REAR SEAT ASSEMBLY REASSEMBLY

CAUTION / NOTICE / HINT

CAUTION:

Wear protective gloves. Sharp areas on the seat frame may injure your hands.

PROCEDURE


  1. INSTALL NO. 2 CHILD RESTRAINT SEAT COVER


    1. A01FB5E

      Engage the guide to install the No. 2 child restraint seat cover.

      Tech Tips

      Use the same procedure for the other 3 No. 2 child restraint seat covers.

  2. INSTALL SEPARATE TYPE REAR SEAT CUSHION COVER RH


    1. Temporarily install the separate type rear seat cushion cover RH to the separate type rear seat cushion pad.

    2. Using hog ring pliers, install 15 new hog rings in the order indicated in the illustration.

      A01F89HC01
      *a hook - -

      Note


      • Be careful not to damage the separate type rear seat cushion cover RH.

      • Be sure to securely install the hog rings as shown in the illustration while preventing wrinkles from forming on the separate type rear seat cushion cover RH.

    3. Engage the 3 hooks.

    4. Using hog ring pliers, install the separate type rear seat cushion cover RH to the separate type rear seat cushion pad with 22 new hog rings in the order indicated in the illustration.

      A01F8AXE02

      Note


      • Be careful not to damage the separate type rear seat cushion cover RH.

      • Be sure to securely install the hog rings as shown in the illustration while preventing wrinkles from forming on the separate type rear seat cushion cover RH.

  3. INSTALL SEPARATE TYPE REAR SEAT CUSHION COVER LH

    Tech Tips

    Use the same procedure as for the RH side.

  4. INSTALL REAR SEAT UNDER TRAY SUB-ASSEMBLY


    1. Engage the 2 guides and 2 claws to install the rear seat under tray sub-assembly.

      A01FAUP

  5. INSTALL NO. 1 CHILD RESTRAINT SEAT COVER


    1. A01F8XM

      Engage the 4 claws to install the No. 1 child restraint seat cover.

      Tech Tips

      Use the same procedure for the other 3 No. 1 child restraint seat covers.

  6. INSTALL REAR SEATBACK LOCK SUB-ASSEMBLY RH (for RH Side)


    1. A01FAJPC05
      B0073AQ Screw
      B0077IM Bolt

      Engage the guide.

    2. Install the rear seatback lock sub-assembly RH to the rear seatback frame sub-assembly RH with the 2 bolts and 2 screws.

      Torque:
      Bolt
      21 N*m  { 214 kgf*cm, 15 ft.*lbf }

  7. INSTALL REAR SEAT LOCK CONTROL LEVER SUB-ASSEMBLY RH (for RH Side)


    1. A01FAXA

      Engage the 4 guides.

    2. Install the rear seat lock control lever sub-assembly RH with the screw.

    3. A01F86G

      Engage the lock clip as shown in the illustration.

  8. INSTALL REAR SEATBACK LOCK STRIKER PROTECTOR (for RH Side)


    1. A01FB49

      Engage the guide to install the rear seatback lock striker protector with the 3 screws.

  9. INSTALL SEPARATE TYPE REAR SEATBACK COVER RH (for RH Side)

    Tech Tips


    • When installing the seat cover, refer to the precautions in order to prevent wrinkles from forming.

      Click here

    • Align the seam allowance in a single direction as shown in the illustration.

      A01FAE9E01

    1. Temporarily install the separate type rear seatback cover RH to the separate type rear seatback pad.

    2. A01FAATE02

      Using hog ring pliers, install the separate type rear seatback cover RH to the separate type rear seatback pad with 7 new hog rings in the order indicated in the illustration.

      Note


      • Be careful not to damage the separate type rear seatback cover RH.


      • Be sure to securely install the hog rings as shown in the illustration while preventing wrinkles from forming on the separate type rear seatback cover RH.

  10. INSTALL SEPARATE TYPE REAR SEATBACK COVER WITH PAD (for RH Side)


    1. A01FB1RN01

      Install the separate type rear seatback cover with pad as indicated by the arrows, in the order shown in the illustration.

    2. A01F9BE

      Engage the 4 claws to install the 2 rear seat headrest supports.

  11. INSTALL REAR SEATBACK BOARD SUB-ASSEMBLY RH (for RH Side)


    1. A01F9HW

      Engage the 7 claws to install the rear seatback board sub-assembly RH.

    2. A01F8Y9

      Engage the 23 claws of the separate type rear seatback cover RH to the rear seatback board sub-assembly RH.

  12. INSTALL REAR UPPER SEATBACK LOCK BEZEL (for RH Side)


    1. A01F6UQ

      Engage the 5 claws to install the rear upper seatback lock bezel.

  13. INSTALL REAR SEATBACK LOCK COVER RH (for RH Side)


    1. A01F7P7

      Engage the 2 guides.

    2. Engage the 2 claws to install the rear seatback lock cover RH.

  14. INSTALL REAR SEATBACK LOCK CONTROL BEZEL (for RH Side)


    1. A01FA7Q

      Engage the 2 claws to install the rear seatback lock control bezel.

  15. INSTALL REAR SEAT HINGE COVER RH (for RH Side)


    1. A01F7AP

      Engage the 2 guides to install the rear seat hinge cover RH to the rear seat hinge sub-assembly RH.

    2. A01F7IV

      Tighten the bolt to install the rear seat hinge cover RH with the rear seat hinge sub-assembly RH to the separate type rear seatback cover with pad.

      Torque:
      18.1 N*m  { 185 kgf*cm, 13 ft.*lbf }

  16. INSTALL REAR SEATBACK LOCK SUB-ASSEMBLY LH (for LH Side)

    Tech Tips

    Use the same procedure as for the RH side.

  17. INSTALL REAR SEAT LOCK CONTROL LEVER SUB-ASSEMBLY LH (for LH Side)

    Tech Tips

    Use the same procedure as for the RH side.

  18. INSTALL REAR SEATBACK LOCK STRIKER PROTECTOR (for LH Side)

    Tech Tips

    Use the same procedure as for the RH side.

  19. INSTALL SEPARATE TYPE REAR SEATBACK COVER LH (for LH Side)

    Tech Tips


    • When installing the seat cover, refer to the precautions in order to prevent wrinkles from forming.

      Click here

    • Align the seam allowance in a single direction as shown in the illustration.

      A01F7T8E01

    1. Temporarily install the separate type rear seatback cover LH to the separate type rear seatback pad LH.

    2. A01FATJE02

      Using hog ring pliers, install 7 new hog rings in the order indicated in the illustration.

      Note


      • Be careful not to damage the separate type rear seatback cover LH.


      • Be sure to securely install the hog rings as shown in the illustration while preventing wrinkles from forming on the separate type rear seatback cover LH.

  20. INSTALL SEPARATE TYPE REAR SEATBACK COVER WITH PAD (for LH Side)


    1. A01F9EON01

      Install the separate type rear seatback cover with pad as indicated by the arrows, in the order shown in the illustration.

    2. A01F90N

      Engage the 4 claws to install the 2 rear seat headrest supports.

  21. INSTALL REAR SEATBACK BOARD SUB-ASSEMBLY LH (for LH Side)


    1. A01F892

      Engage the 10 claws to install the rear seatback board sub-assembly LH.

    2. A01F9GL

      Engage the 27 claws of the separate type rear seatback cover LH to the rear seatback board sub-assembly LH.

  22. INSTALL REAR UPPER SEATBACK LOCK BEZEL (for LH Side)

    Tech Tips

    Use the same procedure as for the RH side.

  23. INSTALL REAR SEATBACK LOCK COVER LH (for LH Side)

    Tech Tips

    Use the same procedure as for the RH side.

  24. INSTALL REAR SEATBACK LOCK CONTROL BEZEL (for LH Side)

    Tech Tips

    Use the same procedure as for the RH side.

  25. INSTALL REAR SEAT HINGE COVER LH (for LH Side)

    Tech Tips

    Use the same procedure as for the RH side.