NAVIGATION SYSTEM Speaker Circuit

DESCRIPTION

If there is a short in a speaker circuit, the stereo component amplifier assembly detects it and stops output to the speakers.

Thus sound cannot be heard from the speakers even if there is no malfunction in the stereo component amplifier assembly or speakers.

WIRING DIAGRAM


  1. for 10 Speakers

    A01VSMEE01
    B0077O7E10

  2. for 17 Speakers

    A01VSMEE01
    B0072VSE02

PROCEDURE


  1. CHECK MODEL


    1. Choose the model to be inspected.

      Result
      Result Proceed to
      for 10 Speakers A
      for 17 Speakers B

    B

    CHECK SPEAKER (OPERATION CHECK) Click here

    A

  2. CHECK SPEAKER (OPERATION CHECK)


    1. A01VRF7

      Enter the "System Check Mode" screen. Refer to Check Speaker in Operation Check.

      Click here

    2. Perform the operation check above and determine the speaker that is not operating.

      Result
      Not Operating Speaker Proceed to
      Front No. 2 speaker assembly A
      Front No. 1 speaker assembly B
      Front No. 3 speaker assembly C
      Rear speaker assembly D
      Rear No. 3 speaker assembly E

      Tech Tips

      If sound cannot be heard from any speaker, inspect all of them.


    B

    CHECK HARNESS AND CONNECTOR (STEREO COMPONENT AMPLIFIER ASSEMBLY - FRONT NO. 1 SPEAKER ASSEMBLY) Click here

    C

    CHECK HARNESS AND CONNECTOR (STEREO COMPONENT AMPLIFIER ASSEMBLY - FRONT NO. 3 SPEAKER ASSEMBLY) Click here

    D

    CHECK HARNESS AND CONNECTOR (STEREO COMPONENT AMPLIFIER ASSEMBLY - REAR SPEAKER ASSEMBLY) Click here

    E

    CHECK HARNESS AND CONNECTOR (STEREO COMPONENT AMPLIFIER ASSEMBLY - REAR NO. 3 SPEAKER ASSEMBLY) Click here

    A

  3. CHECK HARNESS AND CONNECTOR (STEREO COMPONENT AMPLIFIER ASSEMBLY - FRONT NO. 2 SPEAKER ASSEMBLY)


    1. Disconnect the T20 stereo component amplifier assembly connector.

    2. Disconnect the O54 and O55 front No. 2 speaker assembly connectors.

    3. Measure the resistance between each of the front No. 2 speaker assemblies and the stereo component amplifier assembly to check for an open circuit in the wire harness.

      Standard Resistance
      Tester Connection Condition Specified Condition
      T20-13 (FR+) - O54-2 (+) Always Below 1 Ω
      T20-28 (FR-) - O54-1 (-) Always Below 1 Ω
      T20-12 (FL+) - O55-2 (+) Always Below 1 Ω
      T20-27 (FL-) - O55-1 (-) Always Below 1 Ω

    4. Measure the resistance between the stereo component amplifier assembly and body ground to check for a short circuit in the wire harness.

      Standard Resistance
      Tester Connection Condition Specified Condition
      T20-13 (FR+) - Body ground Always 10 kΩ or higher
      T20-28 (FR-) - Body ground Always 10 kΩ or higher
      T20-12 (FL+) - Body ground Always 10 kΩ or higher
      T20-27 (FL-) - Body ground Always 10 kΩ or higher
      Result
      Proceed to
      OK
      NG

    NG

    REPAIR OR REPLACE HARNESS OR CONNECTOR

    OK

  4. INSPECT FRONT NO. 2 SPEAKER ASSEMBLY


    1. Remove the front No. 2 speaker assembly.

      Click here

    2. B0076LHC23
      *a

      Component without harness connected

      (Front No. 2 Speaker Assembly)

      Measure the resistance according to the value(s) in the table below.

      Standard Resistance
      Tester Connection Condition Specified Condition
      1 (-) - 2 (+) Always 3.2 to 4.8 Ω
      Result
      Proceed to
      OK
      NG

    NG

    REPLACE FRONT NO. 2 SPEAKER ASSEMBLY Click here

    OK

  5. REPLACE FRONT NO. 2 SPEAKER ASSEMBLY


    1. Check that the malfunction disappears when a new or known good speaker is installed.

      Click here

      OK
      Malfunction disappears.

      Tech Tips


      • Connect all the connectors to the front No. 2 speaker assemblies that were disconnected.

      • When there is a possibility that either the right or left front No. 2 speaker assembly is defective, inspect by interchanging the right one with the left one.

      • Perform the above inspection on both the LH and RH side.

      Result
      Proceed to
      OK
      NG

    OK

    END

    NG

    PROCEED TO NEXT SUSPECTED AREA SHOWN IN PROBLEM SYMPTOMS TABLE Click here

  6. CHECK HARNESS AND CONNECTOR (STEREO COMPONENT AMPLIFIER ASSEMBLY - FRONT NO. 1 SPEAKER ASSEMBLY)


    1. Disconnect the T20 stereo component amplifier assembly connector.

    2. Disconnect the R14 and S14 front No. 1 speaker assembly connectors.

    3. Measure the resistance between each of the front No. 1 speaker assemblies and the stereo component amplifier assembly to check for an open circuit in the wire harness.

      Standard Resistance
      Tester Connection Condition Specified Condition
      T20-5 (WFR+) - R14-1 Always Below 1 Ω
      T20-20 (WFR-) - R14-2 Always Below 1 Ω
      T20-4 (WFL+) - S14-1 Always Below 1 Ω
      T20-19 (WFL-) - S14-2 Always Below 1 Ω

    4. Measure the resistance between the stereo component amplifier assembly and body ground to check for a short circuit in the wire harness.

      Standard Resistance
      Tester Connection Condition Specified Condition
      T20-5 (WFR+) - Body ground Always 10 kΩ or higher
      T20-20 (WFR-) - Body ground Always 10 kΩ or higher
      T20-4 (WFL+) - Body ground Always 10 kΩ or higher
      T20-19 (WFL-) - Body ground Always 10 kΩ or higher
      Result
      Proceed to
      OK
      NG

    NG

    REPAIR OR REPLACE HARNESS OR CONNECTOR

    OK

  7. INSPECT FRONT NO. 1 SPEAKER ASSEMBLY


    1. Remove the front No. 1 speaker assembly.

      Click here

    2. B0075DFC01
      *a

      Component without harness connected

      (Front No. 1 Speaker Assembly)

      Measure the resistance according to the value(s) in the table below.

      Standard Resistance
      Tester Connection Condition Specified Condition
      1 - 2 Always 3.2 to 4.8 Ω
      Result
      Proceed to
      OK
      NG

    OK

    PROCEED TO NEXT SUSPECTED AREA SHOWN IN PROBLEM SYMPTOMS TABLE Click here

    NG

    REPLACE FRONT NO. 1 SPEAKER ASSEMBLY Click here

  8. CHECK HARNESS AND CONNECTOR (STEREO COMPONENT AMPLIFIER ASSEMBLY - FRONT NO. 3 SPEAKER ASSEMBLY)


    1. Disconnect the T20 stereo component amplifier assembly connector.

    2. Disconnect the O56 front No. 3 speaker assembly connector.

    3. Measure the resistance between the front No. 3 speaker assembly and the stereo component amplifier assembly to check for an open circuit in the wire harness.

      Standard Resistance
      Tester Connection Condition Specified Condition
      T20-7 (CTR+) - O56-2 (+) Always Below 1 Ω
      T20-22 (CTR-) - O56-1 (-) Always Below 1 Ω

    4. Measure the resistance between the stereo component amplifier assembly and body ground to check for a short circuit in the wire harness.

      Standard Resistance
      Tester Connection Condition Specified Condition
      T20-7 (CTR+) - Body ground Always 10 kΩ or higher
      T20-22 (CTR-) - Body ground Always 10 kΩ or higher
      Result
      Proceed to
      OK
      NG

    NG

    REPAIR OR REPLACE HARNESS OR CONNECTOR

    OK

  9. INSPECT FRONT NO. 3 SPEAKER ASSEMBLY


    1. Remove the front No. 3 speaker assembly.

      Click here

    2. B0076LHC23
      *a

      Component without harness connected

      (Front No. 3 Speaker Assembly)

      Measure the resistance according to the value(s) in the table below.

      Standard Resistance
      Tester Connection Condition Specified Condition
      1 (-) - 2 (+) Always 4.0 to 6.0 Ω
      Result
      Proceed to
      OK
      NG

    OK

    PROCEED TO NEXT SUSPECTED AREA SHOWN IN PROBLEM SYMPTOMS TABLE Click here

    NG

    REPLACE FRONT NO. 3 SPEAKER ASSEMBLY Click here

  10. CHECK HARNESS AND CONNECTOR (STEREO COMPONENT AMPLIFIER ASSEMBLY - REAR SPEAKER ASSEMBLY)


    1. Disconnect the T20 stereo component amplifier assembly connector.

    2. Disconnect the T25 and U35 rear speaker assembly connectors.

    3. Measure the resistance between each of the rear speaker assemblies and the stereo component amplifier assembly to check for an open circuit in the wire harness.

      Standard Resistance
      Tester Connection Condition Specified Condition
      T20-15 (RR+) - T25-1 Always Below 1 Ω
      T20-30 (RR-) - T25-2 Always Below 1 Ω
      T20-14 (RL+) - U35-1 Always Below 1 Ω
      T20-29 (RL-) - U35-2 Always Below 1 Ω

    4. Measure the resistance between the stereo component amplifier assembly and body ground to check for a short circuit in the wire harness.

      Standard Resistance
      Tester Connection Condition Specified Condition
      T20-15 (RR+) - Body ground Always 10 kΩ or higher
      T20-30 (RR-) - Body ground Always 10 kΩ or higher
      T20-14 (RL+) - Body ground Always 10 kΩ or higher
      T20-29 (RL-) - Body ground Always 10 kΩ or higher
      Result
      Proceed to
      OK
      NG

    NG

    REPAIR OR REPLACE HARNESS OR CONNECTOR

    OK

  11. INSPECT REAR SPEAKER ASSEMBLY


    1. Remove the rear speaker assembly.

      Click here

    2. B0075DFC01
      *a

      Component without harness connected

      (Rear Speaker Assembly)

      Measure the resistance according to the value(s) in the table below.

      Standard Resistance
      Tester Connection Condition Specified Condition
      1 - 2 Always 3.2 to 4.8 Ω
      Result
      Proceed to
      OK
      NG

    OK

    PROCEED TO NEXT SUSPECTED AREA SHOWN IN PROBLEM SYMPTOMS TABLE Click here

    NG

    REPLACE REAR SPEAKER ASSEMBLY Click here

  12. CHECK HARNESS AND CONNECTOR (STEREO COMPONENT AMPLIFIER ASSEMBLY - REAR NO. 3 SPEAKER ASSEMBLY)


    1. Disconnect the T20 stereo component amplifier assembly connector.

    2. Disconnect the T24 rear No. 3 speaker assembly connector.

    3. Measure the resistance between the rear No. 3 speaker assembly and the stereo component amplifier assembly to check for an open circuit in the wire harness.

      Standard Resistance
      Tester Connection Condition Specified Condition
      T20-6 (WF1+) - T24-1 Always Below 1 Ω
      T20-21 (WF1-) - T24-2 Always Below 1 Ω

    4. Measure the resistance between the stereo component amplifier assembly and body ground to check for a short circuit in the wire harness.

      Standard Resistance
      Tester Connection Condition Specified Condition
      T20-6 (WF1+) - Body ground Always 10 kΩ or higher
      T20-21 (WF1-) - Body ground Always 10 kΩ or higher
      Result
      Proceed to
      OK
      NG

    NG

    REPAIR OR REPLACE HARNESS OR CONNECTOR

    OK

  13. INSPECT REAR NO. 3 SPEAKER ASSEMBLY


    1. Remove the rear No. 3 speaker assembly.

      Click here

    2. B0075DFC01
      *a

      Component without harness connected

      (Rear No. 3 Speaker Assembly )

      Measure the resistance according to the value(s) in the table below.

      Standard Resistance
      Tester Connection Condition Specified Condition
      1 - 2 Always 2.0 to 3.0 Ω
      Result
      Proceed to
      OK
      NG

    OK

    PROCEED TO NEXT SUSPECTED AREA SHOWN IN PROBLEM SYMPTOMS TABLE Click here

    NG

    REPLACE REAR NO. 3 SPEAKER ASSEMBLY Click here

  14. CHECK SPEAKER (OPERATION CHECK)


    1. A01VRF7

      Enter the "System Check Mode" screen. Refer to Check Speaker in Operation Check.

      Click here

    2. Perform the operation check above and determine the speaker that is not operating.

      Result
      Not Operating Speaker Proceed to
      Front No. 2 speaker assembly A
      Front No. 1 speaker assembly B
      Front No. 3 speaker assembly C
      Rear speaker assembly or rear No. 2 speaker assembly D
      Rear header speaker assembly E
      Rear No. 3 speaker assembly F

      Tech Tips

      If sound cannot be heard from any speaker, inspect all of them.


    B

    CHECK HARNESS AND CONNECTOR (STEREO COMPONENT AMPLIFIER ASSEMBLY - FRONT NO. 1 SPEAKER ASSEMBLY) Click here

    C

    CHECK HARNESS AND CONNECTOR (STEREO COMPONENT AMPLIFIER ASSEMBLY - FRONT NO. 3 SPEAKER ASSEMBLY) Click here

    D

    CHECK HARNESS AND CONNECTOR (STEREO COMPONENT AMPLIFIER ASSEMBLY - REAR NO. 2 SPEAKER ASSEMBLY - REAR SPEAKER ASSEMBLY) Click here

    E

    CHECK HARNESS AND CONNECTOR (STEREO COMPONENT AMPLIFIER ASSEMBLY - REAR HEADER SPEAKER ASSEMBLY) Click here

    F

    CHECK HARNESS AND CONNECTOR (STEREO COMPONENT AMPLIFIER ASSEMBLY - REAR NO. 3 SPEAKER ASSEMBLY) Click here

    A

  15. CHECK HARNESS AND CONNECTOR (STEREO COMPONENT AMPLIFIER ASSEMBLY - FRONT NO. 2 SPEAKER ASSEMBLY)


    1. Disconnect the T20 stereo component amplifier assembly connector.

    2. Disconnect the O54 and O55 front No. 2 speaker assembly connectors.

    3. Measure the resistance between the stereo component amplifier assembly and each of the front No. 2 speaker assemblies to check for an open circuit in the wire harness.

      Standard Resistance
      Tester Connection Condition Specified Condition
      T20-13 (FR+) - O54-2 (+) Always Below 1 Ω
      T20-28 (FR-) - O54-1 (-) Always Below 1 Ω
      T20-12 (FL+) - O55-2 (+) Always Below 1 Ω
      T20-27 (FL-) - O55-1 (-) Always Below 1 Ω

    4. Measure the resistance between the stereo component amplifier assembly and body ground to check for a short circuit in the wire harness.

      Standard Resistance
      Tester Connection Condition Specified Condition
      T20-13 (FR+) - Body ground Always 10 kΩ or higher
      T20-28 (FR-) - Body ground Always 10 kΩ or higher
      T20-12 (FL+) - Body ground Always 10 kΩ or higher
      T20-27 (FL-) - Body ground Always 10 kΩ or higher
      Result
      Proceed to
      OK
      NG

    NG

    REPAIR OR REPLACE HARNESS OR CONNECTOR

    OK

  16. INSPECT FRONT NO. 2 SPEAKER ASSEMBLY


    1. Remove the front No. 2 speaker assembly.

      Click here

    2. B0076LHC23
      *a

      Component without harness connected

      (Front No. 2 Speaker Assembly)

      Measure the resistance according to the value(s) in the table below.

      Standard Resistance
      Tester Connection Condition Specified Condition
      1 (-) - 2 (+) Always 6.5 to 9.7 Ω
      Result
      Proceed to
      OK
      NG

    NG

    REPLACE FRONT NO. 2 SPEAKER ASSEMBLY Click here

    OK

  17. REPLACE FRONT NO. 2 SPEAKER ASSEMBLY


    1. Check that the malfunction disappears when a new or known good speaker is installed.

      Click here

      OK
      Malfunction disappears.

      Tech Tips


      • Connect all the connectors to the front No. 2 speaker assemblies that were disconnected.

      • When there is a possibility that either the right or left front No. 2 speaker assembly is defective, inspect by interchanging the right one with the left one.

      • Perform the above inspection on both the LH and RH side.

      Result
      Proceed to
      OK
      NG

    OK

    END

    NG

    PROCEED TO NEXT SUSPECTED AREA SHOWN IN PROBLEM SYMPTOMS TABLE Click here

  18. CHECK HARNESS AND CONNECTOR (STEREO COMPONENT AMPLIFIER ASSEMBLY - FRONT NO. 1 SPEAKER ASSEMBLY)


    1. Disconnect the T20 stereo component amplifier assembly connector.

    2. Disconnect the R14 and S14 front No. 1 speaker assembly connectors.

    3. Measure the resistance between each of the front No. 1 speaker assemblies and the stereo component amplifier assembly to check for an open circuit in the wire harness.

      Standard Resistance
      Tester Connection Condition Specified Condition
      T20-5 (WFR+) - R14-1 Always Below 1 Ω
      T20-20 (WFR-) - R14-2 Always Below 1 Ω
      T20-4 (WFL+) - S14-1 Always Below 1 Ω
      T20-19 (WFL-) - S14-2 Always Below 1 Ω

    4. Measure the resistance between the stereo component amplifier assembly and body ground to check for a short circuit in the wire harness.

      Standard Resistance
      Tester Connection Condition Specified Condition
      T20-5 (WFR+) - Body ground Always 10 kΩ or higher
      T20-20 (WFR-) - Body ground Always 10 kΩ or higher
      T20-4 (WFL+) - Body ground Always 10 kΩ or higher
      T20-19 (WFL-) - Body ground Always 10 kΩ or higher
      Result
      Proceed to
      OK
      NG

    NG

    REPAIR OR REPLACE HARNESS OR CONNECTOR

    OK

  19. INSPECT FRONT NO. 1 SPEAKER ASSEMBLY


    1. Remove the front No. 1 speaker assembly.

      Click here

    2. B0075DFC01
      *a

      Component without harness connected

      (Front No. 1 Speaker Assembly)

      Measure the resistance according to the value(s) in the table below.

      Standard Resistance
      Tester Connection Condition Specified Condition
      1 - 2 Always 4.3 to 6.3 Ω
      Result
      Proceed to
      OK
      NG

    OK

    PROCEED TO NEXT SUSPECTED AREA SHOWN IN PROBLEM SYMPTOMS TABLE Click here

    NG

    REPLACE FRONT NO. 1 SPEAKER ASSEMBLY Click here

  20. CHECK HARNESS AND CONNECTOR (STEREO COMPONENT AMPLIFIER ASSEMBLY - FRONT NO. 3 SPEAKER ASSEMBLY)


    1. Disconnect the T20 stereo component amplifier assembly connector.

    2. Disconnect the O56 front No. 3 speaker assembly connector.

    3. Measure the resistance between the front No. 3 speaker assembly and the stereo component amplifier assembly to check for an open circuit in the wire harness.

      Standard Resistance
      Tester Connection Condition Specified Condition
      T20-7 (CTR+) - O56-2 (+) Always Below 1 Ω
      T20-22 (CTR-) - O56-1 (-) Always Below 1 Ω

    4. Measure the resistance between the stereo component amplifier assembly and body ground to check for a short circuit in the wire harness.

      Standard Resistance
      Tester Connection Condition Specified Condition
      T20-7 (CTR+) - Body ground Always 10 kΩ or higher
      T20-22 (CTR-) - Body ground Always 10 kΩ or higher
      Result
      Proceed to
      OK
      NG

    NG

    REPAIR OR REPLACE HARNESS OR CONNECTOR

    OK

  21. INSPECT FRONT NO. 3 SPEAKER ASSEMBLY


    1. Remove the front No. 3 speaker assembly.

      Click here

    2. B0076LHC23
      *a

      Component without harness connected

      (Front No. 3 Speaker Assembly)

      Measure the resistance according to the value(s) in the table below.

      Standard Resistance
      Tester Connection Condition Specified Condition
      1 (-) - 2 (+) Always 6.5 to 9.7 Ω
      Result
      Proceed to
      OK
      NG

    NG

    REPLACE FRONT NO. 3 SPEAKER ASSEMBLY Click here

    OK

  22. REPLACE FRONT NO. 3 SPEAKER ASSEMBLY


    1. Check that the malfunction disappears when a new or known good speaker is installed.

      Click here

      OK
      Malfunction disappears.
      Result
      Proceed to
      OK
      NG

    OK

    END

    NG

    PROCEED TO NEXT SUSPECTED AREA SHOWN IN PROBLEM SYMPTOMS TABLE Click here

  23. CHECK HARNESS AND CONNECTOR (STEREO COMPONENT AMPLIFIER ASSEMBLY - REAR NO. 2 SPEAKER ASSEMBLY - REAR SPEAKER ASSEMBLY)


    1. Disconnect the T20 stereo component amplifier assembly connector.

    2. Disconnect the T26 and U36 rear No. 2 speaker assembly connectors.

    3. Disconnect the T25 and U35 rear speaker assembly connectors.

    4. Measure the resistance between each of the rear No. 2 speaker assemblies and the stereo component amplifier assembly to check for an open circuit in the wire harness.

      Standard Resistance
      Tester Connection Condition Specified Condition
      T20-15 (RR+) - T26-3 (+TW) Always Below 1 Ω
      T20-30 (RR-) - T26-1 (-TW) Always Below 1 Ω
      T20-14 (RL+) - U36-3 (+TW) Always Below 1 Ω
      T20-29 (RL-) - U36-1 (-TW) Always Below 1 Ω

    5. Measure the resistance between each of the rear speaker assemblies and the rear No. 2 speaker assemblies to check for an open circuit in the wire harness.

      Standard Resistance
      Tester Connection Condition Specified Condition
      T25-1 - T26-4 (+) Always Below 1 Ω
      T25-2 - T26-2 (-) Always Below 1 Ω
      U35-1 - U36-4 (+) Always Below 1 Ω
      U35-2 - U36-2 (-) Always Below 1 Ω

    6. Measure the resistance between the stereo component amplifier assembly and body ground to check for a short circuit in the wire harness.

      Standard Resistance
      Tester Connection Condition Specified Condition
      T20-15 (RR+) - Body ground Always 10 kΩ or higher
      T20-30 (RR-) - Body ground Always 10 kΩ or higher
      T20-14 (RL+) - Body ground Always 10 kΩ or higher
      T20-29 (RL-) - Body ground Always 10 kΩ or higher

    7. Measure the resistance between each of the rear No. 2 speaker assemblies and body ground to check for a short circuit in the wire harness.

      Standard Resistance
      Tester Connection Condition Specified Condition
      T26-4 (+) - Body ground Always 10 kΩ or higher
      T26-2 (-) - Body ground Always 10 kΩ or higher
      U36-4 (+) - Body ground Always 10 kΩ or higher
      U36-2 (-) - Body ground Always 10 kΩ or higher
      Result
      Proceed to
      OK
      NG

    NG

    REPAIR OR REPLACE HARNESS OR CONNECTOR

    OK

  24. INSPECT REAR SPEAKER ASSEMBLY


    1. Remove the rear speaker assembly.

      Click here

    2. B0075DFC01
      *a

      Component without harness connected

      (Rear Speaker Assembly)

      Measure the resistance according to the value(s) in the table below.

      Standard Resistance
      Tester Connection Condition Specified Condition
      1 - 2 Always 3.6 to 5.6 Ω
      Result
      Proceed to
      OK
      NG

    NG

    REPLACE REAR SPEAKER ASSEMBLY Click here

    OK

  25. INSPECT REAR NO. 2 SPEAKER ASSEMBLY


    1. Remove the rear No. 2 speaker assembly.

      Click here

    2. B00774LC21
      *a

      Component without harness connected

      (Rear No. 2 Speaker Assembly)

      Measure the resistance according to the value(s) in the table below.

      Standard Resistance
      Tester Connection Condition Specified Condition
      3 (+TW) - 1 (-TW) Always 10 kΩ or higher
      3 (+TW) - 4 (+) Always Below 1 Ω
      1 (-TW) - 2 (-) Always Below 1 Ω
      Result
      Proceed to
      OK
      NG

    NG

    REPLACE REAR NO. 2 SPEAKER ASSEMBLY Click here

    OK

  26. REPLACE REAR NO. 2 SPEAKER ASSEMBLY


    1. Check that the malfunction disappears when a new or known good speaker is installed.

      Click here

      OK
      Malfunction disappears.

      Tech Tips


      • Connect all the connectors to the rear No. 2 speaker assemblies that were disconnected.

      • When there is a possibility that either the right or left rear No. 2 speaker assembly is defective, inspect by interchanging the right one with the left one.

      • Perform the above inspection on both the LH and RH side.

      Result
      Proceed to
      OK
      NG

    OK

    END

    NG

    PROCEED TO NEXT SUSPECTED AREA SHOWN IN PROBLEM SYMPTOMS TABLE Click here

  27. CHECK HARNESS AND CONNECTOR (STEREO COMPONENT AMPLIFIER ASSEMBLY - REAR HEADER SPEAKER ASSEMBLY)


    1. Disconnect the T20 stereo component amplifier assembly connector.

    2. Disconnect the T23 and U34 rear header speaker assembly connectors.

    3. Measure the resistance between each of the rear header speaker assemblies and the stereo component amplifier assembly to check for an open circuit in the wire harness.

      Standard Resistance
      Tester Connection Condition Specified Condition
      T20-11 (SR+) - T23-2 Always Below 1 Ω
      T20-26 (SR-) - T23-1 Always Below 1 Ω
      T20-10 (SL+) - U34-2 Always Below 1 Ω
      T20-25 (SL-) - U34-1 Always Below 1 Ω

    4. Measure the resistance between the stereo component amplifier assembly and body ground to check for a short circuit in the wire harness.

      Standard Resistance
      Tester Connection Condition Specified Condition
      T20-11 (SR+) - Body ground Always 10 kΩ or higher
      T20-26 (SR-) - Body ground Always 10 kΩ or higher
      T20-10 (SL+) - Body ground Always 10 kΩ or higher
      T20-25 (SL-) - Body ground Always 10 kΩ or higher
      Result
      Proceed to
      OK
      NG

    NG

    REPAIR OR REPLACE HARNESS OR CONNECTOR

    OK

  28. INSPECT REAR HEADER SPEAKER ASSEMBLY


    1. Remove the rear header speaker assembly.

      Click here

    2. B0075BAC01
      *a

      Component without harness connected

      (Rear Header Speaker Assembly)

      Measure the resistance according to the value(s) in the table below.

      Standard Resistance
      Tester Connection Condition Specified Condition
      1 - 2 Always 6.5 to 9.7 Ω
      Result
      Proceed to
      OK
      NG

    NG

    REPLACE REAR HEADER SPEAKER ASSEMBLY Click here

    OK

  29. REPLACE REAR HEADER SPEAKER ASSEMBLY


    1. Check that the malfunction disappears when a new or known good speaker is installed.

      Click here

      OK
      Malfunction disappears.

      Tech Tips


      • Connect all the connectors to the rear header speaker assemblies that were disconnected.

      • When there is a possibility that either the right or left rear header speaker assembly is defective, inspect by interchanging the right one with the left one.

      • Perform the above inspection on both the LH and RH side.

      Result
      Proceed to
      OK
      NG

    OK

    END

    NG

    PROCEED TO NEXT SUSPECTED AREA SHOWN IN PROBLEM SYMPTOMS TABLE Click here

  30. CHECK HARNESS AND CONNECTOR (STEREO COMPONENT AMPLIFIER ASSEMBLY - REAR NO. 3 SPEAKER ASSEMBLY)


    1. Disconnect the T20 stereo component amplifier assembly connector.

    2. Disconnect the T24 rear No. 3 speaker assembly connector.

    3. Measure the resistance between the rear No. 3 speaker assembly and the stereo component amplifier assembly to check for an open circuit in the wire harness.

      Standard Resistance
      Tester Connection Condition Specified Condition
      T20-6 (WF1+) - T24-1 Always Below 1 Ω
      T20-21 (WF1-) - T24-2 Always Below 1 Ω

    4. Measure the resistance between the stereo component amplifier assembly and body ground to check for a short circuit in the wire harness.

      Standard Resistance
      Tester Connection Condition Specified Condition
      T20-6 (WF1+) - Body ground Always 10 kΩ or higher
      T20-21 (WF1-) - Body ground Always 10 kΩ or higher
      Result
      Proceed to
      OK
      NG

    NG

    REPAIR OR REPLACE HARNESS OR CONNECTOR

    OK

  31. INSPECT REAR NO. 3 SPEAKER ASSEMBLY


    1. Remove the rear No. 3 speaker assembly.

      Click here

    2. B0075DFC01
      *a

      Component without harness connected

      (Rear No. 3 Speaker Assembly)

      Measure the resistance according to the value(s) in the table below.

      Standard Resistance
      Tester Connection Condition Specified Condition
      1 - 2 Always 4.8 to 6.8 Ω
      Result
      Proceed to
      OK
      NG

    OK

    PROCEED TO NEXT SUSPECTED AREA SHOWN IN PROBLEM SYMPTOMS TABLE Click here

    NG

    REPLACE REAR NO. 3 SPEAKER ASSEMBLY Click here