AUTOMATIC TRANSMISSION SYSTEM(for 8AR-FTS), Diagnostic DTC:P076A7F

DTC Code DTC Name
P076A7F Shift Solenoid "H" Control Actuator Stuck Off

DESCRIPTION

Based on signals from the transmission revolution sensors (NT, NC3 and SP2), the actual gear is detected.

If the detected gear is different than the commanded gear, the ECM detects related mechanical problems in the shift solenoid valves, transmission valve body assembly and automatic transmission assembly (clutch, brake, gear, etc.).

Tech Tips

Actual gear when a malfunction occurs in solenoid (SC1) valve (without fail-safe control):
ECM commanded gear 1st 2nd 3rd 4th 5th 6th 7th 8th
Actual gear during SC1 stuck OFF malfunction

1st

(3rd)*

 2nd 3rd 4th 5th 6th 7th 8th

*: With D1 or M1 range (1st gear) selected

DTC No. Detection Item DTC Detection Condition Trouble Area MIL Memory Note
P076A7F Shift Solenoid "H" Control Actuator Stuck Off

1. Diagnosis Condition, 2. Malfunction Status, 3. Malfunction Time, 4. Other


  1. Engine coolant temperature is 40°C (104°F) or more, ATF temperature is -10°C (14°F) or more, and the vehicle is driven with D1 or M1 range (1st gear) (no malfunctions are detected in solenoid (SL1, SL2, SL3, SL4, SL5, SC1 and SC2) valves, transmission revolution sensors (NT, NC3, SP2), water temperature sensor, oil temperature sensor, knock control sensor, electronic throttle, or CAN2)

  2. When the ECM commands the transmission to shift to 1st gear, the actual gear changes to 3rd gear.

  3. Malfunction status continues for 0.6 seconds or more

  4. 2-trip detection logic

  • Solenoid (SC1) valve

  • Solenoid (SC2) valve

  • Solenoid (SL1) valve

  • Solenoid (SL2) valve

  • Solenoid (SL3) valve

  • Solenoid (SL4) valve

  • Solenoid (SLT) valve

  • Transmission valve body assembly

  • Torque converter assembly

  • Automatic transmission assembly (clutch, brake, gear, etc.)

 Comes on DTC stored

SAE Code:

P076B

MONITOR DESCRIPTION

This DTC indicates a "stuck OFF" malfunction of the solenoid (SC1) valve.

The ECM commands gear shifts by turning the shift solenoid valves on or off. When the gear commanded by the ECM and the actual gear are not the same, the ECM illuminates the MIL and stores a DTC.

CAUTION / NOTICE / HINT

Note

Perform registration and/or initialization when parts related to the automatic transmission are replaced.

Click here

Tech Tips

After performing repair, clear the DTCs and perform the following procedure to check that DTCs are not output.


  1. While the vehicle is being driven, move the shift lever to M, select the M1 (1st gear) range and perform an engine brake.

  2. Check for DTCs again.

    Click here

PROCEDURE


  1. CHECK DTC OUTPUT (IN ADDITION TO DTC P076A7F)


    1. Connect the GTS to the DLC3.

    2. Turn the engine switch on (IG).

    3. Turn the GTS on.

    4. Enter the following menus: Powertrain / Transmission / Trouble Codes.


      Powertrain > Transmission > Trouble Codes

    5. Read the DTCs using the GTS.

      Result
      Result Proceed to
      DTC P076A7F and P07457F, P076A7E, P07757F, P07957F, P08CC7E, P08CC7F, P27137F and/or P28077F are output A
      Only DTC P076A7F is output B
      DTCs other than P07457F, P076A7E, P076A7F, P07757F, P07957F, P08CC7E, P08CC7F, P27137F and P28077F are also output C

      Tech Tips

      If any DTCs other than P07457F, P076A7E, P076A7F, P07757F, P07957F, P08CC7E, P08CC7F, P27137F and P28077F are output, perform troubleshooting for those DTCs first.


    B

    GO TO STEP 3 Click here

    C

    GO TO DTC CHART Click here

    A

  2. CLEAR DTC AND PERFORM STALL SPEED TEST


    1. Clear the DTCs.

      Click here

      Tech Tips

      Write down the currently output DTCs before clearing them.


      Powertrain > Transmission > Clear DTCs

    2. Perform the stall speed test.

      Click here

      Result
      Test Condition Proceed to
      Stall speed test can be performed A
      Stall speed test cannot be performed B

    B

    GO TO STEP 5 Click here

    A

  3. INSPECT SOLENOID (SC1) AND (SC2) VALVE


    1. B0075VLC01
      *1 Solenoid (SC1) and (SC2) Valves

      Remove the solenoid (SC1) and (SC2) valves.

      Click here

    2. Measure the resistance according to the value(s) in the table below.

      Standard Resistance
      Tester Connection Condition Specified Condition
      Terminal of solenoid (SC1) valve connector - Solenoid (SC1) valve body 20°C (68°F) 11 to 15 Ω
      Terminal of solenoid (SC2) valve connector - Solenoid (SC2) valve body 20°C (68°F) 11 to 15 Ω

    3. Connect a positive (+) lead from the battery to the terminal of the solenoid valve connector, and a negative (-) lead to the solenoid body. Check that the valve moves and makes an operating sound.

      OK
      Valve moves and makes an operating sound.
      Result
      Proceed to
      OK
      NG

    NG

    REPLACE SOLENOID (SC1) OR (SC2) VALVE Click here

    OK

  4. INSPECT SOLENOID (SL1), (SL2), (SL3) AND (SL4) VALVE


    1. B007782C46
      *a

      Component without harness connected

      (Solenoid (SL1), (SL2), (SL3) and (SL4) Valves)

      Remove the solenoid (SL1), (SL2), (SL3) and (SL4) valves.

      Click here

    2. Measure the resistance according to the value(s) in the table below.

      Standard Resistance
      Tester Connection Condition Specified Condition
      Terminal 1 of the solenoid (SL1) valve - terminal 2 20°C (68°F) 5.0 to 5.6 Ω
      Terminal 1 of the solenoid (SL2) valve - terminal 2 20°C (68°F) 5.0 to 5.6 Ω
      Terminal 1 of the solenoid (SL3) valve - terminal 2 20°C (68°F) 5.0 to 5.6 Ω
      Terminal 1 of the solenoid (SL4) valve - terminal 2 20°C (68°F) 5.0 to 5.6 Ω

    3. Connect a positive (+) lead from the battery with a 21 W bulb to terminal 2 and a negative (-) lead to terminal 1 of the solenoid valve connector. Check that the valve moves and makes an operating sound.

      OK
      Valve moves and makes an operating sound.
      Result
      Proceed to
      OK
      NG

    NG

    REPLACE SOLENOID (SL1), (SL2), (SL3) OR (SL4) VALVE Click here

    OK

  5. INSPECT SOLENOID(SLT) VALVE


    1. B007782C46
      *a

      Component without harness connected

      (Solenoid (SLT) Valve)

      Remove the solenoid (SLT) valve.

      Click here

    2. Measure the resistance according to the value(s) in the table below.

      Standard Resistance
      Tester Connection Condition Specified Condition
      Terminal 1 of the solenoid (SLT) valve - terminal 2 20°C (68°F) 5.0 to 5.6 Ω

    3. Connect a positive (+) lead from the battery with a 21 W bulb to terminal 2 and a negative (-) lead to terminal 1 of the solenoid valve connector. Check that the valve moves and makes an operating sound.

      OK
      Valve moves and makes an operating sound.
      Result
      Proceed to
      OK
      NG

    NG

    REPLACE SOLENOID (SLT) VALVE Click here

    OK

  6. INSPECT TRANSMISSION VALVE BODY ASSEMBLY


    1. Check the transmission valve body assembly.

      Click here

      OK
      There is no foreign matter on each valve and they operate smoothly.
      Result
      Proceed to
      OK
      NG

    NG

    REPAIR OR REPLACE TRANSMISSION VALVE BODY ASSEMBLY Click here

    OK

  7. INSPECT TORQUE CONVERTER ASSEMBLY


    1. Check the torque converter assembly.

      Click here

      OK
      The torque converter operates normally.
      Result
      Proceed to
      OK
      NG

    NG

    REPLACE TORQUE CONVERTER ASSEMBLY Click here

    OK

  8. REPAIR OR REPLACE AUTOMATIC TRANSMISSION ASSEMBLY


    1. Repair or replace the automatic transmission assembly.

      Click here

      Result
      Proceed to
      NEXT

    NEXT

    PERFORM A/T CODE REGISTRATION Click here