AUTOMATIC TRANSMISSION SYSTEM(for 2GR-FKS) Shift Paddle Switch Circuit

DESCRIPTION

When the shift lever is in D, operating the "-" side shift paddle switch will cause the transmission to enter fixed range mode which restricts the highest gear. By operating the shift paddle switches "+" (up-shift) or "-" (down-shift), the shift range can be changed.

When the vehicle is being driven in D position (fixed range mode), if the vehicle is stopped or the accelerator pedal is kept steady for a certain period of time with the transmission in the same gear, the vehicle will change back automatically to normal D position operation.

When the shift lever is in M, it is possible to make use of the highest engine speeds by holding the vehicle in a gear. Gear hold control means that gear shifts will not be performed as long as the paddle switches are not operated in either the "+" (up-shift), or "-" (down-shift) direction.

WIRING DIAGRAM

Figure 1. w/o Dynamic Radar Cruise Control System:

B007559E04

Figure 2. w/ Dynamic Radar Cruise Control System:

B0075PAE23

PROCEDURE


  1. CHECK HARNESS AND CONNECTOR (SHIFT PADDLE SWITCH - ECM)


    1. Disconnect the A96 ECM connector.

    2. Measure the resistance according to the value(s) in the table below.

      Standard Resistance
      Tester Connection Condition Specified Condition
      A96-38 (SFTU) - Body ground Pull continuously "+" (Up-shift) Below 2.5 Ω
      Release "+" (Up-shift) 1 MΩ or higher
      A96-37 (SFTD) - Body ground Pull continuously "-" (Down-shift) Below 2.5 Ω
      Release "-" (Down-shift) 1 MΩ or higher
      Result
      Proceed to
      OK
      NG

    OK

    PROCEED TO NEXT SUSPECTED AREA SHOWN IN PROBLEM SYMPTOMS TABLE Click here

    NG

  2. CHECK HARNESS AND CONNECTOR (SPIRAL CABLE SUB-ASSEMBLY - BODY GROUND)


    1. Disconnect the O25 spiral cable sub-assembly connector.

    2. Measure the resistance according to the value(s) in the table below.

      Standard Resistance
      Tester Connection Condition Specified Condition
      O25-2 (ECC) - Body ground Always Below 1 Ω
      Result
      Proceed to
      OK
      NG

    NG

    REPAIR OR REPLACE HARNESS OR CONNECTOR

    OK

  3. CHECK HARNESS AND CONNECTOR (SPIRAL CABLE SUB-ASSEMBLY - ECM)


    1. Disconnect the O25 spiral cable sub-assembly connector.

    2. Disconnect the A96 ECM connector.

    3. Measure the resistance according to the value(s) in the table below.

      Standard Resistance
      Tester Connection Condition Specified Condition
      A96-38 (SFTU) - O25-8 (SUP) Always Below 1 Ω
      A96-37 (SFTD) - O25-1 (SDN) Always Below 1 Ω
      A96-38 (SFTU) or O25-8 (SUP) - Body ground Always 10 kΩ or higher
      A96-37 (SFTD) or O25-1 (SDN) - Body ground Always 10 kΩ or higher
      Result
      Proceed to
      OK
      NG

    NG

    REPAIR OR REPLACE HARNESS OR CONNECTOR

    OK

  4. INSPECT SPIRAL CABLE SUB-ASSEMBLY


    1. Inspect the spiral cable sub-assembly.

      Click here

      Result
      Proceed to
      OK
      NG

    NG

    REPLACE SPIRAL CABLE SUB-ASSEMBLY Click here

    OK

  5. INSPECT SHIFT PADDLE SWITCH LH (TRANSMISSION SHIFT SWITCH ASSEMBLY)


    1. B0077NWC07
      *a

      Component without harness connected

      (Shift Paddle Switch LH (Transmission Shift Switch Assembly))

      Remove the transmission shift switch assembly (shift paddle switch LH).

      Click here

    2. Measure the resistance according to the value(s) in the table below.

      Standard Resistance
      Tester Connection Condition Specified Condition
      B-1 (SDN) - B-2 (ECC) Pull continuously "-" (Down-shift) Below 2.5 Ω
      Release "-" (Down-shift) 1 MΩ or higher
      Result
      Proceed to
      OK
      NG

    NG

    REPLACE SHIFT PADDLE SWITCH LH (TRANSMISSION SHIFT SWITCH ASSEMBLY) Click here

    OK

  6. INSPECT SHIFT PADDLE SWITCH RH (TRANSMISSION SHIFT SWITCH ASSEMBLY)


    1. B0076TKC06
      *a

      Component without harness connected

      (Shift Paddle Switch RH (Transmission Shift Switch Assembly))

      Remove the transmission shift switch assembly (shift paddle switch RH).

      Click here

    2. Measure the resistance according to the value(s) in the table below.

      Standard Resistance
      Tester Connection Condition Specified Condition
      A-3 (SUP) - A-2 (ECC) Pull continuously "+" (Up-shift) Below 2.5 Ω
      Release "+" (Up-shift) 1 MΩ or higher
      Result
      Result Proceed to
      OK (w/o Dynamic Radar Cruise Control System) A
      OK (w/ Dynamic Radar Cruise Control System) B
      NG C

    B

    INSPECT NO. 1 SWITCH WIRE Click here

    C

    REPLACE SHIFT PADDLE SWITCH RH (TRANSMISSION SHIFT SWITCH ASSEMBLY) Click here

    A

  7. INSPECT NO. 1 SWITCH WIRE


    1. B0074VIC15
      *a

      Front view of wire harness connector

      (to No. 2 Switch Wire)

      Install the transmission shift switch assembly (shift paddle switch LH) and transmission shift switch assembly (shift paddle switch RH).

      Click here

    2. Disconnect the n1 No. 1 switch wire connector.

    3. Measure the resistance according to the value(s) in the table below.

      Standard Resistance
      Tester Connection Condition Specified Condition
      n1-1 (SUP) - n1-3 (ECC) Pull continuously "+" (Up-shift) Below 2.5 Ω
      Release "+" (Up-shift) 1 MΩ or higher
      n1-2 (SDN) - n1-3 (ECC) Pull continuously "-" (Down-shift) Below 2.5 Ω
      Release "-" (Down-shift) 1 MΩ or higher
      Result
      Proceed to
      OK
      NG

    NG

    REPLACE NO. 1 SWITCH WIRE Click here

    OK

  8. INSPECT NO. 2 SWITCH WIRE


    1. B0076N9C19
      *a

      Front view of wire harness connector

      (to Spiral Cable Sub-assembly)

      Connect the n1 No. 1 switch wire connector.

    2. Disconnect the n2 No. 2 switch wire connector.

    3. Measure the resistance according to the value(s) in the table below.

      Standard Resistance
      Tester Connection Condition Specified Condition
      n2-1 (SUP) - n2-4 (ECC) Pull continuously "+" (Up-shift) Below 2.5 Ω
      Release "+" (Up-shift) 1 MΩ or higher
      n2-3 (SDN) - n2-4 (ECC) Pull continuously "-" (Down-shift) Below 2.5 Ω
      Release "-" (Down-shift) 1 MΩ or higher
      Result
      Proceed to
      OK
      NG

    OK

    PROCEED TO NEXT SUSPECTED AREA SHOWN IN PROBLEM SYMPTOMS TABLE Click here

    NG

    REPLACE NO. 2 SWITCH WIRE Click here

  9. INSPECT NO. 1 SWITCH WIRE


    1. B0076N9C20
      *a

      Front view of wire harness connector

      (to Spiral Cable Sub-assembly)

      Install the transmission shift switch assembly (shift paddle switch LH) and transmission shift switch assembly (shift paddle switch RH).

      Click here

    2. Disconnect the z19 No. 1 switch wire connector.

    3. Measure the resistance according to the value(s) in the table below.

      Standard Resistance
      Tester Connection Condition Specified Condition
      z19-1 (SUP) - z19-4 (ECC) Pull continuously "+" (Up-shift) Below 2.5 Ω
      Release "+" (Up-shift) 1 MΩ or higher
      z19-3 (SDN) - z19-4 (ECC) Pull continuously "-" (Down-shift) Below 2.5 Ω
      Release "-" (Down-shift) 1 MΩ or higher
      Result
      Proceed to
      OK
      NG

    OK

    PROCEED TO NEXT SUSPECTED AREA SHOWN IN PROBLEM SYMPTOMS TABLE Click here

    NG

    REPLACE NO. 1 SWITCH WIRE Click here