PARKING BRAKE PEDAL(for RHD) INSTALLATION

PROCEDURE


  1. INSTALL PARKING BRAKE CONTROL PEDAL ASSEMBLY


    1. B0077VSN01

      Install the parking brake control pedal assembly to the body with the bolt and 2 nuts.

      Torque:
      12.7 N*m  { 130 kgf*cm, 9 ft.*lbf }

      Note

      Tighten the bolt and 2 nuts in the order shown in the illustration.

    2. Connect the parking brake switch connector.

    3. Install the No. 1 parking brake cable assembly with the 2 bolts.

      Torque:
      8.0 N*m  { 82 kgf*cm, 71 in.*lbf }

    4. Install the No. 1 parking brake cable assembly to the body with the 2 nuts.

      Torque:
      6.0 N*m  { 61 kgf*cm, 53 in.*lbf }

  2. INSTALL PARKING BRAKE EQUALIZER


    1. B0077FZN01

      Install the parking brake equalizer as shown in the illustration.

    2. B0076WDC01
      *a Groove

      Slide the rubber boot back as shown in the illustration.

      Note

      Securely fit the protrusion on the rubber boot into the No. 1 parking brake cable assembly groove.

    3. Connect the No. 2 parking brake cable assembly and No. 3 parking brake cable assembly to the parking brake equalizer.

    4. Install the No. 2 parking brake cable assembly and No. 3 parking brake cable assembly with the 2 nuts.

      Torque:
      6.0 N*m  { 61 kgf*cm, 53 in.*lbf }

  3. INSTALL PARKING BRAKE RETURN WITH DAMPER SPRING


    1. Using needle-nose pliers, install the parking brake return with damper spring.

  4. INSPECT PARKING BRAKE PEDAL TRAVEL

    Click here

  5. ADJUST PARKING BRAKE PEDAL TRAVEL

    Click here

  6. INSTALL FRONT FLOOR REAR UPPER SUB PANEL SUB-ASSEMBLY


    1. B0073J7

      Engage the clamp and install the front floor rear upper sub panel sub-assembly.

    2. B0074CW

      Install the 4 bolts.

      Torque:
      17.5 N*m  { 178 kgf*cm, 13 ft.*lbf }

    3. Engage the 2 guides to the front floor carpet assembly.

    4. B0077QS

      Engage the 6 clamps.

  7. INSTALL AIRBAG ECU ASSEMBLY

    Tech Tips

    Use the same procedure as for LHD.

    Click here

  8. INSTALL NO. 2 DASH PANEL INSULATOR PAD


    1. Engage the 2 clips to install the No. 2 dash panel insulator pad.

  9. INSTALL REAR NO. 3 AIR DUCT

    Tech Tips

    Use the same procedure as for LHD.

    Click here

  10. INSTALL FRONT FLOOR SILENCER PAD RH

    Tech Tips

    Use the same procedure as for LHD.

    Click here

  11. INSTALL REAR NO. 4 AIR DUCT

    Tech Tips

    Use the same procedure as for LHD.

    Click here

  12. INSTALL ACCELERATOR PEDAL ASSEMBLY

    Tech Tips

    Use the same procedure as for LHD.

    Click here

  13. INSTALL ACCELERATOR PEDAL PAD

    Tech Tips

    Use the same procedure as for LHD.

    Click here

  14. INSTALL NO. 2 AIR DUCT SUB-ASSEMBLY

    Tech Tips

    Use the same procedure as for LHD.

    Click here

  15. INSTALL LOWER NO. 1 INSTRUMENT PANEL AIRBAG ASSEMBLY

    Tech Tips

    Use the same procedure as for LHD.

    Click here

  16. INSTALL YAWRATE SENSOR BRACKET

    Tech Tips

    Use the same procedure as for LHD.

    Click here

  17. INSTALL FRONT SEAT ASSEMBLY LH

    Tech Tips

    Use the same procedure as for LHD.

    Click here

  18. INSTALL PROPELLER SHAFT WITH CENTER BEARING ASSEMBLY

    Click here

  19. INSPECT BRAKE WARNING LIGHT

    Click here