AUTOMATIC TRANSAXLE SYSTEM Shift Paddle Switch Circuit

DESCRIPTION

When the shift lever is in M, the shift range can be changed using the shift paddle switches. It is also possible to select the shift range when the vehicle is being driven with the shift lever in D by operating the shift paddle switches.

WIRING DIAGRAM

A006UIGE01

INSPECTION PROCEDURE

PROCEDURE


  1. CHECK HARNESS AND CONNECTOR (SPIRAL CABLE - BODY GROUND)


    1. A006UW4E01
      Text in Illustration
      *1

      Front view of wire harness connector

      (to Spiral Cable Sub-assembly)

      Disconnect the spiral cable connector.

    2. Measure the resistance according to the value(s) in the table below.

      Standard Resistance
      Tester Connection Condition Specified Condition
      D5-2 (ECC) - Body ground Always Below 1 Ω

    NG

    REPAIR OR REPLACE HARNESS OR CONNECTOR

    OK

  2. INSPECT SPIRAL CABLE SUB-ASSEMBLY


    1. A006VF8E01
      Text in Illustration
      *1

      Component without harness connected

      (Spiral Cable Sub-assembly)

      Remove the spiral cable sub-assembly Click here.

    2. Measure the resistance according to the value(s) in the table below.

      Standard Resistance
      Tester Connection Condition Specified Condition
      z6-2 (SUP) - D5-9 (SUP) Always Below 1 Ω
      z6-3 (SDN) - D5-10 (SDN) Always Below 1 Ω
      z6-6 (ECC) - D5-2 (ECC) Always Below 1 Ω

    NG

    REPLACE SPIRAL CABLE SUB-ASSEMBLY Click here

    OK

  3. INSPECT TRANSMISSION SHIFT SWITCH ASSEMBLY (LH (-) AND RH (+))


    1. A006VBOE01
      Text in Illustration
      *1

      Component without harness connected

      (Transmission Shift Switch Assembly)
      *2 for LH
      *3 for RH

      Remove the transmission shift switch assembly Click here.

    2. Measure the resistance according to the value(s) in the table below.

      Standard Resistance
      for LH
      Tester Connection Switch Condition Specified Condition
      SDN - ECC "-" shift paddle operated and held (down-shift) Below 2.5 Ω
      SDN - ECC "-" shift paddle not operated (down-shift) 1 MΩ or higher
      for RH
      Tester Connection Switch Condition Specified Condition
      SUP - ECC "+" shift paddle operated and held (up-shift) Below 2.5 Ω
      SUP - ECC "+" shift paddle not operated (up-shift) 1 MΩ or higher

    NG

    REPLACE TRANSMISSION SHIFT SWITCH ASSEMBLY Click here

    OK

  4. INSPECT NO. 1 SWITCH WIRE


    1. A006TIIE01
      Text in Illustration
      *1

      Component without harness connected

      (No. 1 Switch Wire)

      Disconnect the No. 1 switch wire connector.

    2. Measure the resistance according to the value(s) in the table below.

      Standard Resistance
      Tester Connection Switch Condition Specified Condition
      SDN - ECC "-" shift paddle operated and held (down-shift) Below 2.5 Ω
      SUP - ECC "+" shift paddle operated and held (up-shift) Below 2.5 Ω
      SDN - ECC "-" shift paddle not operated (down-shift) 1 MΩ or higher
      SUP - ECC "+" shift paddle not operated (up-shift) 1 MΩ or higher

    NG

    REPLACE NO. 1 SWITCH WIRE Click here

    OK

  5. INSPECT STEERING PAD SWITCH ASSEMBLY


    1. A006VGUE01
      Text in Illustration
      *1

      Front view of wire harness connector

      (to Spiral Cable Sub-assembly)

      Disconnect the steering pad switch assembly connector.

    2. Measure the resistance according to the value(s) in the table below.

      Standard Resistance
      Tester Connection Switch Condition Specified Condition
      z6-2 (SUP) - z6-6 (ECC) "+" shift paddle operated and held (up-shift) Below 2.5 Ω
      z6-3 (SDN) - z6-6 (ECC) "-" shift paddle operated and held (down-shift) Below 2.5 Ω
      z6-2 (SUP) - z6-6 (ECC) "+" shift paddle not operated (up-shift) 1 MΩ or higher
      z6-3 (SDN) - z6-6 (ECC) "-" shift paddle not operated (down-shift) 1 MΩ or higher

    NG

    REPLACE STEERING PAD SWITCH ASSEMBLY Click here

    OK

  6. CHECK HARNESS AND CONNECTOR (SPIRAL CABLE - ECM)


    1. A006WJHE10
      Text in Illustration
      *1

      Front view of wire harness connector

      (to ECM)

      Disconnect the ECM connector.

    2. Disconnect the transmission control switch (shift lock control unit assembly) connector.

    3. Measure the resistance according to the value(s) in the table below.

      Standard Resistance
      Tester Connection Switch Condition Specified Condition
      A40-19 (SFTU) - Body ground "+" shift paddle operated and held (up-shift) Below 2.5 Ω
      A40-28 (SFTD) - Body ground "-" shift paddle operated and held (down-shift) Below 2.5 Ω
      A40-19 (SFTU) - Body ground "+" shift paddle not operated (up-shift) 1 MΩ or higher
      A40-28 (SFTD) - Body ground "-" shift paddle not operated (down-shift) 1 MΩ or higher

    NG

    REPAIR OR REPLACE HARNESS OR CONNECTOR

    OK

    PROCEED TO NEXT SUSPECTED AREA SHOWN IN PROBLEM SYMPTOMS TABLE Click here