МАСЛО И МАСЛЯНЫЙ ФИЛЬТР ЗАМЕНА

CAUTION:

  • Prolonged and repeated contact with engine oil will cause removal of natural oils from the skin, leading to dryness, irritation and dermatitis. In addition, used engine oil contains potentially harmful contaminants which may cause skin cancer.

  • Precautions should be taken when replacing engine oil to minimize the risk of your skin making contact with used engine oil. Wear protective clothing and gloves. Wash your skin thoroughly with soap and water, or use a waterless hand cleaner to remove any used engine oil. Do not use gasoline, thinners or solvents.

  • For environmental protection, used oil and used oil filters must be disposed of at designated disposal sites.

  1. DRAIN ENGINE OIL

    1. Remove the oil filler cap.

    2. Remove the 3 clips and open the oil pan drain service cover.

    3. Remove the oil pan drain plug and gasket, and drain the engine oil into a container.

  2. REMOVE OIL FILTER CAP ASSEMBLY

    1. Using SST, loosen the oil filter cap 4 revolutions, align the cap ribs vertically, and drain the remaining engine oil in the oil filter cap.

      A00DU0YE01
      SST
      09228-06501
      Text in Illustration
      *1 Cap Rib
      *2 Oil Filter Bracket Clip

      Tech Tips

      Set a container below the oil filter cap before loosening the oil filter cap.

      Note

      Do not remove the oil filter bracket clip when removing the oil filter cap assembly.

    2. Remove the oil filter cap.

    3. Remove the oil filter element and O-ring from the oil filter cap.

      A00DSFLE01
      Text in Illustration
      *1 Oil Filter Element
      *2 O-Ring

      Note

      Be sure to remove the O-ring (for the cap) by hand, without using any tools, to prevent damage to the groove for the O-ring on the cap.

  3. INSTALL OIL FILTER CAP ASSEMBLY

    1. Clean the inside of the oil filter cap, its threads and O-ring groove.

      A00DSFLE02

    2. Apply a small amount of engine oil to a new O-ring and install it to the oil filter cap.

      Text in Illustration
      *1 O-Ring

    3. Set a new oil filter element in the oil filter cap.

    4. Remove any dirt or foreign matter from the installation surface and inside of the engine.

    5. Reapply a small amount of engine oil to the O-ring of the oil filter cap. Align the oil filter cap with the oil filter bracket so that the cutout portion of the cap threads is in a position 90° from the groove in the bracket, and then temporarily install the cap.

      Note

      Make sure that the O-ring does not get caught between the parts.

      A00DQMA

    6. Using SST, tighten the oil filter cap.

      A00DUJEE01
      SST
      09228-06501
      Torque:
      25 N*m  { 255 kgf*cm, 18 ft.*lbf }

      Note

      • After tightening the oil filter cap, check for gaps between the installation surfaces.

      • Do not remove the oil filter bracket clip when installing the oil filter cap.

      • Do not cross thread the oil filter cap.

  4. ADD ENGINE OIL

    1. Clean and install the oil pan drain plug together with a new gasket.

      Torque:
      37 N*m  { 377 kgf*cm, 27 ft.*lbf }

    2. Add new engine oil.

      Standard Oil Grade
      Oil Grade Oil Viscosity (SAE)
      API grade SL or SM multigrade engine oil

      • 15W-40

      • 20W-50
      API grade SL "Energy-Conserving", SM "Energy-Conserving" or ILSAC multigrade engine oil

      • 0W-20

      • 5W-20

      • 5W-30

      • 10W-30
      Standard Capacity
      Item Specified Condition
      Drain and refill without oil filter change 3.9 liters (4.1 US qts, 3.4 Imp. qts)
      Drain and refill with oil filter change 4.2 liters (4.4 US qts, 3.7 Imp. qts)
      Dry fill 4.7 liters (5.0 US qts, 4.1 Imp. qts)

    3. Install the oil filler cap.

  5. INSPECT FOR OIL LEAK

    1. Start the engine. Make sure that there are no oil leaks from the areas that were worked on.

  6. INSPECT ENGINE OIL LEVEL

    1. Прогрейте двигатель, а затем остановите его и подождите 5 мин.

    2. Убедитесь, что уровень масла находится между отметками низкого и максимального уровней на щупе проверки уровня масла.

      Если уровень масла находится на низком уровне, убедитесь в отсутствии утечек моторного масла и долейте масло до максимальной отметки.

      Note

      Не заливайте моторное масло выше максимальной отметки.