NAVIGATION SYSTEM Speaker Circuit

DESCRIPTION

If there is a short in a speaker circuit, the stereo component amplifier assembly detects it and stops output to the speakers.

Thus sound cannot be heard from the speakers even if there is no malfunction in the stereo component amplifier assembly, telematics transceiver* or speakers.

*: w/ Telematics Transceiver

WIRING DIAGRAM

Figure 1. for 10 Speakers

B0074P1E17
B0077O7E45

Figure 2. for 17 Speakers

B0074P1E18
B0072VSE04

CAUTION / NOTICE / HINT

Note


  • Depending on the parts that are replaced during vehicle inspection or maintenance, performing initialization, registration or calibration may be needed. Refer to Precaution for Navigation System.

    Click here

PROCEDURE


  1. CHECK MODEL


    1. Choose the model to be inspected.

      Result
      Result Proceed to
      for 10 Speakers A
      for 17 Speakers B

    B

    CHECK SPEAKER (OPERATION CHECK) Click here

    A

  2. CHECK SPEAKER (OPERATION CHECK)


    1. B0077Z9

      Enter the "System Check Mode" screen. Refer to Check Speaker in Operation Check.

      Click here

    2. Perform the operation check above and determine the speaker that is not operating.

      Result
      Not Operating Speaker Proceed to
      Front No. 2 speaker assembly (w/ Telematics Transceiver) A
      Front No. 2 speaker assembly (w/o Telematics Transceiver) B
      Front No. 1 speaker assembly C
      Front No. 3 speaker assembly D
      Rear speaker assembly E
      Rear No. 3 speaker assembly F

      Tech Tips

      If sound cannot be heard from any speaker, inspect all of them.


    B

    CHECK HARNESS AND CONNECTOR (STEREO COMPONENT AMPLIFIER ASSEMBLY - FRONT NO. 2 SPEAKER ASSEMBLY) Click here

    C

    CHECK HARNESS AND CONNECTOR (STEREO COMPONENT AMPLIFIER ASSEMBLY - FRONT NO. 1 SPEAKER ASSEMBLY) Click here

    D

    CHECK HARNESS AND CONNECTOR (STEREO COMPONENT AMPLIFIER ASSEMBLY - FRONT NO. 3 SPEAKER ASSEMBLY) Click here

    E

    CHECK HARNESS AND CONNECTOR (STEREO COMPONENT AMPLIFIER ASSEMBLY - REAR SPEAKER ASSEMBLY) Click here

    F

    CHECK HARNESS AND CONNECTOR (STEREO COMPONENT AMPLIFIER ASSEMBLY - REAR NO. 3 SPEAKER ASSEMBLY) Click here

    A

  3. CHECK HARNESS AND CONNECTOR (STEREO COMPONENT AMPLIFIER ASSEMBLY - TELEMATICS TRANSCEIVER - FRONT NO. 2 SPEAKER ASSEMBLY)


    1. Disconnect the T20 stereo component amplifier assembly connector.

    2. Disconnect the O150 telematics transceiver connector.

    3. Disconnect the O54 and O55 front No. 2 speaker assembly connectors.

    4. Measure the resistance according to the value (s) in the table below.

      Standard Resistance
      Tester Connection Condition Specified Condition
      T20-13 (FR+) - O150-2 (SPI+) Always Below 1 Ω
      T20-28 (FR-) - O150-3 (SPI-) Always Below 1 Ω
      O150-5 (SPO+) - O54-2 (+) Always Below 1 Ω
      O150-6 (SPO-) - O54-1 (-) Always Below 1 Ω
      T20-12 (FL+) - O55-2 (+) Always Below 1 Ω
      T20-27 (FL-) - O55-1 (-) Always Below 1 Ω
      T20-13 (FR+) or O150-2 (SPI+) - Body ground Always 10 kΩ or higher
      T20-28 (FR-) or O150-3 (SPI-) - Body ground Always 10 kΩ or higher
      T20-12 (FL+) or O55-2 (+) - Body ground Always 10 kΩ or higher
      T20-27 (FL-) or O55-1 (-) - Body ground Always 10 kΩ or higher
      O150-5 (SPO+) or O54-2 (+) - Body ground Always 10 kΩ or higher
      O150-6 (SPO-) or O54-1 (-) - Body ground Always 10 kΩ or higher
      Result
      Proceed to
      OK
      NG

    NG

    REPAIR OR REPLACE HARNESS OR CONNECTOR

    OK

  4. REPLACE FRONT NO. 2 SPEAKER ASSEMBLY


    1. Remove the front No. 2 speaker assembly.

      Click here

    2. Inspect the front No. 2 speaker assembly.

      Click here

      OK
      Malfunction disappears.
      Result
      Proceed to
      OK
      NG

    NG

    REPLACE FRONT NO. 2 SPEAKER ASSEMBLY Click here

    OK

  5. INSPECT TELEMATICS TRANSCEIVER


    1. Remove the telematics transceiver.

      Click here

    2. B00771JC05
      *a

      Component without harness connected

      (Telematics Transceiver)

      Measure the resistance according to the value(s) in the table below.

      Standard Resistance
      Tester Connection Condition Specified Condition
      2 (SPI+) - 5 (SPO+) Always Below 1 Ω
      3 (SPI-) - 6 (SPO-) Always Below 1 Ω
      2 (SPI+) - 3 (SPI-) Always 10 kΩ or higher
      5 (SPO+) - 6 (SPO-) Always 10 kΩ or higher
      2 (SPI+) - Body ground Always 10 kΩ or higher
      3 (SPI-) - Body ground Always 10 kΩ or higher
      Result
      Proceed to
      OK
      NG

    OK

    PROCEED TO NEXT SUSPECTED AREA SHOWN IN PROBLEM SYMPTOMS TABLE Click here

    NG

    REPLACE TELEMATICS TRANSCEIVER Click here

  6. CHECK HARNESS AND CONNECTOR (STEREO COMPONENT AMPLIFIER ASSEMBLY - FRONT NO. 2 SPEAKER ASSEMBLY)


    1. Disconnect the T20 stereo component amplifier assembly connector.

    2. Disconnect the O54 and O55 front No. 2 speaker assembly connectors.

    3. Measure the resistance according to the value (s) in the table below.

      Standard Resistance
      Tester Connection Condition Specified Condition
      T20-13 (FR+) - O54-2 (+) Always Below 1 Ω
      T20-28 (FR-) - O54-1 (-) Always Below 1 Ω
      T20-12 (FL+) - O55-2 (+) Always Below 1 Ω
      T20-27 (FL-) - O55-1 (-) Always Below 1 Ω
      T20-13 (FR+) or O54-2 (+) - Body ground Always 10 kΩ or higher
      T20-28 (FR-) or O54-1 (-) - Body ground Always 10 kΩ or higher
      T20-12 (FL+) or O55-2 (+) - Body ground Always 10 kΩ or higher
      T20-27 (FL-) or O55-1 (-) - Body ground Always 10 kΩ or higher
      Result
      Proceed to
      OK
      NG

    NG

    REPAIR OR REPLACE HARNESS OR CONNECTOR

    OK

  7. REPLACE FRONT NO. 2 SPEAKER ASSEMBLY


    1. Remove the front No. 2 speaker assembly.

      Click here

    2. Inspect the front No. 2 speaker assembly.

      Click here

      OK
      Malfunction disappears.
      Result
      Proceed to
      OK
      NG

    OK

    PROCEED TO NEXT SUSPECTED AREA SHOWN IN PROBLEM SYMPTOMS TABLE Click here

    NG

    REPLACE FRONT NO. 2 SPEAKER ASSEMBLY Click here

  8. CHECK HARNESS AND CONNECTOR (STEREO COMPONENT AMPLIFIER ASSEMBLY - FRONT NO. 1 SPEAKER ASSEMBLY)


    1. Disconnect the T20 stereo component amplifier assembly connector.

    2. Disconnect the R14 and S14 front No. 1 speaker assembly connectors.

    3. Measure the resistance according to the value (s) in the table below.

      Standard Resistance
      Tester Connection Condition Specified Condition
      T20-5 (WFR+) - R14-1 Always Below 1 Ω
      T20-20 (WFR-) - R14-2 Always Below 1 Ω
      T20-4 (WFL+) - S14-1 Always Below 1 Ω
      T20-19 (WFL-) - S14-2 Always Below 1 Ω
      T20-5 (WFR+) or R14-1 - Body ground Always 10 kΩ or higher
      T20-20 (WFR-) or R14-2 - Body ground Always 10 kΩ or higher
      T20-4 (WFL+) or S14-1 - Body ground Always 10 kΩ or higher
      T20-19 (WFL-) or S14-2 - Body ground Always 10 kΩ or higher
      Result
      Proceed to
      OK
      NG

    NG

    REPAIR OR REPLACE HARNESS OR CONNECTOR

    OK

  9. INSPECT FRONT NO. 1 SPEAKER ASSEMBLY


    1. Remove the front No. 1 speaker assembly.

      Click here

    2. Inspect the front No. 1 speaker assembly.

      Click here

      Result
      Proceed to
      OK
      NG

    OK

    PROCEED TO NEXT SUSPECTED AREA SHOWN IN PROBLEM SYMPTOMS TABLE Click here

    NG

    REPLACE FRONT NO. 1 SPEAKER ASSEMBLY Click here

  10. CHECK HARNESS AND CONNECTOR (STEREO COMPONENT AMPLIFIER ASSEMBLY - FRONT NO. 3 SPEAKER ASSEMBLY)


    1. Disconnect the T20 stereo component amplifier assembly connector.

    2. Disconnect the O56 front No. 3 speaker assembly connector.

    3. Measure the resistance according to the value (s) in the table below.

      Standard Resistance
      Tester Connection Condition Specified Condition
      T20-7 (CTR+) - O56-2 (+) Always Below 1 Ω
      T20-22 (CTR-) - O56-1 (-) Always Below 1 Ω
      T20-7 (CTR+) or O56-2 (+) - Body ground Always 10 kΩ or higher
      T20-22 (CTR-) or O56-1 (-) - Body ground Always 10 kΩ or higher
      Result
      Proceed to
      OK
      NG

    NG

    REPAIR OR REPLACE HARNESS OR CONNECTOR

    OK

  11. INSPECT FRONT NO. 3 SPEAKER ASSEMBLY


    1. Remove the front No. 3 speaker assembly.

      Click here

    2. Inspect the front No. 3 speaker assembly.

      Click here

      Result
      Proceed to
      OK
      NG

    OK

    PROCEED TO NEXT SUSPECTED AREA SHOWN IN PROBLEM SYMPTOMS TABLE Click here

    NG

    REPLACE FRONT NO. 3 SPEAKER ASSEMBLY Click here

  12. CHECK HARNESS AND CONNECTOR (STEREO COMPONENT AMPLIFIER ASSEMBLY - REAR SPEAKER ASSEMBLY)


    1. Disconnect the T20 stereo component amplifier assembly connector.

    2. Disconnect the T25 and U35 rear speaker assembly connectors.

    3. Measure the resistance according to the value (s) in the table below.

      Standard Resistance
      Tester Connection Condition Specified Condition
      T20-9 (RR+) - T25-1 Always Below 1 Ω
      T20-24 (RR-) - T25-2 Always Below 1 Ω
      T20-8 (RL+) - U35-1 Always Below 1 Ω
      T20-23 (RL-) - U35-2 Always Below 1 Ω
      T20-9 (RR+) or T25-1 - Body ground Always 10 kΩ or higher
      T20-24 (RR-) or T25-2 - Body ground Always 10 kΩ or higher
      T20-8 (RL+) or U35-1 - Body ground Always 10 kΩ or higher
      T20-23 (RL-) or U35-2 - Body ground Always 10 kΩ or higher
      Result
      Proceed to
      OK
      NG

    NG

    REPAIR OR REPLACE HARNESS OR CONNECTOR

    OK

  13. INSPECT REAR SPEAKER ASSEMBLY


    1. Remove the rear speaker assembly.

      Click here

    2. Inspect the rear speaker assembly.

      Click here

      Result
      Proceed to
      OK
      NG

    OK

    PROCEED TO NEXT SUSPECTED AREA SHOWN IN PROBLEM SYMPTOMS TABLE Click here

    NG

    REPLACE REAR SPEAKER ASSEMBLY Click here

  14. CHECK HARNESS AND CONNECTOR (STEREO COMPONENT AMPLIFIER ASSEMBLY - REAR NO. 3 SPEAKER ASSEMBLY)


    1. Disconnect the T20 stereo component amplifier assembly connector.

    2. Disconnect the T24 rear No. 3 speaker assembly connector.

    3. Measure the resistance according to the value (s) in the table below.

      Standard Resistance
      Tester Connection Condition Specified Condition
      T20-6 (WF1+) - T24-1 Always Below 1 Ω
      T20-21 (WF1-) - T24-2 Always Below 1 Ω
      T20-6 (WF1+) or T24-1 - Body ground Always 10 kΩ or higher
      T20-21 (WF1-) or T24-2 - Body ground Always 10 kΩ or higher
      Result
      Proceed to
      OK
      NG

    NG

    REPAIR OR REPLACE HARNESS OR CONNECTOR

    OK

  15. INSPECT REAR NO. 3 SPEAKER ASSEMBLY


    1. Remove the rear No. 3 speaker assembly.

      Click here

    2. Inspect the rear No. 3 speaker assembly.

      Click here

      Result
      Proceed to
      OK
      NG

    OK

    PROCEED TO NEXT SUSPECTED AREA SHOWN IN PROBLEM SYMPTOMS TABLE Click here

    NG

    REPLACE REAR NO. 3 SPEAKER ASSEMBLY Click here

  16. CHECK SPEAKER (OPERATION CHECK)


    1. B0077Z9

      Enter the "System Check Mode" screen. Refer to Check Speaker in Operation Check.

      Click here

    2. Perform the operation check above and determine the speaker that is not operating.

      Result
      Not Operating Speaker Proceed to
      Front No. 2 speaker assembly (w/ Telematics Transceiver) A
      Front No. 2 speaker assembly (w/o Telematics Transceiver) B
      Front No. 1 speaker assembly C
      Front No. 3 speaker assembly D
      Rear speaker assembly or rear No. 2 speaker assembly E
      Rear header speaker assembly F
      Rear No. 3 speaker assembly G

      Tech Tips

      If sound cannot be heard from any speaker, inspect all of them.


    B

    CHECK HARNESS AND CONNECTOR (STEREO COMPONENT AMPLIFIER ASSEMBLY - FRONT NO. 2 SPEAKER ASSEMBLY) Click here

    C

    CHECK HARNESS AND CONNECTOR (STEREO COMPONENT AMPLIFIER ASSEMBLY - FRONT NO. 1 SPEAKER ASSEMBLY) Click here

    D

    CHECK HARNESS AND CONNECTOR (STEREO COMPONENT AMPLIFIER ASSEMBLY - FRONT NO. 3 SPEAKER ASSEMBLY) Click here

    E

    CHECK HARNESS AND CONNECTOR (STEREO COMPONENT AMPLIFIER ASSEMBLY - REAR NO. 2 SPEAKER ASSEMBLY - REAR SPEAKER ASSEMBLY) Click here

    F

    CHECK HARNESS AND CONNECTOR (STEREO COMPONENT AMPLIFIER ASSEMBLY - REAR HEADER SPEAKER ASSEMBLY) Click here

    G

    CHECK HARNESS AND CONNECTOR (STEREO COMPONENT AMPLIFIER ASSEMBLY - REAR NO. 3 SPEAKER ASSEMBLY) Click here

    A

  17. CHECK HARNESS AND CONNECTOR (STEREO COMPONENT AMPLIFIER ASSEMBLY - TELEMATICS TRANSCEIVER - FRONT NO. 2 SPEAKER ASSEMBLY)


    1. Disconnect the T20 stereo component amplifier assembly connector.

    2. Disconnect the O150 telematics transceiver connector.

    3. Disconnect the O54 and O55 front No. 2 speaker assembly connectors.

    4. Measure the resistance according to the value (s) in the table below.

      Standard Resistance
      Tester Connection Condition Specified Condition
      T20-13 (FR+) - O150-2 (SPI+) Always Below 1 Ω
      T20-28 (FR-) - O150-3 (SPI-) Always Below 1 Ω
      O150-5 (SPO+) - O54-2 (+) Always Below 1 Ω
      O150-6 (SPO-) - O54-1 (-) Always Below 1 Ω
      T20-12 (FL+) - O55-2 (+) Always Below 1 Ω
      T20-27 (FL-) - O55-1 (-) Always Below 1 Ω
      T20-13 (FR+) or O150-2 (SPI+) - Body ground Always 10 kΩ or higher
      T20-28 (FR-) or O150-3 (SPI-) - Body ground Always 10 kΩ or higher
      T20-12 (FL+) or O55-2 (+) - Body ground Always 10 kΩ or higher
      T20-27 (FL-) or O55-1 (-) - Body ground Always 10 kΩ or higher
      O150-5 (SPO+) or O54-2 (+) - Body ground Always 10 kΩ or higher
      O150-6 (SPO-) or O54-1 (-) - Body ground Always 10 kΩ or higher
      Result
      Proceed to
      OK
      NG

    NG

    REPAIR OR REPLACE HARNESS OR CONNECTOR

    OK

  18. REPLACE FRONT NO. 2 SPEAKER ASSEMBLY


    1. Remove the front No. 2 speaker assembly.

      Click here

    2. Inspect the front No. 2 speaker assembly.

      Click here

      OK
      Malfunction disappears.
      Result
      Proceed to
      OK
      NG

    NG

    REPLACE FRONT NO. 2 SPEAKER ASSEMBLY Click here

    OK

  19. INSPECT TELEMATICS TRANSCEIVER


    1. Remove the telematics transceiver.

      Click here

    2. B00771JC05
      *a

      Component without harness connected

      (Telematics Transceiver)

      Measure the resistance according to the value(s) in the table below.

      Standard Resistance
      Tester Connection Condition Specified Condition
      2 (SPI+) - 5 (SPO+) Always Below 1 Ω
      3 (SPI-) - 6 (SPO-) Always Below 1 Ω
      2 (SPI+) - 3 (SPI-) Always 10 kΩ or higher
      5 (SPO+) - 6 (SPO-) Always 10 kΩ or higher
      2 (SPI+) - Body ground Always 10 kΩ or higher
      3 (SPI-) - Body ground Always 10 kΩ or higher
      Result
      Proceed to
      OK
      NG

    OK

    PROCEED TO NEXT SUSPECTED AREA SHOWN IN PROBLEM SYMPTOMS TABLE Click here

    NG

    REPLACE TELEMATICS TRANSCEIVER Click here

  20. CHECK HARNESS AND CONNECTOR (STEREO COMPONENT AMPLIFIER ASSEMBLY - FRONT NO. 2 SPEAKER ASSEMBLY)


    1. Disconnect the T20 stereo component amplifier assembly connector.

    2. Disconnect the O54 and O55 front No. 2 speaker assembly connectors.

    3. Measure the resistance according to the value (s) in the table below.

      Standard Resistance
      Tester Connection Condition Specified Condition
      T20-13 (FR+) - O54-2 (+) Always Below 1 Ω
      T20-28 (FR-) - O54-1 (-) Always Below 1 Ω
      T20-12 (FL+) - O55-2 (+) Always Below 1 Ω
      T20-27 (FL-) - O55-1 (-) Always Below 1 Ω
      T20-13 (FR+) or O54-2 (+) - Body ground Always 10 kΩ or higher
      T20-28 (FR-) or O54-1 (-) - Body ground Always 10 kΩ or higher
      T20-12 (FL+) or O55-2 (+) - Body ground Always 10 kΩ or higher
      T20-27 (FL-) or O55-1 (-) - Body ground Always 10 kΩ or higher
      Result
      Proceed to
      OK
      NG

    NG

    REPAIR OR REPLACE HARNESS OR CONNECTOR

    OK

  21. REPLACE FRONT NO. 2 SPEAKER ASSEMBLY


    1. Remove the front No. 2 speaker assembly.

      Click here

    2. Inspect the front No. 2 speaker assembly.

      Click here

      OK
      Malfunction disappears.
      Result
      Proceed to
      OK
      NG

    OK

    END

    NG

    PROCEED TO NEXT SUSPECTED AREA SHOWN IN PROBLEM SYMPTOMS TABLE Click here

  22. CHECK HARNESS AND CONNECTOR (STEREO COMPONENT AMPLIFIER ASSEMBLY - FRONT NO. 1 SPEAKER ASSEMBLY)


    1. Disconnect the T20 stereo component amplifier assembly connector.

    2. Disconnect the R14 and S14 front No. 1 speaker assembly connectors.

    3. Measure the resistance according to the value (s) in the table below.

      Standard Resistance
      Tester Connection Condition Specified Condition
      T20-5 (WFR+) - R14-1 Always Below 1 Ω
      T20-20 (WFR-) - R14-2 Always Below 1 Ω
      T20-4 (WFL+) - S14-1 Always Below 1 Ω
      T20-19 (WFL-) - S14-2 Always Below 1 Ω
      T20-5 (WFR+) or R14-1 - Body ground Always 10 kΩ or higher
      T20-20 (WFR-) or R14-2 - Body ground Always 10 kΩ or higher
      T20-4 (WFL+) or S14-1 - Body ground Always 10 kΩ or higher
      T20-19 (WFL-) or S14-2 - Body ground Always 10 kΩ or higher
      Result
      Proceed to
      OK
      NG

    NG

    REPAIR OR REPLACE HARNESS OR CONNECTOR

    OK

  23. INSPECT FRONT NO. 1 SPEAKER ASSEMBLY


    1. Remove the front No. 1 speaker assembly.

      Click here

    2. Inspect the front No. 1 speaker assembly.

      Click here

      Result
      Proceed to
      OK
      NG

    OK

    PROCEED TO NEXT SUSPECTED AREA SHOWN IN PROBLEM SYMPTOMS TABLE Click here

    NG

    REPLACE FRONT NO. 1 SPEAKER ASSEMBLY Click here

  24. CHECK HARNESS AND CONNECTOR (STEREO COMPONENT AMPLIFIER ASSEMBLY - FRONT NO. 3 SPEAKER ASSEMBLY)


    1. Disconnect the T20 stereo component amplifier assembly connector.

    2. Disconnect the O56 front No. 3 speaker assembly connector.

    3. Measure the resistance according to the value (s) in the table below.

      Standard Resistance
      Tester Connection Condition Specified Condition
      T20-7 (CTR+) - O56-2 (+) Always Below 1 Ω
      T20-22 (CTR-) - O56-1 (-) Always Below 1 Ω
      T20-7 (CTR+) or O56-2 (+) - Body ground Always 10 kΩ or higher
      T20-22 (CTR-) or O56-1 (-) - Body ground Always 10 kΩ or higher
      Result
      Proceed to
      OK
      NG

    NG

    REPAIR OR REPLACE HARNESS OR CONNECTOR

    OK

  25. REPLACE FRONT NO. 3 SPEAKER ASSEMBLY


    1. Remove the front No. 3 speaker assembly.

      Click here

    2. Inspect the front No. 3 speaker assembly.

      Click here

      OK
      Malfunction disappears.
      Result
      Proceed to
      OK
      NG

    OK

    END

    NG

    PROCEED TO NEXT SUSPECTED AREA SHOWN IN PROBLEM SYMPTOMS TABLE Click here

  26. CHECK HARNESS AND CONNECTOR (STEREO COMPONENT AMPLIFIER ASSEMBLY - REAR NO. 2 SPEAKER ASSEMBLY - REAR SPEAKER ASSEMBLY)


    1. Disconnect the T20 stereo component amplifier assembly connector.

    2. Disconnect the T26 and U36 rear No. 2 speaker assembly connectors.

    3. Disconnect the T25 and U35 rear speaker assembly connectors.

    4. Measure the resistance according to the value (s) in the table below.

      Standard Resistance
      Tester Connection Condition Specified Condition
      T20-9 (RR+) - T26-3 (+TW) Always Below 1 Ω
      T20-24 (RR-) - T26-1 (-TW) Always Below 1 Ω
      T20-8 (RL+) - U36-3 (+TW) Always Below 1 Ω
      T20-23 (RL-) - U36-1 (-TW) Always Below 1 Ω
      T25-1 - T26-4 (+) Always Below 1 Ω
      T25-2 - T26-2 (-) Always Below 1 Ω
      U35-1 - U36-4 (+) Always Below 1 Ω
      U35-2 - U36-2 (-) Always Below 1 Ω
      T20-9 (RR+) or T26-3 (+TW) - Body ground Always 10 kΩ or higher
      T20-24 (RR-) or T26-1 (-TW) - Body ground Always 10 kΩ or higher
      T20-8 (RL+) or U36-3 (+TW) - Body ground Always 10 kΩ or higher
      T20-23 (RL-) or U36-1 (-TW) - Body ground Always 10 kΩ or higher
      T25-1 - T26-4 (+) - Body ground Always 10 kΩ or higher
      T25-2 - T26-2 (-) - Body ground Always 10 kΩ or higher
      U35-1 - U36-4 (+) - Body ground Always 10 kΩ or higher
      U35-2 - U36-2 (-) - Body ground Always 10 kΩ or higher
      Result
      Proceed to
      OK
      NG

    NG

    REPAIR OR REPLACE HARNESS OR CONNECTOR

    OK

  27. INSPECT REAR SPEAKER ASSEMBLY


    1. Remove the rear speaker assembly.

      Click here

    2. Inspect the rear speaker assembly.

      Click here

      Result
      Proceed to
      OK
      NG

    NG

    REPLACE REAR SPEAKER ASSEMBLY Click here

    OK

  28. REPLACE REAR NO. 2 SPEAKER ASSEMBLY


    1. Remove the rear No. 2 speaker assembly.

      Click here

    2. Inspect the rear No. 2 speaker assembly.

      Click here

      OK
      Malfunction disappears.
      Result
      Proceed to
      OK
      NG

    OK

    END

    NG

    PROCEED TO NEXT SUSPECTED AREA SHOWN IN PROBLEM SYMPTOMS TABLE Click here

  29. CHECK HARNESS AND CONNECTOR (STEREO COMPONENT AMPLIFIER ASSEMBLY - REAR HEADER SPEAKER ASSEMBLY)


    1. Disconnect the T20 stereo component amplifier assembly connector.

    2. Disconnect the T23 and U34 rear header speaker assembly connectors.

    3. Measure the resistance according to the value (s) in the table below.

      Standard Resistance
      Tester Connection Condition Specified Condition
      T20-11 (SR+) - T23-2 (+) Always Below 1 Ω
      T20-26 (SR-) - T23-1 (-) Always Below 1 Ω
      T20-10 (SL+) - U34-2 (+) Always Below 1 Ω
      T20-25 (SL-) - U34-1 (-) Always Below 1 Ω
      T20-11 (SR+) or T23-2 (+) - Body ground Always 10 kΩ or higher
      T20-26 (SR-) or T23-1 (-) - Body ground Always 10 kΩ or higher
      T20-10 (SL+) or U34-2 (+) - Body ground Always 10 kΩ or higher
      T20-25 (SL-) or U34-1 (-) - Body ground Always 10 kΩ or higher
      Result
      Proceed to
      OK
      NG

    NG

    REPAIR OR REPLACE HARNESS OR CONNECTOR

    OK

  30. REPLACE REAR HEADER SPEAKER ASSEMBLY


    1. Remove the rear header speaker assembly.

      Click here

    2. Inspect the rear header speaker assembly.

      Click here

      OK
      Malfunction disappears.
      Result
      Proceed to
      OK
      NG

    OK

    END

    NG

    PROCEED TO NEXT SUSPECTED AREA SHOWN IN PROBLEM SYMPTOMS TABLE Click here

  31. CHECK HARNESS AND CONNECTOR (STEREO COMPONENT AMPLIFIER ASSEMBLY - REAR NO. 3 SPEAKER ASSEMBLY)


    1. Disconnect the T20 stereo component amplifier assembly connector.

    2. Disconnect the T24 rear No. 3 speaker assembly connector.

    3. Measure the resistance according to the value (s) in the table below.

      Standard Resistance
      Tester Connection Condition Specified Condition
      T20-6 (WF1+) - T24-1 Always Below 1 Ω
      T20-21 (WF1-) - T24-2 Always Below 1 Ω
      T20-6 (WF1+) or T24-1 - Body ground Always 10 kΩ or higher
      T20-21 (WF1-) or T24-2 - Body ground Always 10 kΩ or higher
      Result
      Proceed to
      OK
      NG

    NG

    REPAIR OR REPLACE HARNESS OR CONNECTOR

    OK

  32. INSPECT REAR NO. 3 SPEAKER ASSEMBLY


    1. Remove the rear No. 3 speaker assembly.

      Click here

    2. Inspect the rear No. 3 speaker assembly.

      Click here

      Result
      Proceed to
      OK
      NG

    OK

    PROCEED TO NEXT SUSPECTED AREA SHOWN IN PROBLEM SYMPTOMS TABLE Click here

    NG

    REPLACE REAR NO. 3 SPEAKER ASSEMBLY Click here