OIL PUMP INSTALLATION

Note


  • When replacing the injectors (including shuffling the injectors between the cylinders), common rail, intake manifold or cylinder head, it is necessary to replace the injection pipes with new ones.

  • When replacing the fuel supply pump, common rail, intake manifold or cylinder head, it is necessary to replace the fuel inlet pipe with a new one.


  1. INSTALL FRONT CRANKSHAFT OIL SEAL


    1. A00OTOVE01
      Text in Illustration
      *1 Oil Seal
      *2 Timing Chain Cover

      Using SST and a hammer, tap in a new oil seal until its surface is flush with the timing chain cover edge.

      SST
      09223-50010
      Standard depth
      0 to 0.6 mm (0 to 0.236 in.)

      Note


      • Keep the lip of the oil seal free from foreign matter.

      • Do not tap in the oil seal at an angle.

    2. Apply MP grease to the lip of the oil seal.

      Note


      • Do not allow foreign matter to contact the lip of the oil seal.

      • Do not allow MP grease to contact the dust seal.

  2. INSTALL STRAIGHT SCREW PLUG


    1. A00OVWC

      Using a 10 mm socket hexagon wrench, install a new gasket and the straight screw plug.

      Torque:
      19 N*m  { 194 kgf*cm, 14 ft.*lbf }

  3. INSTALL TIMING CHAIN COVER SUB-ASSEMBLY


    1. A00OTIYE01
      Text in Illustration
      *1 Gasket
      *2 O-Ring

      Install a new gasket and new O-ring to the timing chain cover.

    2. Remove any old seal packing material.

    3. Apply seal packing in a continuous line to the timing chain cover as shown in the following illustration.

      A00OTGBE01
      Seal packing
      Toyota Genuine Seal Packing Black, Three Bond 1207B or equivalent
      Apply Seal Packing as Follows
      Area Seal Packing Diameter (Round) Seal Packing Dimension (Flat) Seal Packing Application Length
      A - A 2.0 to 4.0 mm (0.0787 to 0.157 in.) - -
      B - B 8.0 to 10 mm (0.315 to 0.394 in.) - 30 mm (1.18 in.)
      C - C - 13 mm (0.512 in.) or more wide and 6.0 mm (0.236 in.) or more thick 15 mm (0.591 in.)

      Note


      • Be sure to clean and degrease the contact surfaces, especially the 4 areas indicated by the arrows in the illustration.

      • When the contact surfaces are wet, wipe them off with an oil-free cloth before applying seal packing.

      • When applying seal packing to area C - C, apply it in the direction of the white arrows in the illustration.

      • Install the timing chain cover within 3 minutes and tighten the bolts within 15 minutes after applying seal packing.

      • Do not start the engine for at least 4 hours after installation.

    4. A00OVQ1E01
      Text in Illustration
      *1 Adhesive
      *2 Bolt and New Seal Washer

      Apply adhesive to the 4 bolts labeled B.

      Adhesive
      Toyota Genuine Adhesive 1324, Three Bond 1324 or equivalent

    5. Temporarily install the timing chain cover and a new seal washer with the 13 bolts.

      Bolt Length
      Item Specified Condition
      Bolt A 60 mm (2.36 in.)
      Bolt B 30 mm (1.18 in.)
      Bolt C 30 mm (1.18 in.)

      Tech Tips

      Bolt B and C are identical.

    6. Tighten the 12 bolts labeled B and C.

      Torque:
      23 N*m  { 229 kgf*cm, 17 ft.*lbf }

    7. Tighten the bolt labeled A.

      Torque:
      21 N*m  { 214 kgf*cm, 15 ft.*lbf }

  4. INSTALL CRANKSHAFT PULLEY


    1. Align the keyway of the pulley with the key located on the crankshaft, then slide the pulley into place to install it.

    2. A00OQDQE01

      Using SST, install the pulley bolt.

      SST
      09213-58014   ( 91551-80840 )
      09330-00021
      Torque:
      300 N*m  { 3059 kgf*cm, 221 ft.*lbf }

  5. INSTALL WATER PUMP ASSEMBLY


    1. Remove the adhesive from the threads of the bolt and the bolt hole of the timing chain cover.

    2. A003CYU

      Install a new gasket to the timing chain cover so that the protrusions indicated by the arrows in the illustration are aligned.

    3. A003EEXE01
      Text in Illustration
      *1 Adhesive

      Apply adhesive to 2 or 3 threads of the bolt labeled A shown in the illustration.

      Standard Bolt Length
      Item Specified Condition
      Bolt A and C 45 mm (1.77 in.)
      Bolt B 30 mm (1.18 in.)
      Adhesive
      Toyota Genuine Adhesive 1324, Three Bond 1324 or equivalent
    4. A003BJB

      Install the water pump with the 2 bolts indicated by the arrows in the illustration.

      Torque:
      23 N*m  { 229 kgf*cm, 17 ft.*lbf }
    5. A003CR0

      Install the 5 bolts.

      Torque:
      23 N*m  { 229 kgf*cm, 17 ft.*lbf }

  6. CONNECT CRANKSHAFT POSITION SENSOR WIRE HARNESS


    1. A00OQZKE01
      Text in Illustration
      *1 Protrusion

      Install the sensor wire harness with the bolt and clip.

      Torque:
      8.8 N*m  { 90 kgf*cm, 78 in.*lbf }

      Note

      Make sure the sensor wire harness is installed in the position shown in the illustration.

  7. INSTALL CAMSHAFT POSITION SENSOR


    1. Apply a light coat of engine oil to the O-ring of the sensor.

      Note

      Make sure that the O-ring is not cracked or jammed when installing the sensor.

    2. A00ORM7

      Install the sensor with the bolt.

      Torque:
      8.8 N*m  { 90 kgf*cm, 78 in.*lbf }

  8. INSTALL OIL STRAINER SUB-ASSEMBLY


    1. Install a new O-ring to the oil strainer.

    2. Apply a light coat of engine oil to the O-ring.

    3. A00OU5S

      Install the oil strainer with the 3 bolts.

      Torque:
      9.0 N*m  { 92 kgf*cm, 80 in.*lbf }

  9. INSTALL OIL FILTER BRACKET


    1. A00OVJR

      Install a new gasket to the oil filter bracket.

    2. A00OSI5

      Install the oil filter bracket with the 4 bolts.

      Torque:
      9.0 N*m  { 92 kgf*cm, 80 in.*lbf }

  10. INSTALL OIL FILTER ELEMENT


    1. Clean the inside of the oil filter cap, its threads and its O-ring groove.

    2. A00E8TJE01
      Text in Illustration
      *1 New Oil Filter Element
      *2 New O-Ring

      Apply a small amount of engine oil to a new O-ring and install it to the oil filter cap.

    3. Set a new oil filter element in the oil filter cap.

    4. Remove any dirt or foreign matter from the installation surface of the engine.

    5. Apply a small amount of engine oil to the O-ring again and temporarily install the oil filter cap.

    6. A00E81EE01

      Using SST, tighten the oil filter cap.

      SST
      09228-06501
      Torque:
      40 N*m  { 408 kgf*cm, 30 ft.*lbf }

  11. INSTALL NO. 2 OIL PAN SUB-ASSEMBLY


    1. Remove any old seal packing material.

    2. A00OQN9E01

      Apply seal packing in a continuous line as shown in the illustration.

      Seal packing
      Toyota Genuine Seal Packing Black, Three Bond 1207B or equivalent
      Standard Seal Packing Dimension
      Area Seal Packing Diameter Acceptable Seal Packing Application Range
      A - A 4.0 to 7.0 mm (0.157 to 0.276 in.) 12 mm (0.472 in.)

      Note


      • Remove any oil from the contact surface.

      • Install the oil pan within 3 minutes and tighten the bolts within 10 minutes after applying seal packing.

      • Do not start the engine for at least 4 hours after installing.

    3. A00OTEXE01
      Text in Illustration
      *1 Nut

      Install the oil pan with the 18 bolts and 2 nuts.

      Torque:
      11 N*m  { 107 kgf*cm, 8 ft.*lbf }

  12. INSTALL CYLINDER HEAD COVER SUB-ASSEMBLY


    1. Remove any old seal packing material.

    2. A00OQYAE01

      Apply seal packing to the cylinder head as shown in the illustration.

      Seal packing
      Toyota Genuine Seal Packing Black, Three Bond 1207B or equivalent
      Standard Seal Packing Dimension
      Area Seal Packing Diameter Seal Packing Application Length
      A 6.0 mm (0.236 in.) 8.0 mm (0.315 in.)
      B 6.0 mm (0.236 in.) 10 mm (0.394 in.)
    3. A00OV6ZE01
      Text in Illustration
      *1 Cylinder Head Cover Gasket
      *2 No. 2 Cylinder Head Cover Gasket

      Install a new cylinder head cover gasket and new No. 2 cylinder head cover gasket to the cylinder head cover.

      Note

      Make sure the gaskets are not twisted and are not improperly seated on the cylinder head cover.

    4. A00ORC4E01
      Text in Illustration
      *1 Bolt
      *2 Nozzle Holder Clamp Seat
      *3 Nut

      Install the cylinder head cover with the 4 nozzle holder clamp seats, 14 bolts and nut.

      Torque:
      for nozzle holder clamp seat
      16 N*m  { 167 kgf*cm, 12 ft.*lbf }
      for bolt and nut
      11 N*m  { 112 kgf*cm, 8 ft.*lbf }

  13. INSTALL OIL FILLER CAP SUB-ASSEMBLY

  14. INSTALL VENTILATION HOSE

    Tech Tips

    The direction of the hose clamp is indicated in the illustration.

    A00ORCQE01

  15. INSTALL VACUUM SWITCHING VALVE BRACKET


    1. A00ORBC

      Install the vacuum switching valve bracket with the 5 bolts.

      Torque:
      9.0 N*m  { 92 kgf*cm, 80 in.*lbf }

    2. Connect the 2 vacuum hoses.

  16. INSTALL NO. 1 VACUUM TRANSMITTING PIPE SUB-ASSEMBLY


    1. A00ORKZ

      Install the No. 1 vacuum transmitting pipe with the bolt.

      Torque:
      9.0 N*m  { 92 kgf*cm, 80 in.*lbf }

    2. Connect the 2 vacuum hoses.

  17. INSTALL INJECTOR ASSEMBLY

    Note

    Before installing the injector, check for carbon, foreign matter, etc. on the seal surfaces of the cylinder head and injector. If there is foreign matter, remove it before installing the injector.


    1. Install 4 new nozzle seats to the cylinder head.

    2. A003BRLE01
      Text in Illustration
      *1 New O-Ring

      Install a new O-ring to each injector.

    3. Apply a light coat of engine oil to the O-rings on each injector.

    4. Install the 4 injectors to the cylinder head.

      Note

      Fit the injectors to the nozzle seats.

    5. A003AV0E01
      Text in Illustration
      *1 Washer

      Install the nozzle holder clamps and washers as shown in the illustration.

      Note

      Pay attention to the mounting orientation (beveled edge) of the washer.

    6. Temporarily install the nozzle holder clamp bolts.

      Note

      When temporarily attaching the nozzle holder clamp and the nozzle holder clamp bolt, be careful not to position them at an angle.

      Tech Tips

      Apply a light coat of engine oil on the threads of the nozzle holder clamp bolts.

    7. Temporarily install the 4 injection pipes.

    8. Temporarily install the No. 1 leakage pipe with 4 new gaskets, the 4 union bolts and bolt.

    9. Tighten the 4 nozzle holder clamp bolts.

      Torque:
      25 N*m  { 255 kgf*cm, 18 ft.*lbf }

  18. INSTALL NO. 1 NOZZLE LEAKAGE PIPE


    1. A003D2W

      Tighten the 4 union bolts.

      Torque:
      18 N*m  { 184 kgf*cm, 13 ft.*lbf }

    2. Tighten the bolt.

      Torque:
      21 N*m  { 209 kgf*cm, 15 ft.*lbf }

  19. INSTALL NO. 2 NOZZLE LEAKAGE PIPE


    1. A00OVZOE01
      Text in Illustration
      *1 Check Valve

      Temporarily install the No. 2 nozzle leakage pipe and a new gasket with the check valve and bolt.

    2. Tighten the check valve.

      Torque:
      32 N*m  { 321 kgf*cm, 23 ft.*lbf }

    3. Tighten the bolt.

      Torque:
      32 N*m  { 321 kgf*cm, 23 ft.*lbf }

  20. INSTALL NO. 3 FUEL HOSE

    A00ORMT

  21. INSTALL FUEL TUBE SUB-ASSEMBLY


    1. A003D04E01
      Text in Illustration
      *1 Check Valve

      Temporarily install the fuel tube and 2 new gaskets with the check valve and union bolt.

    2. Tighten the check valve.

      Torque:
      32 N*m  { 321 kgf*cm, 23 ft.*lbf }

    3. Tighten the union bolt.

      Torque:
      23 N*m  { 235 kgf*cm, 17 ft.*lbf }
    4. A003C5C

      Connect the fuel tube connector to the injector.

    5. A003DXDE01
      Text in Illustration
      *1 Fuel Tube Connector
      *2 Injector
      *3 Retainer
      *4 O-Ring

      Turn the retainer in the direction indicated by the arrow until it makes a "click" sound.

      Note

      If the fuel tube connector is not inserted to the correct position on the injector, the retainer cannot be turned far enough in the direction of the arrow.

    6. A003CV6

      Connect the exhaust fuel addition injector connector.

  22. INSTALL FUEL HOSE PROTECTOR


    1. A003BGR

      Install the fuel hose protector with the bolt.

      Torque:
      21 N*m  { 209 kgf*cm, 15 ft.*lbf }

  23. INSTALL WATER INLET HOUSING


    1. A00OR7J

      Install a new gasket and the inlet housing with the 3 nuts.

      Torque:
      9.0 N*m  { 92 kgf*cm, 80 in.*lbf }

  24. INSTALL NO. 4 WATER BY-PASS HOSE

    A00ORW3

  25. INSTALL NO. 2 WATER BY-PASS PIPE


    1. A00OUK0

      Install the No. 2 water by-pass pipe with the 2 bolts.

      Torque:
      11 N*m  { 112 kgf*cm, 8 ft.*lbf }

  26. INSTALL NO. 1 OIL COOLER BRACKET


    1. A00OUNIE02

      Apply engine oil to the 2 new O-rings labeled B in the illustration.

      Note

      Do not apply engine oil to the new O-ring labeled A in the illustration.

    2. Install 3 new O-rings to the oil cooler bracket.

    3. A00OSG8E01
      Text in Illustration
      *1 Nut

      Install the No. 1 oil cooler bracket with the 6 bolts and nut.

      Torque:
      11 N*m  { 112 kgf*cm, 8 ft.*lbf }

  27. INSTALL NO. 1 TURBO OIL PIPE


    1. A00OTJJE01
      Text in Illustration
      *1 Gasket

      Install the No. 1 turbo oil pipe and 2 new gaskets with the 2 union bolts.

      Torque:
      35 N*m  { 357 kgf*cm, 26 ft.*lbf }

      Note

      Make sure the gasket of union bolt A contacts the No. 1 turbo oil pipe as shown in the illustration when tightening the union bolt.

  28. INSTALL NO. 3 WATER BY-PASS PIPE


    1. Apply soapy water to a new O-ring and install it to the No. 3 water by-pass pipe.

    2. A00OT1M

      Install the No. 3 water by-pass pipe with the 2 bolts.

      Torque:
      21 N*m  { 214 kgf*cm, 15 ft.*lbf }

  29. INSTALL NO. 8 WATER BY-PASS HOSE

    A00OR5P

  30. INSTALL NO. 6 WATER BY-PASS HOSE

    A00OUJ2

  31. INSTALL OIL COOLER ASSEMBLY


    1. A003ATTE01

      Apply engine oil to the 2 new O-rings labeled B in the illustration.

      Note

      Do not apply engine oil to the new O-ring labeled A in the illustration.

    2. Install 3 new O-rings to the oil cooler bracket.

    3. A003DKC

      Install the oil cooler with the 5 bolts.

      Torque:
      11 N*m  { 112 kgf*cm, 8 ft.*lbf }

  32. INSTALL WATER BY-PASS HOSE

    Tech Tips

    Make sure the claws of hose clamp A are positioned above the paint mark as shown in the illustration.

    A003DA0E01

  33. INSTALL NO. 1 CYLINDER BLOCK INSULATOR


    1. A00OV0J

      Install the No. 1 cylinder block insulator to the cylinder block.

      Note

      Be sure to install the oil cooler before installing the No. 1 cylinder block insulator.

  34. INSTALL INTAKE MANIFOLD


    1. A003EHNE01

      Install a new gasket to the cylinder head.

      Tech Tips

      Install the gasket with the part labeled A facing the right side of the vehicle as shown in the illustration.

    2. A003DELE02
      Text in Illustration
      *1 Nut

      Install the intake manifold with the 7 bolts and 2 nuts.

      Torque:
      23 N*m  { 235 kgf*cm, 17 ft.*lbf }
      Bolt Length
      Item Specified Condition
      Bolt A 90 mm (3.54 in.)
      Bolt B 25 mm (0.984 in.)

  35. INSTALL NO. 2 INTAKE MANIFOLD


    1. A003DE3

      Install a new gasket and the No. 2 intake manifold with the bolt and 2 nuts.

      Torque:
      24 N*m  { 245 kgf*cm, 18 ft.*lbf }

  36. INSTALL ENGINE COVER BRACKET


    1. A003EJ9

      Install the engine cover bracket with the bolt.

      Torque:
      20 N*m  { 204 kgf*cm, 15 ft.*lbf }

  37. INSTALL GAS FILTER BRACKET


    1. A003AWW

      Install the gas filter bracket with the 2 bolts.

      Torque:
      8.8 N*m  { 90 kgf*cm, 78 in.*lbf }

  38. INSTALL NO. 1 GAS FILTER


    1. A003BCNE01
      Text in Illustration
      *1 Protrusion
      *2 Groove

      Install the No. 1 gas filter to the gas filter bracket.

      Note

      Make sure the protrusion of the No. 1 gas filter is aligned with the groove of the gas filter bracket.

    2. Connect the vacuum hose.

  39. INSTALL DIESEL TURBO PRESSURE SENSOR


    1. A00OU7HE01
      Text in Illustration
      *1 Protrusion

      Install the sensor with the bolt.

      Torque:
      8.8 N*m  { 90 kgf*cm, 78 in.*lbf }

      Note

      Make sure the protrusion of the gas filter bracket is inserted into the hole of the sensor.

    2. Connect the vacuum hose.

  40. INSTALL INTAKE MANIFOLD INSULATOR


    1. A003CC9

      Install the intake manifold insulator to the intake manifold.

  41. INSTALL COMMON RAIL ASSEMBLY


    1. A00OS2W

      Install the common rail with the 2 bolts.

      Torque:
      21 N*m  { 209 kgf*cm, 15 ft.*lbf }

  42. INSTALL NO. 4 FUEL HOSE

    A00OSTV

  43. INSTALL INJECTION PIPE SUB-ASSEMBLY


    1. A003C13

      Using a 14 mm union nut wrench, tighten the 4 nuts at the common rail end of the injection pipes.

      Torque:
      30 N*m  { 306 kgf*cm, 22 ft.*lbf }

      Note

      Use the formula to calculate special torque values for situations where a union nut wrench is combined with a torque wrench Click here.

    2. Using a 14 mm union nut wrench, tighten the 4 nuts at the injector end of the injection pipes.

      Torque:
      30 N*m  { 306 kgf*cm, 22 ft.*lbf }

      Note

      Use the formula to calculate special torque values for situations where a union nut wrench is combined with a torque wrench Click here.

    3. Install the 4 injection pipe clamps with the 2 bolts.

      Torque:
      5.0 N*m  { 51 kgf*cm, 44 in.*lbf }

  44. INSTALL FUEL INLET PIPE SUB-ASSEMBLY


    1. A003B35

      Temporarily install the fuel inlet pipe with the 2 clamps and nut.

    2. Using a 14 mm union nut wrench, first tighten the nut at the common rail end of the fuel inlet pipe.

      Torque:
      30 N*m  { 306 kgf*cm, 22 ft.*lbf }

      Note

      Use the formula to calculate special torque values for situations where a union nut wrench is combined with a torque wrench Click here.

    3. Using a 14 mm union nut wrench, tighten the nut at the supply pump end of the fuel inlet pipe.

      Torque:
      30 N*m  { 306 kgf*cm, 22 ft.*lbf }

      Note

      Use the formula to calculate special torque values for situations where a union nut wrench is combined with a torque wrench Click here.

    4. Tighten the No. 2 injection pipe clamp nut.

      Torque:
      5.0 N*m  { 51 kgf*cm, 44 in.*lbf }

  45. INSTALL ENGINE OIL LEVEL DIPSTICK GUIDE


    1. Install a new O-ring to the engine oil level dipstick guide.

    2. A00OQW3

      Install the engine oil level dipstick guide with the 2 bolts.

      Torque:
      33 N*m  { 337 kgf*cm, 24 ft.*lbf }

    3. Install the engine oil level dipstick.

  46. INSTALL ELECTRIC EGR CONTROL VALVE ASSEMBLY


    1. A006TUJE01
      Text in Illustration
      *1 Protrusion

      Install a new gasket.

      Note

      Make sure the protrusion of the gasket is facing upward as shown in the illustration.

    2. A006UZM

      Install the electric EGR control valve.

  47. INSTALL NO. 2 EGR PIPE SUB-ASSEMBLY


    1. Install a new gasket to the electric EGR control valve.

    2. Install a new gasket to the No. 2 EGR pipe.

    3. A006VT0E06
      Text in Illustration
      *1 Nut

      Temporarily install the No. 2 EGR pipe with the 3 bolts and 2 nuts.

      Bolt Length
      Item Specified Condition
      Bolt A 25 mm (0.984 in.)
      Bolt B 70 mm (2.76 in.)

    4. Tighten the 2 bolts labeled A shown in the illustration.

      Torque:
      24 N*m  { 245 kgf*cm, 18 ft.*lbf }

    5. Tighten the bolt labeled B and 2 nuts shown in the illustration.

      Torque:
      24 N*m  { 245 kgf*cm, 18 ft.*lbf }
    6. A006VQF

      Connect the electric EGR control valve connector.

  48. INSTALL EGR VALVE BRACKET


    1. A00ORPA

      Install the 2 EGR valve brackets with the 3 bolts.

      Torque:
      24 N*m  { 245 kgf*cm, 18 ft.*lbf }

  49. CONNECT NO. 8 WATER BY-PASS HOSE

    A006VPZ

  50. INSTALL NO. 7 WATER BY-PASS HOSE

    A003C0A

  51. INSTALL DIESEL THROTTLE BODY ASSEMBLY


    1. A00OSP8

      Install a new gasket and the diesel throttle body with the 2 bolts and 2 nuts.

      Torque:
      11 N*m  { 112 kgf*cm, 8 ft.*lbf }
    2. A00OQTYE01
      Text in Illustration
      *1 No. 6 Water By-pass Hose
      *2 No. 7 Water By-pass Hose

      Connect the No. 6 and No. 7 water by-pass hoses.

  52. INSTALL V-RIBBED BELT TENSIONER ASSEMBLY


    1. A00OTNN

      Install the V-ribbed belt tensioner with the 3 bolts.

      Torque:
      20 N*m  { 204 kgf*cm, 15 ft.*lbf }

      Note

      As the heads of the bolts are not as thick as those of typical bolts, be careful not to damage them during installation.

  53. INSTALL ENGINE MOUNTING BRACKET


    1. Temporarily install the engine mounting bracket with the 2 bolts labeled A.

    2. A00OQMXE01

      Temporarily install the 2 bolts and 2 nuts labeled B in the illustration.

    3. Tighten the 2 bolts labeled A in the illustration.

      Torque:
      28 N*m  { 286 kgf*cm, 21 ft.*lbf }

    4. Tighten the 2 bolts and 2 nuts labeled B in the illustration.

      Torque:
      80 N*m  { 816 kgf*cm, 59 ft.*lbf }

  54. INSTALL NO. 4 WATER BY-PASS PIPE


    1. Install a new O-ring to the No. 4 water by-pass pipe.

    2. A00ORNB

      Install the No. 4 water by-pass pipe with the bolt.

      Torque:
      11 N*m  { 112 kgf*cm, 8 ft.*lbf }

  55. INSTALL NO. 2 IDLER PULLEY SUB-ASSEMBLY


    1. A00ORZEE01
      Text in Illustration
      *1 No. 2 Idler Pulley Cover Plate
      *2 No. 2 Idler Pulley

      Install the No. 2 idler pulley and No. 2 idler pulley cover plate with the bolt.

      Torque:
      40 N*m  { 408 kgf*cm, 30 ft.*lbf }

      Note

      Make sure the No. 2 idler pulley cover plate is facing the direction shown in the illustration.

  56. INSTALL NO. 1 IDLER PULLEY SUB-ASSEMBLY


    1. A00ORP0

      Install the No. 1 idler pulley with the bolt.

      Torque:
      40 N*m  { 408 kgf*cm, 30 ft.*lbf }

  57. INSTALL IDLER PULLEY COVER PLATE


    1. A00OQKS

      Install the idler pulley cover plate to the No. 1 idler pulley.

  58. INSTALL VACUUM PUMP ASSEMBLY


    1. Apply a light coat of engine oil to 2 new O-rings.

    2. Install the 2 O-rings to the vacuum pump.

    3. A00ORBQ

      Install the vacuum pump with new 3 bolts.

      Torque:
      21 N*m  { 214 kgf*cm, 15 ft.*lbf }

    4. Connect the vacuum hose.

  59. INSTALL GENERATOR ASSEMBLY


    1. A00OV15

      Install the generator with the 3 bolts.

      Torque:
      25 N*m  { 255 kgf*cm, 18 ft.*lbf }

  60. CONNECT ENGINE WIRE


    1. Connect the connectors and clamps, and then connect the engine wire to the engine with the bracket bolts.

  61. INSTALL ENGINE ASSEMBLY


    1. Install the engine assembly Click here.