REAR VIEW MONITOR SYSTEM Image from Camera for Rear View Monitor is Abnormal

DESCRIPTION

The video signals of the rear television camera assembly is transmitted to the radio receiver assembly.

WIRING DIAGRAM

A01R5L2E01

PROCEDURE


  1. CHECK HARNESS AND CONNECTOR (RADIO RECEIVER ASSEMBLY - LUGGAGE ELECTRICAL KEY SWITCH)

    Result
    Proceed to
    OK
    NG

    1. Disconnect the O71 radio receiver assembly connector.

    2. Disconnect the U40 luggage electrical key switch connector.

    3. Measure the resistance according to the value(s) in the table below.

      Standard Resistance
      Tester Connection Condition Specified Condition
      O71-11 (CA+) - U40-6 (CB+) Always Below 1 Ω
      O71-12 (V+) - U40-7 (CV+) Always Below 1 Ω
      O71-24 (V-) - U40-2 (CV-) Always Below 1 Ω
      O71-23 (CGND) - U40-1 (CGND) Always Below 1 Ω
      O71-11 (CA+) - Body ground Always 10 kΩ or higher
      O71-12 (V+) - Body ground Always 10 kΩ or higher
      O71-24 (V-) - Body ground Always 10 kΩ or higher
      O71-23 (CGND) - Body ground Always 10 kΩ or higher
      Result
      Proceed to
      OK
      NG

    NG

    REPAIR OR REPLACE HARNESS OR CONNECTOR

    OK

  2. INSPECT LUGGAGE ELECTRICAL KEY SWITCH

    Result
    Proceed to
    OK
    NG

    1. Disconnect the A rear television camera assembly connector.

    2. Inspect the luggage electrical key switch.

      Click here

      Result
      Proceed to
      OK
      NG

    NG

    REPLACE LUGGAGE ELECTRICAL KEY SWITCH Click here

    OK

  3. INSPECT RADIO RECEIVER ASSEMBLY

    Result
    Proceed to
    OK
    NG

    1. Reconnect the O71 radio receiver assembly connector.

    2. A01R3XZC04
      *a

      Component with harness connected

      (Radio Receiver Assembly)

      Measure the resistance according to the value(s) in the table below.

      Standard Resistance
      Tester Connection Condition Specified Condition
      O71-23 (CGND) - Body ground Always Below 1 Ω

    3. Measure the voltage according to the value(s) in the table below.

      Standard Voltage
      Tester Connection Condition Specified Condition
      O71-11 (CA+) - O71-23 (CGND) Engine switch on (ACC) 5.5 to 7.05 V
      Result
      Proceed to
      OK
      NG

    NG

    REPLACE RADIO RECEIVER ASSEMBLY Click here

    OK

  4. INSPECT TELEVISION CAMERA ASSEMBLY RR

    Result
    Proceed to
    OK
    NG

    1. Reconnect the U40 luggage electrical key switch connector.

    2. Reconnect the A rear television camera assembly connector.

    3. A01R5Z4C03
      *a

      Component with harness connected

      (Radio Receiver Assembly)
      B0073H3C01
      *a Waveform 1 (camera lens is not covered, displaying an image)
      *b Waveform 2 (camera lens is covered, blacking out the screen)
      *c Synchronization Signal
      *d Video Waveform

      Using an oscilloscope, check the waveform of the rear television camera assembly.

      Tech Tips

      A waterproof connector is used for the rear television camera assembly. Therefore, inspect the waveform at the radio receiver assembly with the connector connected.

      OK
      Waveform is similar to that shown in the illustration.
      Item Content
      Measurement terminal O71-12 (V+) - O68-7 (GND1)
      Measurement setting 200 mV/DIV., 50 μs./DIV.
      Condition Engine switch on (IG), shift lever in R

      Tech Tips


      • The video waveform changes according to the image sent by the rear television camera assembly.

      • The video waveform is constantly output when the engine switch is on (ACC).

      Result
      Proceed to
      OK
      NG

    OK

    PROCEED TO NEXT SUSPECTED AREA SHOWN IN PROBLEM SYMPTOMS TABLE Click here

    NG

    REPLACE TELEVISION CAMERA ASSEMBLY RR Click here