CLEARANCE LIGHT ASSEMBLY INSPECTION

PROCEDURE


  1. INSPECT CLEARANCE LIGHT HOUSING ASSEMBLY LH (for Triple Beam Headlight)


    1. Remove the clearance light assembly LH.

      Click here

    2. Remove the clearance housing assembly LH from the clearance assembly LH.

      Click here

    3. Measure the resistance according to the value(s) in the table below.

      B007467C04
      *a

      Component without harness connected

      (Clearance Light Housing Assembly LH)

      		 - -
      Standard Resistance
      Tester Connection Condition Specified Condition
      A32-1 (B) - A-5 Always Below 1 Ω
      A32-2 (E) - A-2 Always Below 1 Ω
      A32-3 (DRL) - A-4 Always Below 1 Ω
      A32-4 (DRLC) - A-3 Always Below 1 Ω

      If the result is not as specified, replace the clearance light assembly LH.

  2. INSPECT CLEARANCE LIGHT ASSEMBLY LH (for Triple Beam Headlight)


    1. A01F7GZC03
      *a

      Component without harness connected

      (Clearance Light Assembly LH)

      Apply battery voltage to the clearance light assembly LH and check the light comes on.

      OK
      Condition Specified Condition

      Battery positive (+) → 3 (DRL)

      Battery negative (-) → 2 (E) and 4 (DRLC)

      		 Light comes on

      Battery positive (+) → 1 (B)

      Battery negative (-) → 2 (E)

      		 Light comes on

      If the result is not as specified, replace the clearance light LED unit assembly.

  3. INSPECT CLEARANCE LIGHT HOUSING ASSEMBLY RH (for Triple Beam Headlight)


    1. Remove the clearance light assembly RH.

      Click here

    2. Remove the clearance housing assembly RH from the clearance assembly RH.

      Click here

    3. Measure the resistance according to the value(s) in the table below.

      A01F9S8C04
      *a

      Component without harness connected

      (Clearance Light Housing Assembly RH)

      		 - -
      Standard Resistance
      Tester Connection Condition Specified Condition
      A3-1 (B) - A-5 Always Below 1 Ω
      A3-2 (E) - A-2 Always Below 1 Ω
      A3-3 (DRL) - A-4 Always Below 1 Ω
      A3-4 (DRLC) - A-3 Always Below 1 Ω

      If the result is not as specified, replace the clearance light assembly RH.

  4. INSPECT CLEARANCE LIGHT ASSEMBLY RH (for Triple Beam Headlight)


    1. A01F7GZC04
      *a

      Component without harness connected

      (Clearance Light Assembly RH)

      Apply battery voltage to the clearance light assembly RH and check the light comes on.

      OK
      Condition Specified Condition

      Battery positive (+) → 3 (DRL)

      Battery negative (-) → 2 (E) and 4 (DRLC)

      		 Light comes on

      Battery positive (+) → 1 (B)

      Battery negative (-) → 2 (E)

      		 Light comes on

      If the result is not as specified, replace the clearance light assembly RH.

  5. INSPECT CLEARANCE LIGHT HOUSING ASSEMBLY LH (for Single Beam Headlight)


    1. Remove the clearance light assembly LH.

      Click here

    2. Remove the clearance housing assembly LH from the clearance assembly LH.

      Click here

    3. Measure the resistance according to the value(s) in the table below.

      A01F882C05
      *a

      Component without harness connected

      (Clearance Light Housing Assembly LH)

      		 - -
      Standard Resistance
      Tester Connection Condition Specified Condition
      A32-2 (E) - A-2 Always Below 1 Ω
      A32-3 (B) - A-4 Always Below 1 Ω
      A32-4 (B) - A-3 Always Below 1 Ω

      If the result is not as specified, replace the clearance light assembly LH.

  6. INSPECT CLEARANCE LIGHT ASSEMBLY LH (for Single Beam Headlight)


    1. A01F7GZC05
      *a

      Component without harness connected

      (Clearance Light Assembly LH)

      Apply battery voltage to the clearance light assembly LH and check the light comes on.

      OK
      Condition Specified Condition

      Battery positive (+) → 4 (CLL)

      Battery negative (-) → 2 (E)

      		 Light comes on

      Battery positive (+) → 3 (DRL)

      Battery negative (-) → 2 (E)

      		 Light comes on

      If the result is not as specified, replace the clearance light assembly LH.

  7. INSPECT CLEARANCE LIGHT HOUSING ASSEMBLY RH (for Single Beam Headlight)


    1. Remove the clearance light assembly RH.

      Click here

    2. Remove the clearance housing assembly RH from the clearance assembly RH.

      Click here

    3. Measure the resistance according to the value(s) in the table below.

      A01F9S8C05
      *a

      Component without harness connected

      (Clearance Light Housing Assembly RH)

      		 - -
      Standard Resistance
      Tester Connection Condition Specified Condition
      A3-2 (E) - A-2 Always Below 1 Ω
      A3-3 (B) - A-4 Always Below 1 Ω
      A3-4 (B) - A-3 Always Below 1 Ω

      If the result is not as specified, replace the clearance light assembly RH.

  8. INSPECT CLEARANCE LIGHT ASSEMBLY RH (for Single Beam Headlight)


    1. A01F7GZC06
      *a

      Component without harness connected

      (Clearance Light Assembly RH)

      Apply battery voltage to the clearance light assembly RH and check the light comes on.

      OK
      Condition Specified Condition

      Battery positive (+) → 4 (CLL)

      Battery negative (-) → 2 (E)

      		 Light comes on

      Battery positive (+) → 3 (DRL)

      Battery negative (-) → 2 (E)

      		 Light comes on

      If the result is not as specified, replace the clearance light assembly RH.