CLUTCH PEDAL (for RHD) INSTALLATION


  1. INSTALL CLUTCH PEDAL TURNOVER BUSH

    A010QWWE01
    Text in Illustration
    *1 MP grease

    1. Install the clutch pedal turnover bush to the clutch pedal sub-assembly.

    2. Apply MP grease to the inside of the clutch pedal turnover bush.

  2. INSTALL CLUTCH MASTER CYLINDER PUSH ROD CLEVIS BUSHING

    A010QWFE01
    Text in Illustration
    *1 MP grease

    1. Apply MP grease to the inside of a new clutch master cylinder push rod clevis bushing.

    2. Install the clutch master cylinder push rod clevis bushing to the clutch pedal sub-assembly.

      Tech Tips

      Install the clutch master cylinder push rod clevis bushing from the left side of the vehicle.

  3. INSTALL NO. 1 CLUTCH PEDAL CUSHION


    1. A010S0A

      Install the 2 No. 1 clutch pedal cushions to the clutch pedal sub-assembly.

  4. INSTALL CLUTCH PEDAL BUSHING

    A010QZ3E01
    Text in Illustration
    *1 MP grease

    1. Apply MP grease to both sides of 2 new clutch pedal bushings.

    2. Install the 2 clutch pedal bushings and collar to the clutch pedal sub-assembly.

  5. INSTALL CLUTCH PEDAL PAD


    1. Install the clutch pedal pad to the clutch pedal sub-assembly.

  6. INSTALL CLUTCH PEDAL SUB-ASSEMBLY


    1. A010QRO

      Install the clutch pedal sub-assembly to the clutch pedal support sub-assembly with the bolt and nut.

      Torque:
      37 N*m  { 375 kgf*cm, 27 ft.*lbf }

      Tech Tips

      Install the bolt from the left side of the vehicle.

  7. INSTALL NO. 1 PEDAL SPRING HOOK

    A010NQQE01
    Text in Illustration
    *1 MP grease

    1. Apply MP grease to the contact surface of the No. 1 pedal spring hook.

    2. Install the No. 1 pedal spring hook.

  8. INSTALL CLUTCH PEDAL SPRING

    A010SELE01
    Text in Illustration
    *1 MP grease

    1. Apply MP grease to the contact surface of the spring hook.

    2. Install the clutch pedal spring.

  9. INSTALL CLUTCH PEDAL STOPPER BOLT


    1. A010NYU

      Install the clutch pedal stopper bolt together with the nut so that its end touches the No. 1 clutch pedal cushion.

      Tech Tips

      Tighten the lock nut to the specified torque when adjusting the clutch pedal.

  10. INSTALL CLUTCH PEDAL SPRING HOLDER

    A010P49E01
    Text in Illustration
    *1 MP grease

    1. Apply MP grease to the contact surfaces of the clutch pedal spring holder.

    2. Install the clutch pedal spring holder to the clutch pedal support sub-assembly.

  11. INSTALL TURN OVER SPRING SEAT COMPRESSION SPRING

    A010RR7E01
    Text in Illustration
    *1 MP grease

    1. Apply MP grease to the contact surfaces of the clutch pedal and turn over seat compression spring.

    2. Install the turn over seat compression spring to the clutch pedal and clutch pedal spring holder.

  12. INSTALL CENTER OVER SPRING CAP

    A010NBP

    1. Install the center over spring cap to the clutch pedal sub-assembly.

      Tech Tips

      Install the center over spring cap from the right side of the vehicle.

  13. INSTALL CLUTCH START SWITCH ASSEMBLY

    A010PLK

    1. Install the clutch start switch assembly with the nut.

      Torque:
      16 N*m  { 160 kgf*cm, 12 ft.*lbf }

  14. INSTALL BRAKE PEDAL STROKE SENSOR ASSEMBLY (CLUTCH PEDAL STROKE SENSOR)

    Note

    Do not drop the sensor. If the sensor has been dropped, replace the sensor with a new one.


    1. When installing a new brake pedal stroke sensor assembly (clutch pedal stroke sensor):

      Note

      Do not break the sensor lever set pin before installing the brake pedal stroke sensor (clutch pedal stroke sensor) with the bolts. If the sensor lever set pin breaks while tightening the bolt, do not use that sensor.


      1. A00OR6JE01
        Text in Illustration
        *1 Pin
        *2 Lever
        *3 Groove

        Connect the sensor connector.

      2. for LHD:

        Install a new sensor with the 2 bolts.

        Torque:
        8.5 N*m  { 87 kgf*cm, 75 in.*lbf }

        Note


        • Engage the sensor lever with the clutch pedal groove.

        • Check that there is no foreign matter attached to the contact surface of the sensor.

        • Check that the tip of the sensor lever is protruding from the clutch pedal groove.

      3. for RHD:

        Install a new sensor with the 2 nuts.

        Torque:
        8.5 N*m  { 87 kgf*cm, 75 in.*lbf }

        Note


        • Engage the sensor lever with the clutch pedal groove.

        • Check that there is no foreign matter attached to the contact surface of the sensor.

        • Check that the tip of the sensor lever is protruding from the clutch pedal groove.

      4. Firmly depress the clutch pedal and break the pin.

      5. Remove the broken pin.

    2. When reusing the brake pedal stroke sensor assembly (clutch pedal stroke sensor):


      1. A00ORZ0E02
        Text in Illustration
        *1 Lever
        *2 Groove

        Connect the sensor connector.

        Note

        Do not drop the sensor. If the sensor has been dropped, replace the sensor with a new one.

      2. for LHD:

        Temporarily install the sensor with the 2 bolts.

        Note


        • Engage the sensor lever with the brake clutch groove.

        • Check that there is no foreign matter attached to the contact surface of the sensor.

      3. for RHD:

        Temporarily install the sensor with the 2 nuts.

        Note


        • Engage the sensor lever with the clutch pedal groove.

        • Check that there is no foreign matter attached to the contact surface of the sensor.

      4. Connect the cable to the negative battery terminal.

      5. Connect the intelligent tester to the DLC3.

      6. Turn the ignition switch to ON.

      7. Turn the intelligent tester on.

      8. Enter the following menus: Chassis / Electric Parking Brake / Data List.

      9. A00ORGLE01

        While reading the value of the stroke sensor shown in the Data list, turn the sensor slowly to the right and left to adjust the output voltage to the standard voltage.

        Standard Voltage
        Tester Display Measurement Item/Range Normal Condition Diagnostic Note
        SKS1 Raw Value of AD

        Brake pedal stroke sensor (Clutch pedal stroke sensor)(SKS1) voltage display /

        Min.: 0 V

        Max.: 5 V

        		 When clutch pedal is released: 0.8 to 1.2 V -

      10. for LHD:

        Tighten the 2 bolts.

        Torque:
        8.5 N*m  { 87 kgf*cm, 75 in.*lbf }

        Note

        Do not depress the clutch pedal after turning the ignition switch to ON.

      11. for RHD:

        Tighten the 2 nuts.

        Torque:
        8.5 N*m  { 87 kgf*cm, 75 in.*lbf }

        Note

        Do not depress the clutch pedal after turning the ignition switch to ON.

      12. Turn the ignition switch off.

      13. Disconnect the cable from the negative battery terminal.

      14. Disconnect the intelligent tester.

  15. INSTALL CLUTCH PEDAL SUPPORT SUB-ASSEMBLY


    1. A010R9C

      Install the clutch pedal support sub-assembly with the 2 nuts and 2 bolts.

      Torque:
      for bolt
      19 N*m  { 195 kgf*cm, 14 ft.*lbf }
      for nut
      18 N*m  { 178 kgf*cm, 13 ft.*lbf }

    2. Connect the clutch start switch assembly connector and brake pedal stroke sensor assembly connector.

  16. INSTALL CLUTCH MASTER CYLINDER PUSH ROD CLEVIS WITH HOLE PIN

    A010Q8LE01
    Text in Illustration
    *1 MP grease

    1. Apply MP grease to the contact surface of the clutch master cylinder push rod clevis with hole pin.

    2. Connect the clevis to the clutch pedal sub-assembly with the clutch master cylinder push rod clevis with hole pin.

      Tech Tips

      Install the clutch master cylinder push rod clevis with hole pin from the left side of the vehicle.

    3. Install the clip to the clutch master cylinder push rod clevis with hole pin.

  17. INSPECT AND ADJUST CLUTCH PEDAL SUB-ASSEMBLY


    1. Inspect and adjust the clutch pedal sub-assembly Click here.

  18. INSTALL LOWER NO. 1 INSTRUMENT PANEL AIRBAG ASSEMBLY


    1. Install the lower No. 1 instrument panel airbag assembly Click here.

  19. INSTALL UPPER INSTRUMENT PANEL SUB-ASSEMBLY


    1. Install the upper instrument panel sub-assembly Click here.