AUTOMATIC HEADLIGHT BEAM LEVEL CONTROL SYSTEM(for Triple Beam Headlight) Headlight Beam Level Control Actuator Circuit

DESCRIPTION

The headlight light control ECU sub-assembly LH and RH operates the headlight leveling motors according to the vehicle conditions.

WIRING DIAGRAM

B0075TWE03

PROCEDURE


  1. PERFORM ACTIVE TEST USING GTS


    1. Connect the GTS to the DLC3.

    2. Start the engine.

    3. Turn the GTS on.

    4. Enter the following menus: Body Electrical / HL AutoLeveling / Active Test.

    5. Perform the Active Test according to the display on the GTS.


      Body Electrical > HL AutoLeveling > Active Test
      Tester Display Measurement Item Control Range Diagnostic Note
      Drive The Leveling Motor Leveling motor upward or downward operation Stop/Down/Up Perform the Active Test with the engine started and vehicle stopped

      Body Electrical > HL AutoLeveling > Active Test
      Tester Display
      Drive The Leveling Motor
      OK
      Headlight leveling motors operate normally.
      Result
      Result Proceed to
      OK A
      NG (for LH Side) B
      NG (for RH Side) C

    A
    C
    B
  2. INSPECT HEADLIGHT HOUSING ASSEMBLY LH


    1. Remove the headlight assembly LH.

      Click here

    2. Remove the headlight light control ECU sub-assembly LH.

      Click here

    3. Disconnect the headlight leveling motor LH connector.

    4. Measure the resistance according to the value(s) in the table below.

      B0077A3C03
      *a

      Component without harness connected

      (Headlight Housing Assembly LH)

      - -
      Standard Resistance
      Tester Connection Condition Specified Condition
      LVL-1 - F-17 Always Below 1 Ω
      LVL-2 - F-8 Always Below 1 Ω
      LVL-3 - F-20 Always Below 1 Ω
      Result
      Proceed to
      OK
      NG

    NG
    OK
  3. REPLACE HEADLIGHT LEVELING MOTOR LH


    1. Replace the headlight leveling motor LH with a new or known good one.

      Click here

    2. Perform the Active Test according to the display on the GTS.


      Body Electrical > HL AutoLeveling > Active Test
      Tester Display Measurement Item Control Range Diagnostic Note
      Drive The Leveling Motor Leveling motor upward or downward operation Stop/Down/Up Perform the Active Test with the engine started and vehicle stopped

      Body Electrical > HL AutoLeveling > Active Test
      Tester Display
      Drive The Leveling Motor
      OK
      Headlight leveling motor LH operate normally.
      Result
      Proceed to
      OK
      NG

    OK
    NG
  4. INSPECT HEADLIGHT HOUSING ASSEMBLY RH


    1. Remove the headlight assembly RH.

      Click here

    2. Remove the headlight light control ECU sub-assembly RH.

      Click here

    3. Disconnect the headlight leveling motor RH connector.

    4. Measure the resistance according to the value(s) in the table below.

      B0076B8C03
      *a

      Component without harness connected

      (Headlight Housing Assembly RH)

      - -
      Standard Resistance
      Tester Connection Condition Specified Condition
      LVL-1 - F-17 Always Below 1 Ω
      LVL-2 - F-8 Always Below 1 Ω
      LVL-3 - F-20 Always Below 1 Ω
      Result
      Proceed to
      OK
      NG

    NG
    OK
  5. REPLACE HEADLIGHT LEVELING MOTOR RH


    1. Replace the headlight leveling motor RH with a new or known good one.

      Click here

    2. Perform the Active Test according to the display on the GTS.


      Body Electrical > HL AutoLeveling > Active Test
      Tester Display Measurement Item Control Range Diagnostic Note
      Drive The Leveling Motor Leveling motor upward or downward operation Stop/Down/Up Perform the Active Test with the engine started and vehicle stopped

      Body Electrical > HL AutoLeveling > Active Test
      Tester Display
      Drive The Leveling Motor
      OK
      headlight leveling motor RH operate normally.
      Result
      Proceed to
      OK
      NG

    OK
    NG