ECD SYSTEM (for CCo) Starter Signal Circuit

DESCRIPTION

While the engine is being cranked, current flows from terminal ST2 of the ignition switch to the ST fuse and also flows to terminal STA of the ECM (STA signal).

WIRING DIAGRAM

A00EAT2E03
A00EAYVE01

INSPECTION PROCEDURE

Note


  • Inspect the fuses of circuits related to this system before performing the following inspection procedure.

  • After replacing the ECM, the new ECM needs registration Click here and initialization Click here.

Tech Tips

This chart is based on the premise that the engine can crank normally. If the engine cannot crank normally, proceed to the problem symptoms table Click here.

PROCEDURE


  1. CHECK IF VEHICLE IS EQUIPPED WITH ENTRY AND START SYSTEM


    1. Check if the vehicle is equipped with the entry and start system.

      Result
      Result Proceed to
      w/o Entry and Start System A
      w/ Entry and Start System B

    B

    READ VALUE USING INTELLIGENT TESTER (STARTER SIGNAL) Click here

    A

  2. READ VALUE USING INTELLIGENT TESTER (STARTER SIGNAL)


    1. Connect the intelligent tester to the DLC3.

    2. Turn the ignition switch to ON.

    3. Turn the tester on.

    4. Enter the following menus: Powertrain / Engine and ECT / Data List / Starter Signal.

    5. Read the value.

      OK
      Ignition Switch Position Starter Signal
      ON OFF
      START ON

    NG

    CHECK STARTER RELAY (POWER SOURCE) Click here

    OK

    REPAIR PROCEED TO NEXT CIRCUIT INSPECTION SHOWN IN PROBLEM SYMPTOMS TABLE

  3. CHECK STARTER RELAY (POWER SOURCE)


    1. A00EBDZE01
      Text in Illustration
      *1 No. 1 Relay Block
      *2 ST Relay

      Remove the ST relay from the No. 1 relay block.

    2. Measure the voltage according to the value(s) in the table below.

      Standard Voltage
      Tester Connection Condition Specified Condition
      ST relay terminal 1 - Body ground Engine cranking 11 to 14 V

      Tech Tips

      The engine does not crank because the relay is not installed.

    3. Reinstall the ST relay.


    NG

    CHECK HARNESS AND CONNECTOR (ST RELAY - CLUTCH PEDAL SWITCH ASSEMBLY) Click here

    OK

  4. INSPECT STARTER RELAY


    1. A00E92W

      Remove the ST relay from the No. 1 relay block.

    2. Measure the resistance according to the value(s) in the table below.

      Standard Resistance
      Tester Connection Condition Specified Condition
      3 - 5 Battery voltage not applied between terminals 1 and 2 10 kΩ or higher
      3 - 5 Battery voltage applied between terminals 1 and 2 Below 1 Ω

    3. Reinstall the ST relay.


    NG

    REPLACE STARTER RELAY

    OK

  5. CHECK HARNESS AND CONNECTOR (ST RELAY - BODY GROUND)


    1. A00EBDZE01
      Text in Illustration
      *1 No. 1 Relay Block
      *2 ST Relay

      Remove the ST relay from the No. 1 relay block.

    2. Measure the resistance according to the value(s) in the table below.

      Standard Resistance
      Tester Connection Condition Specified Condition
      ST relay terminal 2 - Body ground Always Below 1 Ω

    3. Reinstall the ST relay.


    NG

    REPAIR OR REPLACE HARNESS OR CONNECTOR (ST RELAY - BODY GROUND)

    OK

    REPAIR OR REPLACE HARNESS OR CONNECTOR (ECM - CLUTCH PEDAL SWITCH ASSEMBLY)

  6. CHECK HARNESS AND CONNECTOR (ST RELAY - CLUTCH PEDAL SWITCH ASSEMBLY)


    1. A00E9O9E01
      Text in Illustration
      *1

      Front view of wire harness connector

      (to Clutch Pedal Switch Assembly)
      *2 No. 1 Relay Block
      *3 ST Relay

      Remove the ST relay from the No. 1 relay block.

    2. Disconnect the clutch pedal switch assembly connector.

    3. Measure the resistance according to the value(s) in the table below.

      Standard Resistance (Check for Open)
      Tester Connection Condition Specified Condition
      ST relay terminal 1 - A3-1 Always Below 1 Ω
      Standard Resistance (Check for Short)
      Tester Connection Condition Specified Condition
      ST relay terminal 1 or A3-1 - Body ground Always 10 kΩ or higher

    4. Reinstall the ST relay.

    5. Reconnect the clutch pedal switch assembly connector.


    NG

    REPAIR OR REPLACE HARNESS OR CONNECTOR (ST RELAY - CLUTCH PEDAL SWITCH ASSEMBLY)

    OK

  7. INSPECT CLUTCH PEDAL SWITCH


    1. A00E967E03

      Disconnect the clutch pedal switch assembly connector.

    2. Measure the resistance according to the value(s) in the table below.

      Standard Resistance
      Tester Connection Switch Condition Specified Condition
      1 - 2 Pin not pushed 10 kΩ or higher
      Pin pushed Below 1 Ω

    3. Reconnect the clutch pedal switch assembly connector.


    NG

    REPLACE CLUTCH PEDAL SWITCH Click here

    OK

  8. CHECK HARNESS AND CONNECTOR (CLUTCH PEDAL SWITCH ASSEMBLY - IGNITION SWITCH ASSEMBLY)


    1. A00E9XXE01
      Text in Illustration
      *1

      Front view of wire harness connector

      (to Clutch Pedal Switch Assembly)
      *2

      Front view of wire harness connector

      (to Ignition Switch Assembly)

      Disconnect the clutch pedal switch assembly connector.

    2. Disconnect the ignition switch assembly connector.

    3. Measure the resistance according to the value(s) in the table below.

      Standard Resistance (Check for Open)
      Tester Connection Condition Specified Condition
      A3-2 - D98-1 (ST1) Always Below 1 Ω
      Standard Resistance (Check for Short)
      Tester Connection Condition Specified Condition
      A3-2 or D98-1 (ST1) - Body ground Always 10 kΩ or higher

    4. Reconnect the clutch pedal switch assembly connector.

    5. Reconnect the ignition switch assembly connector.


    NG

    REPAIR OR REPLACE HARNESS OR CONNECTOR (CLUTCH PEDAL SWITCH ASSEMBLY - IGNITION SWITCH ASSEMBLY)

    OK

  9. INSPECT IGNITION SWITCH ASSEMBLY


    1. A00EAWEE06
      Text in Illustration
      *1

      Component without harness connected

      (Ignition Switch Assembly)

      Disconnect the ignition switch assembly connector.

    2. Measure the resistance according to the value(s) in the table below.

      Standard Resistance
      Tester Connection Ignition Switch Position Specified Condition
      All terminals Off 10 kΩ or higher
      2 (AM1) - 1 (ST1) START Below 1 Ω

    3. Reconnect the ignition switch assembly connector.


    NG

    REPLACE IGNITION SWITCH ASSEMBLY Click here

    OK

    REPAIR OR REPLACE HARNESS OR CONNECTOR (IGNITION SWITCH ASSEMBLY - BATTERY)

  10. READ VALUE USING INTELLIGENT TESTER (STARTER SIGNAL)


    1. Connect the intelligent tester to the DLC3.

    2. Turn the ignition switch to ON.

    3. Turn the tester on.

    4. Enter the following menus: Powertrain / Engine and ECT / Data List / Starter Signal.

    5. Read the value.

      OK
      Ignition Switch Position Starter Signal
      ON OFF
      START ON

    NG

    CHECK STARTER RELAY (POWER SOURCE) Click here

    OK

    PROCEED TO NEXT CIRCUIT INSPECTION SHOWN IN PROBLEM SYMPTOMS TABLE Click here

  11. CHECK STARTER RELAY (POWER SOURCE)


    1. A00EBDZE01
      Text in Illustration
      *1 No. 1 Relay Block
      *2 ST Relay

      Remove the ST relay from the No. 1 relay block.

    2. Measure the voltage according to the value(s) in the table below.

      Standard Voltage
      Tester Connection Condition Specified Condition
      ST relay terminal 1 - Body ground Engine cranking 11 to 14 V

      Tech Tips

      The engine does not crank because the relay is not installed.

    3. Reinstall the ST relay.


    NG

    CHECK HARNESS AND CONNECTOR (ST RELAY - CLUTCH PEDAL SWITCH ASSEMBLY) Click here

    OK

  12. INSPECT STARTER RELAY


    1. A00E92W

      Remove the ST relay from the No. 1 relay block.

    2. Measure the resistance according to the value(s) in the table below.

      Standard Resistance
      Tester Connection Condition Specified Condition
      3 - 5 Battery voltage not applied between terminals 1 and 2 10 kΩ or higher
      3 - 5 Battery voltage applied between terminals 1 and 2 Below 1 Ω

    3. Reinstall the ST relay.


    NG

    REPLACE STARTER RELAY

    OK

  13. CHECK HARNESS AND CONNECTOR (ST RELAY - BODY GROUND)


    1. A00EBDZE01
      Text in Illustration
      *1 No. 1 Relay Block
      *2 ST Relay

      Remove the ST relay from the No. 1 relay block.

    2. Measure the resistance according to the value(s) in the table below.

      Standard Resistance
      Tester Connection Condition Specified Condition
      ST relay terminal 2 - Body ground Always Below 1 Ω

    3. Reinstall the ST relay.


    NG

    REPAIR OR REPLACE HARNESS OR CONNECTOR (ST RELAY - BODY GROUND)

    OK

    REPAIR OR REPLACE HARNESS OR CONNECTOR (ECM - CLUTCH PEDAL SWITCH ASSEMBLY)

  14. CHECK HARNESS AND CONNECTOR (ST RELAY - CLUTCH PEDAL SWITCH ASSEMBLY)


    1. A00E9O9E01
      Text in Illustration
      *1

      Front view of wire harness connector

      (to Clutch Pedal Switch Assembly)
      *2 No. 1 Relay Block
      *3 ST Relay

      Remove the ST relay from the No. 1 relay block.

    2. Disconnect the clutch pedal switch assembly connector.

    3. Measure the resistance according to the value(s) in the table below.

      Standard Resistance (Check for Open)
      Tester Connection Condition Specified Condition
      ST relay terminal 1 - A3-1 Always Below 1 Ω
      Standard Resistance (Check for Short)
      Tester Connection Condition Specified Condition
      ST relay terminal 1 or A3-1 - Body ground Always 10 kΩ or higher

    4. Reinstall the ST relay.

    5. Reconnect the clutch pedal switch assembly connector.


    NG

    REPAIR OR REPLACE HARNESS OR CONNECTOR (ST RELAY - CLUTCH PEDAL SWITCH ASSEMBLY)

    OK

  15. INSPECT CLUTCH PEDAL SWITCH


    1. A00E967E07

      Disconnect the clutch pedal switch assembly connector.

    2. Measure the resistance according to the value(s) in the table below.

      Standard Resistance
      Tester Connection Switch Condition Specified Condition
      1 - 2 Pin not pushed 10 kΩ or higher
      Pin pushed Below 1 Ω

    3. Reconnect the clutch pedal switch assembly connector.


    NG

    REPLACE CLUTCH PEDAL SWITCH

    OK

  16. CHECK HARNESS AND CONNECTOR (CLUTCH PEDAL SWITCH ASSEMBLY - POWER MANAGEMENT CONTROL ECU)


    1. A00E79TE10
      Text in Illustration
      *1

      Front view of wire harness connector

      (to Clutch Pedal Switch Assembly)
      *2

      Rear view of wire harness connector

      (to Power Management Control ECU)

      Disconnect the clutch pedal switch assembly connector.

    2. Disconnect the power management control ECU connector.

    3. Measure the resistance according to the value(s) in the table below.

      Standard Resistance (Check for Open)
      Tester Connection Condition Specified Condition
      A3-2 - D113-3 (STAR) Always Below 1 Ω
      Standard Resistance (Check for Short)
      Tester Connection Condition Specified Condition
      A3-2 or D113-3 (STAR) - Body ground Always 10 kΩ or higher

    4. Reconnect the clutch pedal switch assembly connector.

    5. Reconnect the power management control ECU connector.


    NG

    REPAIR OR REPLACE HARNESS OR CONNECTOR (CLUTCH PEDAL SWITCH ASSEMBLY - POWER MANAGEMENT CONTROL ECU)

    OK

    GO TO ENTRY AND START SYSTEM Click here