REAR AXLE HUB INSTALLATION

CAUTION / NOTICE / HINT

Tech Tips


  • Use the same procedure for the RH side and LH side.

  • The following procedure is for the LH side.

PROCEDURE


  1. INSTALL REAR AXLE HUB AND BEARING ASSEMBLY


    1. Hold the rear axle carrier sub-assembly between aluminum plates in a vise.

      Note

      Do not overtighten the vise.

    2. Install the rear axle hub and bearing assembly and parking brake plate sub-assembly to the rear axle carrier sub-assembly with the 4 bolts.

      Torque:
      75 N*m  { 765 kgf*cm, 55 ft.*lbf }

  2. INSTALL REAR NO. 1 WHEEL BEARING DUST DEFLECTOR


    1. B0075O6C01
      *a Hole

      Set a new rear No. 1 wheel bearing dust deflector to the rear axle carrier sub-assembly while aligning the hole for the rear speed sensor in the rear No. 1 wheel bearing dust deflector with the hole of the rear axle carrier sub-assembly.

    2. B0076GHC02
      *1 Rear No. 1 Wheel Bearing Dust Deflector
      *a Hole

      Using SST and a press, install the rear No. 1 wheel bearing dust deflector.

      SST
      09950-70010   ( 09951-07150 )
      09951-01000

  3. INSTALL REAR AXLE ASSEMBLY


    1. B00746MC01
      *a Matchmark

      Install the rear axle assembly to the rear drive shaft assembly.

      Note

      Align the matchmarks on the rear drive shaft assembly and rear axle hub and bearing assembly.

  4. TEMPORARILY INSTALL REAR UPPER CONTROL ARM ASSEMBLY

    Click here

  5. TEMPORARILY INSTALL REAR NO. 1 UPPER CONTROL ARM ASSEMBLY

    Click here

  6. INSTALL REAR LOWER COIL SPRING INSULATOR

    Click here

  7. INSTALL REAR UPPER COIL SPRING INSULATOR

    Click here

  8. INSTALL REAR COIL SPRING

    Click here

  9. TEMPORARILY INSTALL REAR SHOCK ABSORBER ASSEMBLY

    Click here

  10. INSTALL REAR STABILIZER LINK ASSEMBLY

    Click here

  11. TEMPORARILY INSTALL REAR NO. 1 SUSPENSION ARM ASSEMBLY


    1. Temporarily install the rear No. 1 suspension arm assembly to the rear axle carrier sub-assembly with the bolt and nut.

      Note

      Because the nut has its own stopper, do not turn the nut. Tighten the bolt with the nut secured.

      Tech Tips

      Insert the bolt with the threaded end facing the front of the vehicle.

  12. TEMPORARILY INSTALL TOE CONTROL LINK SUB-ASSEMBLY (w/o Dynamic Rear Steering)

    Click here

  13. INSTALL REAR STEERING TIE ROD ASSEMBLY (w/ Dynamic Rear Steering)

    Click here

  14. INSTALL PARKING BRAKE ASSEMBLY

    Click here

  15. INSTALL REAR DISC

    Click here

  16. INSTALL REAR DISC BRAKE CALIPER ASSEMBLY

    Click here

  17. TEMPORARILY INSTALL REAR AXLE SHAFT NUT


    1. Clean the threaded parts on the rear drive shaft assembly and a new rear axle shaft nut using non-residue solvent.

      Note


      • Be sure to perform this work even when using a new rear drive shaft assembly.

      • Keep the threaded parts free of oil and foreign matter.

    2. Using a 32 mm socket wrench, while applying the brakes, temporarily install the rear axle shaft nut.

      Torque:
      290 N*m  { 2957 kgf*cm, 214 ft.*lbf }

      Note

      Stake the rear axle shaft nut after inspecting for looseness and runout in the following steps.

      Tech Tips

      Keep depressing the brake pedal to prevent the rear drive shaft assembly from rotating.

  18. SEPARATE REAR DISC BRAKE CALIPER ASSEMBLY

    Click here

  19. REMOVE REAR DISC

    Click here

  20. INSPECT REAR AXLE HUB BEARING LOOSENESS

    Click here

  21. INSPECT REAR AXLE HUB RUNOUT

    Click here

  22. INSTALL REAR DISC

    Click here

  23. INSTALL PARKING BRAKE SHOE ADJUSTING HOLE PLUG

    Click here

  24. INSTALL REAR DISC BRAKE CALIPER ASSEMBLY

    Click here

  25. INSTALL REAR AXLE SHAFT NUT


    1. B0074EC

      Using a chisel and hammer, stake the rear axle shaft nut.

  26. INSTALL REAR SPEED SENSOR


    1. Install the rear speed sensor to the rear axle carrier sub-assembly with the 2 bolts.

      Torque:
      8.5 N*m  { 87 kgf*cm, 75 in.*lbf }

  27. STABILIZE SUSPENSION

    Click here

  28. FULLY TIGHTEN TOE CONTROL LINK SUB-ASSEMBLY (w/o Dynamic Rear Steering)

    Click here

  29. FULLY TIGHTEN REAR UPPER CONTROL ARM ASSEMBLY


    1. Fully tighten the rear upper control arm assembly nut.

      Torque:
      190 N*m  { 1937 kgf*cm, 140 ft.*lbf }

      Note

      Because the bolt has its own stopper, do not turn the bolt. Tighten the nut with the bolt secured.

    2. Install the rear speed sensor to the rear upper control arm assembly with the bolt.

      Torque:
      8.5 N*m  { 87 kgf*cm, 75 in.*lbf }

  30. FULLY TIGHTEN REAR NO. 1 UPPER CONTROL ARM ASSEMBLY


    1. Fully tighten the rear No. 1 upper control arm assembly nut.

      Torque:
      150 N*m  { 1530 kgf*cm, 111 ft.*lbf }

      Note

      Because the bolt has its own stopper, do not turn the bolt. Tighten the nut with the bolt secured.

  31. FULLY TIGHTEN REAR SHOCK ABSORBER ASSEMBLY

    Click here

  32. FULLY TIGHTEN REAR NO. 2 SUSPENSION ARM ASSEMBLY

    Click here

  33. FULLY TIGHTEN REAR NO. 1 SUSPENSION ARM ASSEMBLY

    Click here

  34. INSTALL REAR SUSPENSION ARM COVER

    Click here

  35. INSTALL REAR HEIGHT CONTROL SENSOR SUB-ASSEMBLY

    Click here

  36. ADJUST PARKING BRAKE

    Click here

  37. INSTALL REAR WHEEL

    Click here

  38. INSPECT AND ADJUST REAR WHEEL ALIGNMENT

    Click here

  39. CHECK FOR SPEED SENSOR SIGNAL

    Click here

  40. INITIALIZE HEIGHT CONTROL SENSOR SIGNAL (for Single Beam Headlight)

    Click here

  41. INITIALIZE HEIGHT CONTROL SENSOR SIGNAL (for Triple Beam Headlight)

    Click here

  42. ADJUST HEADLIGHT AIMING (for Single Beam Headlight)

    Click here

  43. ADJUST HEADLIGHT AIMING (for Triple Beam Headlight)

    Click here