. INSTALL TAILPIPE ASSEMBLY


    1. Check the free length of the compression spring.


      1. A00E9UU

        Using a vernier caliper, measure the free length of the compression spring.

        Minimum length
        38.5 mm (1.52 in.)

        If the free length is less than the minimum, replace the compression spring.

    2. Connect the tailpipe to the 4 exhaust pipe supports.

      Note

      If any of the exhaust pipe supports are removed, be sure to install the type of exhaust pipe support shown in the illustration as there are different types of exhaust pipe supports used.

      A00E9J1E01

    3. Install a new gasket to the front exhaust pipe.

      Note

      Be sure to install the type of gasket shown in the illustration as there are different types of gaskets used.

      A00E7Q8E01

    4. Install the tailpipe with the 2 compression springs and 2 bolts.

      Torque:
      43 N*m  { 438 kgf*cm, 32 ft.*lbf }

      Note

      Be sure to install the type of bolt shown in the illustration as there are different types of bolts used.

      A00EB0FE01

  6. INSPECT FOR EXHAUST GAS LEAK


    1. Check that there are no exhaust gas leaks from the points (connection areas of the exhaust pipes and installation areas of each sensor) shown in the illustration.

      A00E806