OIL AND OIL FILTER REPLACEMENT

CAUTION / NOTICE / HINT

CAUTION:


  • Prolonged and repeated contact with engine oil will result in the removal of natural oils from the skin, leading to dryness, irritation and dermatitis. In addition, used engine oil contains potentially harmful contaminants which may cause skin cancer.

  • Wear protective clothing and gloves. Avoid contact with used oil. If contact occurs, wash your skin thoroughly with soap or waterless hand cleaner. Never use gasoline, thinners, or solvents to wash the skin.

  • In order to protect the environment, dispose of used oil and used oil filters at designated disposal sites only.

PROCEDURE


  1. DRAIN ENGINE OIL


    1. Remove the oil filler cap sub-assembly.

    2. Remove the oil pan drain plug and gasket, and drain the engine oil into a container.

    3. Clean the oil pan drain plug.

    4. Install a new gasket to the oil pan drain plug.

    5. Install the oil pan drain plug.

      Torque:
      40 N*m  { 408 kgf*cm, 30 ft.*lbf }

  2. REMOVE OIL FILTER CAP ASSEMBLY


    1. B0075EFC04
      *a Pipe
      *b Hose

      Connect a hose with an inside diameter of 15 mm (0.591 in.) to the pipe.

    2. A01VRPN

      Remove the oil filter drain plug from the oil filter cap assembly.

    3. B0075W3C03
      *1 Oil Filter Cap Assembly
      *2 O-ring
      *a Pipe

      Insert the pipe with hose into the oil filter cap assembly.

      Note

      Be sure to insert the pipe with the O-ring installed to the oil filter cap assembly.

      Tech Tips

      Place the hose end into a container before draining the engine oil from the hose.

    4. A01VRKT

      Make sure that the engine oil is completely drained, and remove the pipe with hose and O-ring.

      Tech Tips

      Pull the pipe with hose as shown in the illustration to remove it.

    5. B007785C02
      *1 Oil Filter Bracket Clip

      Using SST, remove the oil filter cap assembly.

      SST
      09228-06501

      Note

      Do not remove the oil filter bracket clip.

    6. B00770PC05
      *1 Oil Filter Element
      *2 Oil Filter Cap Assembly
      *3 O-ring

      Remove the oil filter element and O-ring from the oil filter cap assembly.

      Note

      Do not use any tools to remove the O-ring in order to prevent the oil filter cap assembly from being damaged. Be sure to remove it by hand.

  3. INSTALL OIL FILTER CAP ASSEMBLY


    1. Clean the inside of the oil filter cap assembly, the threads and O-ring groove.

    2. B0075Q9C11
      *1 O-ring
      *a Correct
      *b Incorrect

      Apply a small amount of engine oil to a new O-ring and install it to the oil filter cap assembly.

      Note


      • Be sure to install the O-ring in the proper location, otherwise engine oil may leak.

      • Do not twist the O-ring.

    3. Set a new oil filter element in the oil filter cap assembly.

    4. Remove any dirt or foreign matter from the installation surface of the engine.

    5. Apply a small amount of engine oil to the O-ring again and install the oil filter cap assembly.

      Note

      Make sure that the O-ring does not get caught between the parts.

    6. B0072ONC02
      *1 Oil Filter Cap Assembly
      *2 O-ring
      *3 Oil Filter Bracket
      *a No Gap

      Using SST, tighten the oil filter cap assembly.

      SST
      09228-06501
      Torque:
      25 N*m  { 255 kgf*cm, 18 ft.*lbf }

      Note


      • After tightening the oil filter cap assembly, make sure that there is no gap and that the O-ring is not protruding.

      • Do not cross thread the oil filter cap assembly.

    7. B0077PJC02
      *1 O-ring

      Apply a small amount of engine oil to a new O-ring and install it to the oil filter cap assembly.

      Note

      Remove any dirt or foreign matter from the installation surface.

    8. Install the oil filter drain plug to the oil filter cap assembly.

      Torque:
      12.5 N*m  { 127 kgf*cm, 9 ft.*lbf }

      Note

      Make sure that the O-ring does not get caught between the parts.

  4. ADD ENGINE OIL


    1. Add clean engine oil and install the oil filler cap sub-assembly.

      Standard Oil Grade
      Oil Grade Oil Viscosity (SAE)
      "Toyota Genuine Motor Oil SAE 0W-20 for Downsized Turbo Gasoline Engines" or API grade SL "Energy-Conserving", SM "Energy-Conserving" or SN "Resource-Conserving" or ILSAC multigrade engine oil

      • 0W-20

      • 5W-20

      • 5W-30

      • 10W-30
      Standard Oil Grade (Destination package for Europe)
      Oil Grade Oil Viscosity (SAE)
      "Toyota Genuine Motor Oil SAE 0W-20 for Downsized Turbo Gasoline Engines" or API grade SL "Energy-Conserving", SM "Energy-Conserving" or SN "Resource-Conserving" or ILSAC multigrade engine oil

      • 0W-20

      • 5W-30
      Standard Oil Grade (Destination package for China)
      Oil Grade Oil Viscosity (SAE)
      "Toyota Genuine Motor Oil SAE 0W-20 for Downsized Turbo Gasoline Engines" or API grade SL "Energy-Conserving", SM "Energy-Conserving" or SN "Resource-Conserving" or ILSAC multigrade engine oil

      • 0W-20

      • 5W-20

      • 5W-30
      Standard Capacity:
      Item Specified Condition
      Drain and refill with oil filter change 4.6 liters (4.9 US qts, 4.0 Imp. qts)
      Drain and refill without oil filter change 4.3 liters (4.5 US qts, 3.8 Imp. qts)
      Dry fill 5.5 liters (5.8 US qts, 4.8 Imp. qts)

  5. INSPECT FOR ENGINE OIL LEAK


    1. Start the engine. Make sure that there are no engine oil leaks from the area that was worked on.

  6. CHECK ENGINE OIL LEVEL

    Click here