ДАТЧИК ТЕМПЕРАТУРЫ ОХЛАЖДАЮЩЕЙ ЖИДКОСТИ УСТАНОВКА

  1. INSTALL ENGINE COOLANT TEMPERATURE SENSOR

    1. A00DQPBE01

      Install a new gasket to the sensor.

    2. Using SST, install the sensor.

      SST
      09817-33190
      Torque:
      20 N*m  { 204 kgf*cm, 15 ft.*lbf }
    3. A00DUJ1

      Connect the sensor connector.

  2. INSTALL AIR CLEANER CASE SUB-ASSEMBLY

    1. A00DQ1D

      Install the air cleaner case with the 3 bolts.

      Torque:
      7.0 N*m  { 71 kgf*cm, 62 in.*lbf }

    2. Attach the wire harness clamp to the air cleaner case.

  3. INSTALL AIR CLEANER CAP SUB-ASSEMBLY

    1. Подсоедините крышку воздушного фильтра с помощью хомута.

      A005W5Q

    2. Подключите вентиляционный шланг.

    3. Подсоедините 2 зажима.

      A005U5E
    4. A005UEV

      Закрепите жгут проводов с помощью 2 зажимов.

    5. Подключите разъем датчика массового расхода воздуха.

  4. INSTALL NO. 2 CYLINDER HEAD COVER

    1. A005VFG

      Установите крышку и введите в зацепление 4 фиксатора.

      Note

      • Проверьте надежность зацепления фиксаторов.

      • Во время зацепления фиксаторов на крышке не прикладывайте чрезмерных усилий и не допускайте ударов. Это может привести к поломке крышки.

  5. ADD ENGINE COOLANT

    1. Tighten the radiator drain cock plug.

    2. Tighten the cylinder block drain cock plug.

      Torque:
      13 N*m  { 130 kgf*cm, 9 ft.*lbf }
    3. A005VD2

      Add TOYOTA Super Long Life Coolant (SLLC) through the radiator reservoir filler opening until the coolant reaches the B line.

      Standard Capacity
      Item Specified Condition
      for Manual Transaxle 6.3 liters (6.7 US qts, 5.5 Imp. qts)
      for Automatic Transaxle 6.2 liters (6.6 US qts, 5.4 Imp. qts)

      Tech Tips

      TOYOTA vehicles are filled with TOYOTA SLLC at the factory. In order to avoid damage to the engine cooling system and other technical problems, only use TOYOTA SLLC or similar high quality ethylene glycol based non-silicate, non-amine, non-nitrite, non-borate coolant with long-life hybrid organic acid technology (coolant with long-life hybrid organic acid technology is a combination of low phosphates and organic acids).

      Note

      Never use water as a substitute for engine coolant.

    4. Squeeze the inlet and outlet radiator hoses several times by hand, and then check the level of the coolant.

      If the coolant level is low, add coolant.

    5. Install the cap and warm up the engine sufficiently.

    6. Bleed air from the cooling system.

      Note

      • Before starting the engine, turn the A/C switch off.

      • Adjust the air conditioning temperature setting to MAX (HOT).

      • Adjust the air conditioning blower setting to Lo.

      1. Warm up the engine until the thermostat opens. While the thermostat is open, allow the coolant to circulate for several minutes.

        Tech Tips

        The thermostat opening timing can be confirmed by squeezing the inlet radiator hose by hand, and sensing vibrations when the engine coolant starts to flow inside the hose.

        CAUTION:

        When squeezing the radiator hose:

        • Wear protective gloves.

        • Be careful as the radiator hoses are hot.

        • Keep your hands away from the radiator fan.

      2. After the engine has warmed up, repeat the following procedure for at least 7 minutes: run the engine at 3000 rpm for 5 seconds, and then at idle speed for 45 seconds (repeat this procedure at least 8 times).

      3. Squeeze the inlet and outlet radiator hoses several times by hand to bleed air from the system.

        CAUTION:

        When squeezing the radiator hose:

        • Wear protective gloves.

        • Be careful as the radiator hoses are hot.

        • Keep your hands away from the radiator fan.

    7. After the engine has cooled down, check that the coolant level is between FULL and LOW lines.

      A005VD2

      If the coolant level is low, add coolant to the FULL line on the reservoir.

  6. INSPECT FOR COOLANT LEAK

    CAUTION:

    Во избежание ожогов не снимайте крышку расширительного бачка радиатора, пока двигатель и радиатор не остынут. Тепловое расширение может вызвать выброс из радиатора горячей охлаждающей жидкости и пара.

    1. Заполните радиатор охлаждающей жидкостью, а затем подсоедините приспособление для опрессовки системы охлаждения и проверки пробки радиатора.

      A005TAG

    2. Прогрейте двигатель.

    3. С помощью приспособления для опрессовки системы охлаждения и проверки пробки радиатора увеличьте давление в радиаторе до 118 кПа (1,2 кгс/см2, 17 фунтов на кв. дюйм) и убедитесь, что давление не падает.

      Если давление снижается, проверьте на наличие утечек шланги, радиатор и насос системы охлаждения. Если нет следов или признаков утечки внешней охлаждающей жидкости, проверьте сердцевину отопителя, блок цилиндров и головку блока цилиндров.

  7. INSTALL RADIATOR SUPPORT OPENING COVER

    1. Install the radiator support opening cover with the 8 clips.

      A00DRS1

  8. INSTALL ENGINE ROOM SIDE COVER

    1. Install the engine room side cover with the clip.

      A00DRIG