FUEL TANK(w/ Canister Pump Module) INSTALLATION

PROCEDURE


  1. INSTALL FUEL TANK PROTECTOR SUB-ASSEMBLY


    1. Install the No. 2 fuel tank protector and No. 3 fuel tank protector to the fuel tank assembly.

    2. Install the No. 1 fuel tank protector sub-assembly to the fuel tank assembly.

      Tech Tips

      Install the No. 1 fuel tank protector sub-assembly after installing the No. 2 fuel tank protector and No. 3 fuel tank protector.

  2. INSTALL FUEL TANK CUSHION


    1. Install the fuel tank bracket, 2 fuel tank cushions and fuel tank cushion set to the fuel tank assembly.

    2. Install 5 new No. 6 fuel tank cushions to the fuel tank assembly.

  3. INSTALL FUEL TUBE


    1. Engage the 2 clamps to install the No. 3 fuel tube clamp and No. 5 fuel tube clamp to the fuel tank assembly.

    2. Engage the 4 clamps to install the fuel tank return tube and fuel tank main tube sub-assembly to the fuel tank assembly.

  4. INSTALL FUEL TANK ASSEMBLY


    1. Set the fuel tank assembly on an engine lifter with attachments.

      Tech Tips

      Using height adjustment attachments and plate lift attachments, keep the fuel tank assembly horizontal.

    2. Using the engine lifter, slowly raise the fuel tank assembly, and then install the fuel tank assembly with the 2 nuts, 4 bolts and 2 No. 1 fuel tank band sub-assemblies.

      Torque:
      Nut
      19.6 N*m  { 200 kgf*cm, 14 ft.*lbf }
      Bolt
      45 N*m  { 459 kgf*cm, 33 ft.*lbf }

      Note


      • Do not drop the fuel tank assembly.

      • When installing the fuel tank assembly, tilt it slightly to prevent it from interfering with the suspension arm or other surrounding parts.

  5. INSTALL REAR BODY MOUNTING CUSHION SUB-ASSEMBLY LH

    Click here

  6. INSTALL REAR BODY MOUNTING CUSHION SUB-ASSEMBLY RH

    Click here

  7. INSTALL PARKING BRAKE CABLE ASSEMBLY


    1. Install the No. 2 parking brake cable assembly and No. 3 parking brake cable assembly with the 2 bolts and 2 nuts.

      Torque:
      Bolt
      19 N*m  { 194 kgf*cm, 14 ft.*lbf }
      Nut
      6.0 N*m  { 61 kgf*cm, 53 in.*lbf }

    2. Engage the 4 clamps.

  8. CONNECT FUEL TANK BREATHER TUBE


    1. B0074SMC03
      *1 Breather Tube Clamp
      *a Retainer
      *b Claw
      B0073AQ Push
      B0077IM Push in

      Push the fuel tank breather tube onto the fuel tank to filler pipe hose and push in the retainer to engage the 2 claws.

      Note


      • Check that there are no scratches or foreign matter around the connecting parts of the fuel tank breather tube connector and fuel tank to filler pipe hose before performing this work.

      • After connecting the fuel tank breather tube, check that the fuel tank breather tube is securely connected by pulling on the fuel tank breather tube.

    2. Engage the clamp to connect the fuel tank breather tube to the breather tube clamp.

  9. CONNECT FUEL CUT OFF VALVE TUBE


    1. B0075IZC02
      *1 No. 1 Evaporation Vent Tube Clamp
      *a Retainer
      B0073AQ Push
      B0077IM Push in

      Push the fuel cut off valve tube onto the fuel tank vent hose and push in the retainer to engage the lock claws.

      Note


      • Check that there are no scratches or foreign matter around the connecting parts of the fuel cut off valve tube connector and fuel tank vent hose before performing this work.

      • After connecting the fuel cut off valve tube, check that the fuel tank breather tube is securely connected by pulling on the fuel cut off valve tube.

    2. Engage the clamp to connect the fuel cut off valve tube to the No. 1 evaporation vent tube clamp.

  10. CONNECT FUEL TANK TO FILLER PIPE HOSE


    1. B0074YZC01
      *a Top

      Connect the fuel tank to filler pipe hose to the fuel tank assembly and tighten the clamp to secure it.

      Tech Tips

      Make sure the clamp bolt is within the area shown in the illustration.

  11. CONNECT FUEL TUBE


    1. B0072Z1C01
      *a Retainer
      *b Fuel Tube Connector
      *c Nylon Tube
      *d O-ring
      *e Fuel Pipe
      *f Claw
      B0073AQ Push
      B0077IM Push in

      Connect the fuel tank return tube and fuel tank main tube sub-assembly on the RH side.

      Note

      Check if there is any damage or foreign matter on the connecting parts of the fuel lines.


      1. Align the fuel tube connector with the fuel pipe, and push them together until the fuel tube connector makes a "click" sound. If it is difficult to push the fuel pipe into the fuel tube connector, apply a small amount of clean engine oil to the tip of the fuel pipe and reinsert it.

      2. Connect the fuel lines and push in the retainer to engage the 2 claws. Check that the fuel pipe and fuel tube connector are securely connected by pulling on them.

    2. for Half Cover Type:


      1. Install the 2 No. 1 fuel tube protectors to the fuel tank return tube and fuel tank main tube sub-assembly on the RH side.

    3. B0076UZC01
      *a Retainer
      *b Fuel Tube Connector
      *c Nylon Tube
      *d O-ring
      *e Fuel Pipe
      *f Claw
      B0073AQ Push
      B0077IM Push in

      Connect the fuel tank main tube sub-assembly on the LH side.

      Note

      Check if there is any damage or foreign matter on the connecting parts of the fuel lines.


      1. Align the fuel tube connector with the fuel pipe, and push them together until the fuel tube connector makes a "click" sound. If it is difficult to push the fuel pipe into the fuel tube connector, apply a small amount of clean engine oil to the tip of the fuel pipe and reinsert it.

      2. Connect the fuel lines and push in the retainer to engage the 2 claws. Check that the fuel pipe and fuel tube connector are securely connected by pulling on them.

    4. for Half Cover Type:


      1. Install the No. 1 fuel tube protector to the fuel tank main tube sub-assembly on the LH side.

  12. INSTALL REAR FLOOR SIDE MEMBER COVER LH (for Half Cover Type)

    Click here

  13. INSTALL REAR FLOOR SIDE MEMBER COVER RH (for Half Cover Type)

    Click here

  14. INSTALL PROPELLER SHAFT WITH CENTER BEARING ASSEMBLY

    Click here

  15. ADD FUEL

  16. INSTALL FUEL TANK VENT TUBE ASSEMBLY

    Click here

  17. INSTALL FUEL SUCTION TUBE WITH PUMP AND GAUGE ASSEMBLY

    Click here