INSTRUMENT PANEL SAFETY PAD REMOVAL

PROCEDURE


  1. PRECAUTION

    Click here

    Note

    After turning the engine switch off, waiting time may be required before disconnecting the cable from the negative (-) battery terminal. Therefore, make sure to read the disconnecting the cable from the negative (-) battery terminal notices before proceeding with work.

    Click here

  2. ALIGN FRONT WHEELS FACING STRAIGHT AHEAD

  3. CHANGE POWER TILT AND POWER TELESCOPIC STEERING COLUMN SYSTEM SETTINGS (for Power Tilt and Power Telescopic Steering Column)

    Click here

  4. DISCONNECT CABLE FROM NEGATIVE BATTERY TERMINAL

    CAUTION:

    Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to disable the SRS system.

    Note

    When disconnecting the cable, some systems need to be initialized after the cable is reconnected.

    Click here

  5. REMOVE CONSOLE BOX ASSEMBLY

    Click here

  6. REMOVE FRONT DOOR SCUFF PLATE LH

    Click here

  7. REMOVE FRONT DOOR OPENING TRIM COVER LH

    Click here

  8. REMOVE INSTRUMENT SIDE PANEL LH


    1. B0072OW

      Disengage the claw and 4 clips as shown in the illustration.

    2. B0074JK

      Disengage the 2 guides to remove the instrument side panel LH as shown in the illustration.

  9. REMOVE NO. 1 INSTRUMENT PANEL UNDER COVER SUB-ASSEMBLY


    1. for LHD:


      1. B0073CO

        Remove the 2 screws <C>.

      2. Disengage the 3 clips.

      3. Disengage the connector clamp.

      4. Disconnect each connector to remove the No. 1 instrument panel under cover sub-assembly.

    2. for RHD:


      1. B0076FB

        Remove the 2 screws <C>.

      2. Disengage the 3 clips.

      3. Disengage the connector clamp.

      4. Disconnect each connector to remove the No. 1 instrument panel under cover sub-assembly.

  10. DISCONNECT HOOD LOCK CONTROL LEVER SUB-ASSEMBLY


    1. B0075X4

      Disengage the claw and 2 guides to disconnect the hood lock control lever sub-assembly.

  11. REMOVE LOWER INSTRUMENT PANEL FINISH PANEL SUB-ASSEMBLY


    1. B0074VK

      Disengage the 5 claws, 7 clips and guide.

    2. Disconnect each connector to remove the lower instrument panel finish panel sub-assembly.

  12. REMOVE SKID CONTROL BUZZER ASSEMBLY (w/ Pre-crash Safety System)

    Click here

  13. REMOVE LOWER NO. 1 INSTRUMENT PANEL AIRBAG ASSEMBLY

    Click here

  14. REMOVE METER HOOD SUB-ASSEMBLY


    1. B0077LS

      Disengage the 4 clips and 2 claws.

    2. A01VRPY

      Disengage the 2 claws as shown in the illustration.

    3. A01VS38

      Disengage the 7 clips and 3 guides as shown in the illustration.

    4. Disconnect the connector to remove the meter hood sub-assembly.

  15. REMOVE COMBINATION METER ASSEMBLY

    Click here

  16. REMOVE STEREO COMPONENT EQUALIZER ASSEMBLY (for RHD)

    Click here

  17. REMOVE TELEMATICS TRANSCEIVER WITH BRACKET (w/ Telematics Transceiver for G-BOOK)

    Click here

  18. REMOVE TELEMATICS TRANSCEIVER (w/ Telematics Transceiver except G-BOOK)

    Click here

  19. REMOVE TELEPHONE BRACKET (w/ Bracket)


    1. B0077CU

      Disengage the 2 clamps.

    2. Remove the 2 nuts and telephone bracket.

  20. REMOVE NO. 1 INSTRUMENT PANEL REGISTER ASSEMBLY


    1. B0073NG

      Disengage the 2 claws and 2 clips to remove the No. 1 instrument panel register assembly.

  21. REMOVE HORN BUTTON ASSEMBLY

    Click here

  22. REMOVE STEERING WHEEL ASSEMBLY

    Click here

  23. REMOVE FRONT DOOR SCUFF PLATE RH

    Tech Tips

    Use the same procedure as for the LH side.

  24. REMOVE FRONT DOOR OPENING TRIM COVER RH

    Tech Tips

    Use the same procedure as for the LH side.

  25. REMOVE INSTRUMENT SIDE PANEL RH


    1. B0073X5

      Disengage the claw and 4 clips as shown in the illustration.

    2. B0075S3

      Disengage the 2 guides to remove the instrument side panel RH as shown in the illustration.

    3. w/ Airbag Cut Off Switch:


      1. Disconnect the connector.

  26. REMOVE NO. 2 INSTRUMENT PANEL UNDER COVER SUB-ASSEMBLY


    1. B0076XTN01

      Disengage the 4 clips and 2 guides as indicated by the arrows, in the order shown in the illustration.

    2. Disconnect each connector to remove the No. 2 instrument panel under cover sub-assembly.

  27. REMOVE LOWER NO. 2 INSTRUMENT PANEL AIRBAG ASSEMBLY

    Click here

  28. REMOVE GLOVE COMPARTMENT DOOR ASSEMBLY


    1. B00757N

      Remove the 2 screws <C>.

    2. B0076IP

      Open the glove compartment door assembly.

    3. B0075WQ

      Remove the 3 screws <C>.

    4. B0074Y7

      Close the glove compartment door assembly.

    5. B0074FD

      Disengage the 5 claws.

    6. Disengage the connector clamp.

    7. Disconnect each connector to remove the glove compartment door assembly.

  29. REMOVE NO. 2 INSTRUMENT PANEL REGISTER ASSEMBLY


    1. B00780I

      Disengage the claw as shown in the illustration.

    2. B0075OM

      Disengage the 2 claws and 2 clips to remove the No. 2 instrument panel register assembly as shown in the illustration.

  30. REMOVE RADIO RECEIVER ASSEMBLY WITH BRACKET

    Click here

  31. REMOVE AIR CONDITIONING CONTROL ASSEMBLY

    Click here

  32. REMOVE NO. 1 SPEAKER ASSEMBLY WITH BOX (w/ ASC System)

    Click here

  33. REMOVE CENTER INSTRUMENT PANEL REGISTER ASSEMBLY


    1. B0077GE

      Disengage the 4 claws and 4 clips.

    2. Disconnect the connector to remove the center instrument panel register assembly.

  34. REMOVE INSTRUMENT CLUSTER FINISH PANEL SUB-ASSEMBLY


    1. B0075GEC01
      B0076EM Protective Tape

      Apply protective tape to the area shown in the illustration.

    2. Using a moulding remover, disengage the 3 claws as shown in the illustration.

    3. Disengage the 3 guides to remove the instrument cluster finish panel sub-assembly as shown in the illustration.

  35. REMOVE MULTI-DISPLAY ASSEMBLY WITH BRACKET

    Click here

  36. REMOVE FRONT PILLAR GARNISH LH

    Click here

  37. REMOVE NO. 1 INSTRUMENT PANEL SPEAKER PANEL SUB-ASSEMBLY


    1. B0073O0

      Disengage the 2 clips and 2 guides to remove the No. 1 instrument panel speaker panel sub-assembly as shown in the illustration.

  38. REMOVE FRONT NO. 2 SPEAKER ASSEMBLY (for LH Side)

    Click here

  39. REMOVE INSTRUMENT CLUSTER FINISH PANEL ASSEMBLY


    1. B0077K0C01
      B0076EM Protective Tape

      Apply protective tape to the area shown in the illustration.

    2. Using a moulding remover, disengage the 4 claws and 4 clips to remove the instrument cluster finish panel assembly as shown in the illustration.

  40. REMOVE FRONT NO. 3 SPEAKER ASSEMBLY

    Click here

  41. REMOVE FRONT PILLAR GARNISH RH

    Tech Tips

    Use the same procedure as for the LH side.

  42. REMOVE NO. 2 INSTRUMENT PANEL SPEAKER PANEL SUB-ASSEMBLY


    1. B00733K

      Disengage the 2 clips and 2 guides to remove the No. 2 instrument panel speaker panel sub-assembly as shown in the illustration.

  43. REMOVE FRONT NO. 2 SPEAKER ASSEMBLY (for RH Side)

    Tech Tips

    Use the same procedure as for the LH side.

  44. REMOVE INSTRUMENT CLUSTER FINISH PANEL ORNAMENT


    1. Disengage the 5 clips to remove the instrument cluster finish panel ornament as shown in the illustration.

      A01VSCG

  45. DISCONNECT NO. 2 INSTRUMENT PANEL WIRE

    Click here

  46. REMOVE INSTRUMENT PANEL SAFETY PAD SUB-ASSEMBLY


    1. Disengage the 2 claws to disconnect the room temperature sensor.

      B0077GVC01
      *1 Room Temperature Sensor - -

    2. Disconnect each connector.

    3. Disengage each clamp.

    4. Remove the 13 bolts <A>, 2 bolts <B> and nut <E>.

      B0074LOC01
      *a Bolt <A> *b Bolt <B>

    5. Disengage the 4 guides and remove the instrument panel safety pad sub-assembly as shown in the illustration.

      B0076OI

      Note


      • Do not damage the instrument panel safety pad sub-assembly.

      • Do not allow the wire harnesses to interfere with the surrounding parts.