ENTRY AND START SYSTEM(for Start Function) Engine does not Start

DESCRIPTION

When the electrical key transmitter sub-assembly is in the cabin and the engine switch is pressed, the certification ECU (smart key ECU assembly) receives a signal and changes the power source mode. In addition, when the shift lever is in P and the brake pedal is depressed, the engine can be started by pressing the engine switch. If the steering is unlocked, the engine can also be started by pressing the engine switch with the shift lever in N and the brake pedal depressed.

Related Data List and Active Test Items
Problem Symptom Data List and Active Test
Engine does not start

    Power Source Control

  • Stop Light Switch1

  • Steering Unlock Switch

  • Shift P Signal

  • Neutral SW/ Clutch SW

  • IG Relay Monitor (Inside)

  • IG Relay Monitor (Outside)

  • Latch Circuit

  • Starter Request Signal

  • Power Supply Condition


    Entry&Start

  • Immobiliser

  • Engine Start Request

  • S Code Check

  • L Code Check


    Starting Control

  • Starter SW

  • Shift Position P or N

  • Ignition

WIRING DIAGRAM

Click here

CAUTION / NOTICE / HINT

Note


  • When using the GTS with the engine switch off, connect the GTS to the DLC3 and turn a courtesy light switch on and off at intervals of 1.5 seconds or less until communication between the GTS and the vehicle begins. Then select Model Code "KEY REGIST" under manual mode and enter the following menus: Body Electrical / Entry&Start(CAN). While using the GTS, periodically turn a courtesy light switch on and off at intervals of 1.5 seconds or less to maintain communication between the GTS and the vehicle.

  • The entry and start system (for Start Function) uses the LIN communication system and CAN communication system. Inspect the communication function by following How to Proceed with Troubleshooting. Troubleshoot the entry and start system (for Start Function) after confirming that the communication systems are functioning properly.

    Click here

  • If the entry and start system (for Start Function) has been canceled, enable the system before performing troubleshooting.

    Click here

  • Inspect the fuses of circuits related to this system before performing the following procedure.

  • Before replacing the certification ECU (smart key ECU assembly) or electrical key transmitter sub-assembly, refer to entry and start system (for Start Function) Precaution.

    Click here

  • After completing repairs, confirm that the problem does not recur.

Tech Tips


  • When the battery cable is disconnected and reconnected, the power source returns to the mode it was in before the battery cable was disconnected.

  • If the engine switch is turned from on (IG) to on (ACC) with the shift lever in any position other than P, and then the shift lever is moved to P and the engine switch is pressed with the brake pedal depressed, the engine switch will be turned off.

  • If the brake pedal is repeatedly depressed while the engine is stopped, the brake booster pressure is released and the force required to depress the brake pedal to illuminate the stop lights increases.

PROCEDURE


  1. CHECK ELECTRICAL KEY TRANSMITTER SUB-ASSEMBLY


    1. Press a switch of the electrical key transmitter sub-assembly.

      OK
      The electrical key transmitter sub-assembly LED illuminates.
      Result
      Proceed to
      OK
      NG

    NG

    INSPECT TRANSMITTER BATTERY Click here

    OK

  2. READ VALUE USING GTS (KEY LOW BATTERY)


    1. Connect the GTS to the DLC3.

    2. Turn the engine switch on (IG).

    3. Turn the GTS on.

    4. Enter the following menus: Body Electrical / Entry&Start / Data List.

    5. Read the Data List according to the display on the GTS.


      Body Electrical > Entry&Start > Data List
      Tester Display Measurement Item Range Normal Condition Diagnostic Note
      Key Low Battery Transmitter battery depleted No or Yes

      No: Transmitter battery not depleted

      Yes: Transmitter battery depleted

      		 The electrical key transmitter sub-assembly sends voltage information to the certification ECU (smart key ECU assembly) when it is transmitting. The certification ECU (smart key ECU assembly) displays "Yes" for the "Key Low Battery" item of the Data List when this voltage information indicates 2.2 V or less. This Data List item should be checked when the electrical key transmitter sub-assembly is at room temperature (example: at -20°C (-4°F), "Yes" may be displayed even if the transmitter battery is new).

      Body Electrical > Entry&Start > Data List
      Tester Display
      Key Low Battery
      Result
      Result Proceed to
      "No" is displayed on the GTS screen A
      "Yes" is displayed on the GTS screen B

    B

    REPLACE TRANSMITTER BATTERY Click here

    A

  3. CHECK WAVE ENVIRONMENT


    1. If the problem occurs in certain locations or times of day, the possibility of wave interference is high.

      Tech Tips

      Whether the problem is due to wave interference can be checked by holding the electrical key transmitter sub-assembly near the door control receiver.

      OK
      Engine starts.
      Result
      Proceed to
      OK
      NG

    OK

    AFFECTED BY WAVE INTERFERENCE

    NG

  4. CHECK ENGINE SWITCH CONDITION


    1. Get into the vehicle while carrying an electrical key transmitter sub-assembly.

    2. Move the shift lever to P.

    3. With the brake pedal released, check that pressing the engine switch causes the power source mode to change.

      Result
      Result Proceed to
      Power source mode changes : Off → on (ACC) → on (IG) → off A
      Power source mode does not change to on (ACC) or on (IG) B
      Power source mode changes to on (IG) but not to on (ACC) C
      Power source mode changes to on (ACC) but not to on (IG) D

    B

    GO TO POWER SOURCE MODE DOES NOT CHANGE TO ON (IG AND ACC) Click here

    C

    GO TO POWER SOURCE MODE DOES NOT CHANGE TO ON (ACC) Click here

    D

    GO TO POWER SOURCE MODE DOES NOT CHANGE TO ON (IG) Click here

    A

  5. READ VALUE USING GTS (NEUTRAL SW/ CLUTCH SW, SHIFT POSITION P OR N)


    1. Connect the GTS to the DLC3.

    2. Turn the engine switch on (IG).

    3. Turn the GTS on.

    4. Enter the following menus: Body Electrical / Power Source Control or Starting Control / Data List.

    5. Read the Data List according to the display on the GTS.


      Body Electrical > Power Source Control > Data List
      Tester Display Measurement Item Range Normal Condition Diagnostic Note
      Neutral SW/ Clutch SW Shift position (P and N) OFF or ON

      OFF: Shift lever in any position other than P or N

      ON: Shift lever in P or N

      • Use this item to determine whether the park/neutral position switch assembly is malfunctioning.

      • When the engine cannot be started due to a park/neutral position switch assembly malfunction, OFF is displayed.

      Body Electrical > Power Source Control > Data List
      Tester Display
      Neutral SW/ Clutch SW

      Body Electrical > Starting Control > Data List
      Tester Display Measurement Item Range Normal Condition Diagnostic Note
      Shift Position P or N Park/Neutral position switch status OFF or ON

      OFF: Shift lever not in P

      ON: Shift lever in P

      		 When malfunctioning, the engine will not crank.

      Body Electrical > Starting Control > Data List
      Tester Display
      Shift Position P or N
      OK
      The GTS display changes correctly in response to the shift position.
      Result
      Proceed to
      OK
      NG

    NG

    INSPECT PARK/NEUTRAL POSITION SWITCH ASSEMBLY Click here

    OK

  6. CHECK FOR DTC


    1. Using the GTS, check for certification ECU (smart key ECU assembly) DTCs.


      Body Electrical > Entry&Start > Trouble Codes
      Body Electrical > Power Source Control > Trouble Codes
      Body Electrical > Starting Control > Trouble Codes
      Result
      Result Proceed to
      DTCs are not output A
      Entry and start system (for Start Function) DTCs are output B

    B

    GO TO DIAGNOSTIC TROUBLE CODE CHART Click here

    A

  7. READ VALUE USING GTS (STOP LIGHT SWITCH1)


    1. Connect the GTS to the DLC3.

    2. Turn the engine switch on (IG).

    3. Turn the GTS on.

    4. Enter the following menus: Body Electrical / Power Source Control / Data List.

    5. Read the Data List according to the display on the GTS.


      Body Electrical > Power Source Control > Data List
      Tester Display Measurement Item Range Normal Condition Diagnostic Note
      Stop Light Switch1 State of brake pedal OFF or ON

      OFF: Brake pedal released

      ON: Brake pedal depressed

      • Use this item to determine whether the stop light switch is malfunctioning.

      • The engine cannot be started when this item is OFF.

      • If the stop light switch is malfunctioning, the engine can be started by pressing and holding the engine switch for a certain period of time.

      Body Electrical > Power Source Control > Data List
      Tester Display
      Stop Light Switch1
      OK
      The GTS display changes correctly in response to the brake operation.
      Result
      Proceed to
      OK
      NG

    NG

    CHECK HARNESS AND CONNECTOR (CERTIFICATION ECU (SMART KEY ECU ASSEMBLY) - STOP LIGHT SWITCH ASSEMBLY) Click here

    OK

  8. READ VALUE USING GTS (STARTER REQUEST SIGNAL)


    1. Connect the GTS to the DLC3.

    2. Turn the engine switch on (IG).

    3. Turn the GTS on.

    4. Enter the following menus: Body Electrical / Power Source Control / Data List.

    5. Read the Data List according to the display on the GTS.


      Body Electrical > Power Source Control > Data List
      Tester Display Measurement Item Range Normal Condition Diagnostic Note
      Starter Request Signal Engine start request signal status OFF or ON

      OFF: After approx. 1 second has elapsed, the engine switch is released

      ON: With the shift lever in P and the brake pedal depressed, the engine switch is pressed and held

      • When the engine cannot be started due to a start request signal malfunction, OFF is displayed.

      • When the engine switch is pressed, the duration of time that ON is displayed will be extremely short. As such, the engine switch needs to be pressed and held for a certain period of time.

      Body Electrical > Power Source Control > Data List
      Tester Display
      Starter Request Signal

      Note

      Check that the key indicator will be displayed on the multi-information display in the combination meter assembly, and then press the engine switch.

      OK
      The GTS display changes correctly in response to the engine switch operation.
      Result
      Proceed to
      OK
      NG

    NG

    READ VALUE USING GTS (STARTER SW) Click here

    OK

  9. CHECK STEERING LOCK


    1. Check that the steering unlocks when the engine switch is turned on (ACC).

      OK
      The steering unlocks.
      Result
      Proceed to
      OK
      NG

    NG

    GO TO STEERING LOCK SYSTEM (UNABLE TO UNLOCK STEERING) Click here

    OK

  10. CHECK SECURITY INDICATOR LIGHT (IMMOBILISER SYSTEM UNSET)


    1. Get into the vehicle while carrying an electrical key transmitter sub-assembly.

    2. Move the shift lever to P.

    3. Press the engine switch with the brake pedal released and check that the security indicator light changes from blinking to off at the same time that the power source mode changes to on (ACC).

      Tech Tips

      The immobiliser function can be determined to be operating correctly if the security indicator light changes from blinking to off at the same time that the power source mode changes to on (ACC).

      OK
      The security indicator light changes from blinking to off at the same time that the power source mode changes to on (ACC).
      Result
      Proceed to
      OK
      NG

    OK

    REPLACE SMART KEY ECU ASSEMBLY

    NG

    GO TO IMMOBILISER SYSTEM (PROBLEM SYMPTOMS TABLE) Click here

  11. INSPECT TRANSMITTER BATTERY


    1. Inspect the transmitter battery.

      Click here

      Note

      Do not wrap the lead wire ground a terminal, wedge it between terminals, or solder it. The terminal may be deformed or damaged, and the transmitter battery will not be able to be installed correctly.

      Result
      Proceed to
      OK
      NG

    OK

    REPLACE ELECTRICAL KEY TRANSMITTER SUB-ASSEMBLY

    NG

    REPLACE TRANSMITTER BATTERY Click here

  12. READ VALUE USING GTS (STARTER SW)


    1. Connect the GTS to the DLC3.

    2. Turn the engine switch on (IG).

    3. Turn the GTS on.

    4. Enter the following menus: Body Electrical / Starting Control / Data List.

    5. Read the Data List according to the display on the GTS.

    6. Get into the vehicle while carrying the electrical key transmitter sub-assembly, move the shift lever to P, press the engine switch while depressing the brake pedal and confirm that the GTS display changes.


      Body Electrical > Starting Control > Data List
      Tester Display Measurement Item Range Normal Condition Diagnostic Note
      Starter SW Starter operation request OFF or ON

      OFF: Starter operation not requested

      ON: Starter operation requested

      		 When malfunctioning, the engine will not crank.

      Body Electrical > Starting Control > Data List
      Tester Display
      Starter SW
      OK
      The GTS display changes.
      Result
      Proceed to
      OK
      NG

    NG

    REPLACE SMART KEY ECU ASSEMBLY

    OK

  13. INSPECT ST RELAY (STARTER RELAY ASSEMBLY)


    1. Inspect the ST relay (starter relay assembly).

      Click here

      Result
      Proceed to
      OK
      NG

    NG

    REPLACE ST RELAY (STARTER RELAY ASSEMBLY)

    OK

  14. CHECK HARNESS AND CONNECTOR (CERTIFICATION ECU (SMART KEY ECU ASSEMBLY) - BODY GROUND)


    1. B0076ROC03
      *a

      Front view of wire harness connector

      (to Certification ECU (Smart Key ECU Assembly))

      Disconnect the A13 certification ECU (smart key ECU assembly) connector.

    2. Disconnect the A71 ECM connector.

    3. Move the shift lever to P or N.

    4. Measure the resistance according to the value(s) in the table below.

      Standard Resistance
      Tester Connection Condition Specified Condition
      A13-10 (STAR) - Body ground 20°C (68°F) 107.05 to 116.33 Ω
      A13-12 (STA) - Body ground 20°C (68°F) 106.78 to 115.98 Ω
      Result
      Proceed to
      OK
      NG

    NG

    CHECK HARNESS AND CONNECTOR (CERTIFICATION ECU (SMART KEY ECU ASSEMBLY) - PARK/NEUTRAL POSITION SWITCH) Click here

    OK

  15. INSPECT STARTER ASSEMBLY


    1. Remove the starter assembly.

      Click here

    2. Inspect the starter assembly.

      Click here

      Result
      Proceed to
      OK
      NG

    NG

    REPLACE STARTER ASSEMBLY Click here

    OK

  16. CHECK HARNESS AND CONNECTOR (BATTERY - STARTER ASSEMBLY AND ST RELAY (STARTER RELAY ASSEMBLY)


    1. Disconnect the F18 and G3 starter assembly connectors.

    2. Remove the ST relay (starter relay assembly) from the No. 1 engine room relay block and No. 1 junction block assembly.

    3. Measure the voltage according to the value(s) in the table below.

      Standard Voltage
      Tester Connection Condition Specified Condition
      G3-1(B) - Body ground Always 11 to 14 V
      5 (ST relay (starter relay assembly)) - Body ground Always 11 to 14 V

    4. Measure the resistance according to the value(s) in the table below.

      Standard Resistance
      Tester Connection Condition Specified Condition
      3 (ST relay (starter relay assembly)) - F18-1 (ST) Always Below 1 Ω
      3 (ST relay (starter relay assembly)) or F18-1 (ST) - Body ground Always 10 kΩ or higher
      Result
      Proceed to
      OK
      NG

    OK

    USE SIMULATION METHOD TO CHECK Click here

    NG

    REPAIR OR REPLACE HARNESS OR CONNECTOR

  17. CHECK HARNESS AND CONNECTOR (CERTIFICATION ECU (SMART KEY ECU ASSEMBLY) - PARK/NEUTRAL POSITION SWITCH)


    1. Disconnect the A13 certification ECU (smart key ECU assembly) connector.

    2. Disconnect the F57 park/neutral position switch assembly connector.

    3. Measure the resistance according to the value(s) in the table below.

      Standard Resistance
      Tester Connection Condition Specified Condition
      A13-10 (STAR) - F57-4 (B) Always Below 1 Ω
      A13-10 (STAR) or F57-4 (B) - Body ground Always 10 kΩ or higher
      Result
      Proceed to
      OK
      NG

    NG

    REPAIR OR REPLACE HARNESS OR CONNECTOR

    OK

  18. CHECK HARNESS AND CONNECTOR (PARK/NEUTRAL POSITION SWITCH - ST RELAY (STARTER RELAY ASSEMBLY)


    1. Disconnect the F57 park/neutral position switch assembly.

    2. Remove the ST relay (starter relay assembly) from the No. 1 engine room relay block and No. 1 junction block assembly.

    3. Measure the resistance according to the value(s) in the table below.

      Standard Resistance
      Tester Connection Condition Specified Condition
      F57-5 (L) - 2 (ST relay (starter relay assembly)) Always Below 1 Ω
      F57-5 (L) or 2 (ST relay (starter relay assembly)) - Body ground Always 10 kΩ or higher
      Result
      Proceed to
      OK
      NG

    NG

    REPAIR OR REPLACE HARNESS OR CONNECTOR

    OK

  19. CHECK HARNESS AND CONNECTOR (CERTIFICATION ECU (SMART KEY ECU ASSEMBLY) - ST RELAY (STARTER RELAY ASSEMBLY)


    1. Disconnect the A13 certification ECU (smart key ECU assembly) connector.

    2. Remove the ST relay (starter relay assembly) from the No. 1 engine room relay block and No. 1 junction block assembly.

    3. Measure the resistance according to the value(s) in the table below.

      Standard Resistance
      Tester Connection Condition Specified Condition
      A13-12 (STA) - 2 (ST relay (starter relay assembly)) Always Below 1 Ω
      A13-12 (STA) or 2 (ST relay (starter relay assembly)) - Body ground Always 10 kΩ or higher
      Result
      Proceed to
      OK
      NG

    NG

    REPAIR OR REPLACE HARNESS OR CONNECTOR

    OK

  20. CHECK HARNESS AND CONNECTOR (ST RELAY (STARTER RELAY ASSEMBLY - BODY GROUND)


    1. Remove the ST relay (starter relay assembly) from the No. 1 engine room relay block and No. 1 junction block assembly.

    2. Measure the resistance according to the value(s) in the table below.

      Standard Resistance
      Tester Connection Condition Specified Condition
      1 (ST relay (starter relay assembly)) - Body ground Always Below 1 Ω
      Result
      Proceed to
      OK
      NG

    OK

    USE SIMULATION METHOD TO CHECK Click here

    NG

    REPAIR OR REPLACE HARNESS OR CONNECTOR

  21. CHECK HARNESS AND CONNECTOR (CERTIFICATION ECU (SMART KEY ECU ASSEMBLY) - STOP LIGHT SWITCH ASSEMBLY)


    1. Disconnect the A13 certification ECU (smart key ECU assembly) connector.

    2. Disconnect the A52 stop light switch assembly connector.

    3. B00740IC99
      *a

      Front view of wire harness connector

      (to Stop Light Switch Assembly)

      Measure the voltage according to the value(s) in the table below.

      Standard Voltage
      Tester Connection Condition Specified Condition
      A52-1 (B) - Body ground Always 11 to 14 V

    4. Measure the resistance according to the value(s) in the table below.

      Standard Resistance
      Tester Connection Condition Specified Condition
      A13-2 (STP1) - A52-2 (L) Always Below 1 Ω
      A13-2 (STP1) or A52-2 (L) - Body ground Always 10 kΩ or higher
      A52-3 (GND) - Body ground Always Below 1 Ω
      Result
      Proceed to
      OK
      NG

    NG

    REPAIR OR REPLACE HARNESS OR CONNECTOR

    OK

  22. INSPECT STOP LIGHT SWITCH ASSEMBLY


    1. Inspect the stop light switch assembly.

      Click here

      Result
      Proceed to
      OK
      NG

    OK

    REPLACE SMART KEY ECU ASSEMBLY

    NG

    REPLACE STOP LAMP SWITCH ASSEMBLY Click here

  23. INSPECT PARK/NEUTRAL POSITION SWITCH ASSEMBLY


    1. Remove the park/neutral position switch assembly.

      Click here

    2. Inspect the park/neutral position switch assembly.

      Click here

      Result
      Proceed to
      OK
      NG

    NG

    REPLACE PARK/NEUTRAL POSITION SWITCH ASSEMBLY Click here

    OK

  24. CHECK HARNESS AND CONNECTOR (CERTIFICATION ECU (SMART KEY ECU ASSEMBLY) - PARK/NEUTRAL POSITION SWITCH)


    1. Disconnect the A13 certification ECU (smart key ECU assembly) connector.

    2. Disconnect the F57 park/neutral position switch assembly connector.

    3. Measure the resistance according to the value(s) in the table below.

      Standard Resistance
      Tester Connection Condition Specified Condition
      A13-10 (STAR) - F57-4 (B) Always Below 1 Ω
      A13-10 (STAR) or F57-4 (B) - Body ground Always 10 kΩ or higher
      Result
      Proceed to
      OK
      NG

    OK

    REPLACE SMART KEY ECU ASSEMBLY

    NG

    REPAIR OR REPLACE HARNESS OR CONNECTOR