ТРОС МЕХАНИЗМА ПЕРЕКЛЮЧЕНИЯ ПЕРЕДАЧ СНЯТИЕ

  1. REMOVE RADIATOR SUPPORT OPENING COVER

    1. Remove the 7 clips and radiator support opening cover.

      A00OKW2

  2. REMOVE NO. 2 CYLINDER HEAD COVER

    1. A010LIT

      Hold the rear of the cover and raise it to detach the 2 clips on the rear of the cover. Continue to raise the cover to detach the 2 clips on the front of the cover and remove the cover.

      Note

      Attempting to detach both front and rear clips at the same time may cause the cover to break.

  3. PRECAUTION

    Note

    After turning the ignition switch off, waiting time may be required before disconnecting the cable from the battery terminal. Therefore, make sure to read the disconnecting the cable from the battery terminal notice before proceeding with work Click here.

  4. DISCONNECT CABLE FROM NEGATIVE BATTERY TERMINAL

    Note

    When disconnecting the cable, some systems need to be initialized after the cable is reconnected Click here.

  5. REMOVE BATTERY

    1. Disconnect the cable from the positive (+) battery terminal.

    2. Remove the bolt and loosen the nut.

    3. Remove the battery clamp.

    4. Remove the battery.

    5. Remove the battery tray.

  6. REMOVE BATTERY CARRIER

    A00OJKB

    1. Detach the 2 wire harness clamps.

    2. Remove the 4 bolts and battery carrier.

  7. REMOVE AIR CLEANER CAP AND HOSE

    1. A010KC2

      Disconnect the mass air flow meter connector.

    2. Detach the wire harness from the 2 clamps.

    3. Disconnect the 2 clamps.

      A010GFY

    4. Disconnect the ventilation hose.

      A010KPJ

    5. Loosen the band and remove the air cleaner cap.

  8. REMOVE AIR CLEANER CASE SUB-ASSEMBLY

    1. A010IG6

      Detach the wire harness clamp from the air cleaner case.

    2. Remove the 3 bolts and air cleaner case.

  9. REMOVE NO. 2 ENGINE UNDER COVER

    1. С помощью съемника фиксаторов освободите 4 фиксатора и снимите защиту картера.

      A00DUSP

  10. DISCONNECT HEATED OXYGEN SENSOR CONNECTOR

  11. REMOVE FRONT EXHAUST PIPE ASSEMBLY

    1. Выверните 2 болта и снимите 2 пружины сжатия.

      A00DRN8

    2. Снимите 2 опоры выпускной трубы и приемную трубу в сборе.

  12. REMOVE FRONT FLOOR NO. 1 HEAT INSULATOR

    A00OJ33

    1. Remove the 5 nuts and heat insulator.

  13. REMOVE CONSOLE BOX ASSEMBLY

    Click here

  14. REMOVE TRANSMISSION CONTROL CABLE ASSEMBLY

    1. Move the shift lever to N.

    2. Disconnect the end of the transmission control cable from the shift lever.

      A00OILXE01

    3. Pull out the stopper of the transmission control cable.

      A00OLG5E01
      Text in Illustration
      *1 Stopper
      *2 Nut

      Note

      Do not remove the stopper. If the stopper is removed, reinstall it to its original position.

    4. Rotate the nut counterclockwise approximately 180° and, while holding the nut in that position, disconnect the transmission control cable from the shift lever retainer.

      Note

      Do not over-rotate the nut as it will come off the internal spring and the transmission control cable will not be reusable.

    5. Remove the nut and disconnect the control cable assembly from the control shaft lever.

      A00OIO3

    6. Remove the clip and disconnect the transmission control cable from the control cable bracket.

    7. Disconnect the control cable from the transmission control cable support.

      A00ONNB

    8. Remove the bolt and disconnect the transmission control cable support.

      A00ONL5

    9. Remove the 2 nuts and disconnect the transmission control cable.

      A00ONHR

    10. Pull out the transmission control cable to remove it.