AUTOMATIC TRANSMISSION ASSEMBLY(for 2GR) INSTALLATION

CAUTION / NOTICE / HINT

CAUTION:

The automatic transmission assembly is very heavy. Be sure to follow the procedure described in the repair manual, or the transmission jack may suddenly drop.

PROCEDURE


  1. INSTALL TORQUE CONVERTER ASSEMBLY


    1. B00743SC03
      *a Engine Assembly Surface
      *b Drive Plate Surface

      Using a vernier caliper and straightedge, measure the dimension (A) between the automatic transmission assembly contact surface of the engine assembly and the torque converter assembly contact surface of the drive plate.

    2. B0076G6C01
      *a Matchmark

      Align the matchmark on the automatic transmission case sub-assembly with the one on the torque converter assembly and engage the splines of the input shaft with the turbine runner splines.

      Note

      Install the torque converter assembly to the input shaft while keeping it horizontal.

    3. B0076BRC01
      *1 Front Oil Pump Oil Seal

      Rotate the torque converter assembly approximately 180° and engage the splines of the stator shaft with the stator assembly.

      Note


      • Do not damage the front oil pump oil seal.

      • Install the torque converter assembly to the input shaft while keeping it horizontal.

    4. B007518C01
      *1 Front Oil Pump Oil Seal

      Rotate the torque converter assembly approximately 180° again, align the matchmark on the torque converter assembly with the one on the automatic transmission case sub-assembly and insert the key of the torque converter assembly into the groove of the oil pump drive gear.

      Note


      • Do not push the torque converter assembly excessively when rotating it.

      • Do not damage the front oil pump oil seal.

      • Install the torque converter assembly to the input shaft while keeping it horizontal.

    5. B007530N02

      Using a vernier caliper and straightedge, measure the dimension (B) shown in the illustration and check that the dimension (B) is more than the dimension (A), which was measured in the previous step.

      Standard
      Dimension (A) + 1 mm (0.0394 in.) or more

      Note


      • Make sure to deduct the thickness of the straightedge.

      • If the automatic transmission assembly is installed to the engine assembly with the torque converter assembly not sufficiently inserted, the torque converter assembly may be damaged.

  2. INSTALL REAR ENGINE MOUNTING INSULATOR ASSEMBLY


    1. B00772AC03
      *a Claw
      B0073AQ Vehicle Front

      Install the rear engine mounting insulator assembly to the automatic transmission assembly with the 4 bolts.

      Torque:
      40 N*m  { 408 kgf*cm, 30 ft.*lbf }

      Tech Tips

      Make sure that the claw is facing the front of the vehicle.

  3. INSTALL AUTOMATIC TRANSMISSION ASSEMBLY


    1. B0077ZQC01
      *1 Drive Plate and Ring Gear Sub-assembly
      *2 Crankshaft
      *a Torque Converter Assembly Centerpiece
      B0073AQ Clutch Spline Grease

      Apply clutch spline grease to the circumference of the part of the crankshaft that contacts the torque converter assembly centerpiece.

      Clutch Spline Grease
      Toyota Genuine Clutch Spline Grease or equivalent
      Maximum Grease Amount
      Approximately 1 g (0.0353 oz)
    2. B0077I4C01
      *a Mark

      Make sure that the mark is positioned as shown in the illustration.

    3. B0076FAN01

      Confirm that the 2 knock pins are installed to the engine assembly and are not damaged.

    4. While keeping the engine assembly and automatic transmission assembly horizontal, align the 2 knock pins with the holes in the automatic transmission assembly and install the automatic transmission assembly with the 9 bolts.

      Torque:
      Bolt (A)
      37 N*m  { 377 kgf*cm, 27 ft.*lbf }
      Bolt (B), (C)
      71 N*m  { 724 kgf*cm, 52 ft.*lbf }

      Note


      • When tightening the bolts, make sure that the contact surfaces of the engine assembly and the automatic transmission assembly are in close contact with one another.

      • Do not use excessive force when installing the automatic transmission assembly.

      • Check that the torque converter assembly rotates.

      • Make sure that the wire harness or other similar items are not pinched between the contact surfaces.

      • In order to protect the automatic transmission oil pan sub-assembly, place attachments on the transmission jack.

      • Make sure that the attachments and automatic transmission oil pan sub-assembly are centered on the transmission jack.

      • To prevent the automatic transmission oil pan sub-assembly from being deformed, do not place any attachments under the automatic transmission oil pan sub-assembly.

      • Secure the automatic transmission assembly to the transmission jack using a belt, etc. to prevent it from falling.

      Tech Tips

      Bolt Length

      • Bolt (A): 43 mm (1.69 in.)

      • Bolt (B): 50 mm (1.97 in.)

      • Bolt (C): 70 mm (2.76 in.)

  4. CONNECT WATER BY-PASS HOSE


    1. Tilt down the automatic transmission assembly.

      Note

      Make sure that the engine assembly does not contact the vehicle body when tilting the automatic transmission assembly.

    2. Connect the water by-pass hose and No. 2 water by-pass hose to the transmission oil cooler and slide the 2 clips to secure them.

    3. Connect the hose clamp to the automatic transmission assembly with the bolt.

      Torque:
      20 N*m  { 204 kgf*cm, 15 ft.*lbf }

  5. CONNECT WIRE HARNESS


    1. Connect the park/neutral position switch assembly connector.

    2. Connect the transmission wire connector.

      Tech Tips

      Push up the lever until the claw of the transmission wire connector makes a click sound.

    3. Install the wire harness to the automatic transmission assembly with the nut.

      Torque:
      10 N*m  { 102 kgf*cm, 7 ft.*lbf }

    4. Engage the 4 clamps.

    5. Connect the breather plug hose to the wire harness.

  6. CONNECT NO. 2 EARTH WIRE


    1. Connect the No. 2 earth wire to the automatic transmission assembly with the bolt.

      Torque:
      13 N*m  { 133 kgf*cm, 10 ft.*lbf }

  7. INSTALL REAR ENGINE MOUNTING MEMBER


    1. Temporarily install the rear engine mounting member to the rear No.1 engine mounting insulator with the 4 nuts.

    2. Install the rear engine mounting member to the vehicle body with the 4 bolts.

      Torque:
      34.7 N*m  { 354 kgf*cm, 26 ft.*lbf }

    3. Fully tighten the 4 nuts.

      Torque:
      13 N*m  { 133 kgf*cm, 10 ft.*lbf }

  8. INSTALL FLOOR SHIFT GEAR SHIFTING ROD SUB-ASSEMBLY


    1. B007366C01
      *a Pin

      Install the floor shift gear shifting rod sub-assembly to the transmission control shaft lever RH with the pin.

    2. Install a new clip.

    3. B0074HWC01
      *1 Transmission Control Shaft Lever RH
      *a P
      *b R
      *c N

      Turn the transmission control shaft lever RH counterclockwise until it stops, then turn it clockwise 2 notches.

    4. Move the shift lever to N.

    5. B0075PGC01
      *a Lever
      B0077IM Pushing the lever rearward

      Connect the floor shift gear shifting rod sub-assembly to the lever of the transmission floor shift assembly.

    6. Temporarily install the nut to the lever of the transmission floor shift assembly.

    7. Tighten the nut while lightly pushing the lever of the transmission floor shift assembly toward the rear of the vehicle.

      Torque:
      12.8 N*m  { 131 kgf*cm, 9 ft.*lbf }

      Note

      Do not push the lever of the transmission floor shift assembly too hard.

  9. INSTALL DRIVE PLATE AND TORQUE CONVERTER ASSEMBLY SETTING BOLT


    1. Turn the crankshaft to gain access to the installation locations of the 6 drive plate and torque converter assembly setting bolts and install each bolt while holding the crankshaft pulley with SST.

      SST
      09213-70011   ( 09213-70020 )
      Torque:
      41 N*m  { 418 kgf*cm, 30 ft.*lbf }

      Note

      First install the black colored bolt, and then the remaining 5 silver colored bolts.

  10. INSTALL FLYWHEEL HOUSING SIDE COVER


    1. Install the flywheel housing side cover to the engine assembly.

      Note

      Make sure that the flywheel housing side cover is securely installed.

  11. INSTALL EXHAUST MANIFOLD

    Click here

  12. INSTALL STARTER ASSEMBLY

    Click here

  13. INSTALL PROPELLER WITH CENTER BEARING SHAFT ASSEMBLY

    Click here

  14. INSTALL INTAKE AIR SURGE TANK ASSEMBLY

    Click here

  15. ADD ENGINE COOLANT

    Click here

  16. ADD AUTOMATIC TRANSMISSION FLUID

    Click here

  17. CONNECT CABLE TO NEGATIVE BATTERY TERMINAL

    Note

    When disconnecting the cable, some systems need to be initialized after the cable is reconnected.

    Click here

  18. INSPECT FOR COOLANT LEAK

    Click here

  19. INSPECT SHIFT LEVER POSITION

    Click here

  20. INSPECT FOR EXHAUST GAS LEAK

    Click here

  21. INSTALL NO. 2 ENGINE UNDER COVER (w/ No.2 Engine Under Cover)

    Click here

  22. INSTALL FRONT SUSPENSION MEMBER BRACE

    Click here

  23. INSTALL NO.1 ENGINE UNDER COVER ASSEMBLY

    Click here

  24. RESET MEMORY

    Click here