AUTOMATIC HEADLIGHT BEAM LEVEL CONTROL SYSTEM(for Single Beam Headlight), Diagnostic DTC:B241A

DTC Code DTC Name
B241A Rear Height Control Sensor

DESCRIPTION

The headlight leveling ECU assembly receives signals indicating the height of the vehicle from the rear height control sensor sub-assembly LH.

DTC No. Detection Item DTC Detection Condition Trouble Area
B241A Rear Height Control Sensor

  • Malfunction in rear height control sensor sub-assembly LH

  • Open or short in rear height control sensor sub-assembly LH circuit

  • Rear height control sensor sub-assembly LH

  • Harness or connector

  • Headlight leveling ECU assembly

WIRING DIAGRAM

B0076ZZE16
*a OUT
*b Rear Height Control Sensor Sub-assembly LH
*c Headlight Leveling ECU Assembly

CAUTION / NOTICE / HINT

Note


  • If the headlight leveling ECU assembly has been replaced, it is necessary to synchronize the vehicle information and initialize the headlight leveling ECU assembly.

    Click here

  • If any of the following are performed, it is necessary to initialize the headlight leveling ECU assembly.

    Click here


    • Replacement of the rear height control sensor sub-assembly LH

    • Removal/installation of the rear height control sensor sub-assembly LH

    • Work that changes the vehicle height such as replacement of suspension components

PROCEDURE


  1. CHECK FOR DTC


    1. Clear the DTCs.

      Click here


      Body Electrical > HL AutoLeveling > Clear DTCs

    2. Check for DTCs.

      Click here


      Body Electrical > HL AutoLeveling > Trouble Codes
      OK
      DTC B241A is not output.
      Result
      Proceed to
      OK
      NG

    OK

    USE SIMULATION METHOD TO CHECK Click here

    NG

  2. READ VALUE USING GTS


    1. Connect the GTS to the DLC3.

    2. Turn the engine switch on (IG).

    3. Turn the GTS on.

    4. Enter the following menus: Body Electrical / HL AutoLeveling / Data List.

    5. Read the Data List according to the display on the GTS.


      Body Electrical > HL AutoLeveling > Data List
      Tester Display Measurement Item Range Normal Condition Diagnostic Note
      Rr Height Sens Signal Val Rear height control sensor signal value 0.00 to 5.00 V 0.50 to 4.50 V Value changes according to vehicle height

      Body Electrical > HL AutoLeveling > Data List
      Tester Display
      Rr Height Sens Signal Val
      OK
      Normal condition listed above is displayed.
      Result
      Proceed to
      OK
      NG

    OK

    REPLACE HEADLIGHT LEVELING ECU ASSEMBLY Click here

    NG

  3. CHECK HARNESS AND CONNECTOR (HEADLIGHT LEVELING ECU ASSEMBLY - REAR HEIGHT CONTROL SENSOR SUB-ASSEMBLY LH)


    1. Disconnect the A61 headlight leveling ECU assembly connector.

    2. Disconnect the k1 rear height control sensor sub-assembly LH connector.

    3. Measure the resistance according to the value(s) in the table below.

      Standard Resistance
      Tester Connection Condition Specified Condition
      A61-19 (SHRL) - k1-2 (OUT) Always Below 1 Ω
      A61-19 (SHRL) - Body ground Always 10 kΩ or higher
      Result
      Proceed to
      OK
      NG

    NG

    REPAIR OR REPLACE HARNESS OR CONNECTOR

    OK

  4. INSPECT REAR HEIGHT CONTROL SENSOR SUB-ASSEMBLY LH


    1. Remove the rear height control sensor sub-assembly LH.

      Click here

    2. Inspect the rear height control sensor sub-assembly LH.

      Click here

      Result
      Proceed to
      OK
      NG

    OK

    REPLACE HEADLIGHT LEVELING ECU ASSEMBLY Click here

    NG

    REPLACE REAR HEIGHT CONTROL SENSOR SUB-ASSEMBLY LH Click here