SPEED SENSOR INSTALLATION


  1. INSTALL SPEED SENSOR

    A006T9QE01

    1. Coat the 2 bolts with ATF.

    2. Install the speed sensor to the valve body with the 2 bolts.

      Torque:
      11 N*m  { 110 kgf*cm, 8 ft.*lbf }

    3. Connect the connector.

  2. INSTALL TRANSMISSION VALVE BODY ASSEMBLY


    1. Coat the O-ring of the transmission wire connector with ATF.

    2. Align the groove of the manual valve with the manual valve lever.

    3. A00E7MJE02

      Install the valve body to the transaxle case with the 11 bolts.

      Note


      • When installing the transmission valve body assembly, be careful not to allow the transmission revolution sensor and transaxle case to interfere with each other.

      • Temporarily install the bolts marked *1 in the illustration first because they are positioning bolts.

      Torque:
      11 N*m  { 110 kgf*cm, 8 ft.*lbf }

      Tech Tips

      Each bolt length is indicated below.

      Bolt A: 25 mm (0.984 in.)

      Bolt B: 30 mm (1.18 in.)

      Bolt C: 35 mm (1.38 in.)

      Bolt D: 45 mm (1.77 in.)

      Bolt E: 55 mm (2.17 in.)

  3. INSTALL VALVE BODY OIL STRAINER ASSEMBLY

    A00E8TD

    1. Coat a new O-ring with ATF and install it to the oil strainer.

      Note

      Ensure that the O-ring is not twisted or pinched.

    2. A00E80G

      Install the oil strainer to the valve body with the 2 bolts.

      Torque:
      11 N*m  { 110 kgf*cm, 8 ft.*lbf }

  4. INSTALL AUTOMATIC TRANSAXLE OIL PAN SUB-ASSEMBLY

    A00E713E05

    1. Install the 2 magnets to the oil pan.

      Text in Illustration
      *1 Magnet

    2. Install a new gasket to the oil pan.

    3. A00E9GSE01

      Apply seal packing to the bolt labeled A in the illustration.

      Seal packing
      Toyota Genuine Seal Packing 1281,
      Three Bond 1281 or equivalent

    4. Install the oil pan to the automatic transaxle with the 18 bolts.

      Torque:
      for bolt labeled A
      7.0 N*m  { 71 kgf*cm, 62 in.*lbf }
      for other bolts
      7.5 N*m  { 76 kgf*cm, 66 in.*lbf }

      Note


      • In order to ensure proper sealing of the transmission oil pan bolt, apply seal packing to the bolt and install it within 10 minutes of seal packing application.

      • Completely remove any oil or grease from the contact surfaces of the transaxle case, oil pan sub-assembly and gasket before installation.

  5. INSTALL FRONT SUSPENSION MEMBER REINFORCEMENT LH

    A00EA6F

    1. Install the front suspension member reinforcement with the 4 bolts.

      Torque:
      96 N*m  { 979 kgf*cm, 71 ft.*lbf }

  6. ADD AUTOMATIC TRANSAXLE FLUID


    1. Add automatic transaxle fluid Click here.

  7. INSTALL REAR ENGINE UNDER COVER LH


    1. Install the under cover with the 5 clips.

  8. INSTALL NO. 1 ENGINE UNDER COVER


    1. A00EB0Y

      Install the engine under cover with the 11 clips.

  9. INSTALL FRONT LOWER BUMPER ABSORBER


    1. A00E73K

      Insert the 2 hooks of the front lower bumper absorber into the installation holes on the body to install the front lower bumper absorber .

    2. Install 8 bolts and 3 screws.

    3. A00E7US

      Install the 4 screws and 2 bolts.