NAVIGATION SYSTEM, Diagnostic DTC:B15C3

DTC Code DTC Name
B15C3 Speaker Output Short

DESCRIPTION

This DTC is stored when a malfunction occurs in the speakers.

DTC No. Detection Item DTC Detection Condition Trouble Area
B15C3 Speaker Output Short A short is detected in the speaker output circuit.

  • Harness or connector

  • Speaker

  • Stereo component amplifier assembly

  • Telematics transceiver*

*: w/ Telematics Transceiver

WIRING DIAGRAM

Figure 1. for 10 Speakers

B0074P1E17
B0077O7E45

Figure 2. for 17 Speakers

B0074P1E18
B0072VSE04

CAUTION / NOTICE / HINT

Note


  • Depending on the parts that are replaced during vehicle inspection or maintenance, performing initialization, registration or calibration may be needed. Refer to Precaution for Navigation System.

    Click here

PROCEDURE


  1. CHECK MODEL


    1. Choose the model to be inspected.

      Result
      Result Proceed to
      for 10 Speakers (w/ Telematics Transceiver) A
      for 10 Speakers (w/o Telematics Transceiver) B
      for 17 Speakers (w/ Telematics Transceiver) C
      for 17 Speakers (w/o Telematics Transceiver) D

    B

    CHECK HARNESS AND CONNECTOR (STEREO COMPONENT AMPLIFIER ASSEMBLY - BODY GROUND) Click here

    C

    CHECK HARNESS AND CONNECTOR (STEREO COMPONENT AMPLIFIER ASSEMBLY - BODY GROUND) Click here

    D

    CHECK HARNESS AND CONNECTOR (STEREO COMPONENT AMPLIFIER ASSEMBLY - BODY GROUND) Click here

    A

  2. CHECK HARNESS AND CONNECTOR (STEREO COMPONENT AMPLIFIER ASSEMBLY - BODY GROUND)


    1. Disconnect the T20 stereo component amplifier assembly connector.

    2. Disconnect the O150 telematics transceiver connector.

    3. Disconnect the O55 front No. 2 speaker assembly LH connector.

    4. Disconnect the R14 and S14 front No. 1 speaker assembly connectors.

    5. Disconnect the O56 front No. 3 speaker assembly connector.

    6. Disconnect the T25 and U35 rear speaker assembly connectors.

    7. Disconnect the T24 rear No. 3 speaker assembly connector.

    8. Measure the resistance according to the value(s) in the table below.

      Standard Resistance
      Tester Connection Condition Specified Condition
      T20-13 (FR+) or O150-2 (SPI+) - Body ground Always 10 kΩ or higher
      T20-28 (FR-) or O150-3 (SPI-) - Body ground Always 10 kΩ or higher
      T20-12 (FL+) or O55-2 (+) - Body ground Always 10 kΩ or higher
      T20-27 (FL-) or O55-1 (-) - Body ground Always 10 kΩ or higher
      T20-5 (WFR+) or R14-1 - Body ground Always 10 kΩ or higher
      T20-20 (WFR-) or R14-2 - Body ground Always 10 kΩ or higher
      T20-4 (WFL+) or S14-1 - Body ground Always 10 kΩ or higher
      T20-19 (WFL-) or S14-2 - Body ground Always 10 kΩ or higher
      T20-7 (CTR+) or O56-2 (+) - Body ground Always 10 kΩ or higher
      T20-22 (CTR-) or O56-1 (-) - Body ground Always 10 kΩ or higher
      T20-9 (RR+) or T25-1 - Body ground Always 10 kΩ or higher
      T20-24 (RR-) or T25-2 - Body ground Always 10 kΩ or higher
      T20-8 (RL+) or U35-1 - Body ground Always 10 kΩ or higher
      T20-23 (RL-) or U35-2 - Body ground Always 10 kΩ or higher
      T20-6 (WF1+) or T24-1 - Body ground Always 10 kΩ or higher
      T20-21 (WF1-) or T24-2 - Body ground Always 10 kΩ or higher
      Result
      Proceed to
      OK
      NG

    NG

    REPAIR OR REPLACE HARNESS OR CONNECTOR

    OK

  3. CHECK HARNESS AND CONNECTOR (TELEMATICS TRANSCEIVER - BODY GROUND)


    1. Disconnect the O150 telematics transceiver connector.

    2. Disconnect the O54 front No. 2 speaker assembly RH connector.

    3. Measure the resistance according to the value(s) in the table below.

      Standard Resistance
      Tester Connection Condition Specified Condition
      O150-5 (SPO+) or O54-2 (+) - Body ground Always 10 kΩ or higher
      O150-6 (SPO-) or O54-1 (-) - Body ground Always 10 kΩ or higher
      Result
      Proceed to
      OK
      NG

    NG

    REPAIR OR REPLACE HARNESS OR CONNECTOR

    OK

  4. INSPECT TELEMATICS TRANSCEIVER


    1. Remove the telematics transceiver.

      Click here

    2. B00771JC05
      *a

      Component without harness connected

      (Telematics Transceiver)

      Measure the resistance according to the value(s) in the table below.

      Standard Resistance
      Tester Connection Condition Specified Condition
      2 (SPI+) - 5 (SPO+) Always Below 1 Ω
      3 (SPI-) - 6 (SPO-) Always Below 1 Ω
      2 (SPI+) - 3 (SPI-) Always 10 kΩ or higher
      5 (SPO+) - 6 (SPO-) Always 10 kΩ or higher
      2 (SPI+) - Body ground Always 10 kΩ or higher
      3 (SPI-) - Body ground Always 10 kΩ or higher
      Result
      Proceed to
      OK
      NG

    OK

    GO TO STEP 10 Click here

    NG

    REPLACE TELEMATICS TRANSCEIVER Click here

  5. CHECK HARNESS AND CONNECTOR (STEREO COMPONENT AMPLIFIER ASSEMBLY - BODY GROUND)


    1. Disconnect the T20 stereo component amplifier assembly connector.

    2. Disconnect the O54 and O55 front No. 2 speaker assembly connectors.

    3. Disconnect the R14 and S14 front No. 1 speaker assembly connectors.

    4. Disconnect the O56 front No. 3 speaker assembly connector.

    5. Disconnect the T25 and U35 rear speaker assembly connectors.

    6. Disconnect the T24 rear No. 3 speaker assembly connector.

    7. Measure the resistance according to the value(s) in the table below.

      Standard Resistance
      Tester Connection Condition Specified Condition
      T20-13 (FR+) or O54-2 (+) - Body ground Always 10 kΩ or higher
      T20-28 (FR-) or O54-1 (-) - Body ground Always 10 kΩ or higher
      T20-12 (FL+) or O55-2 (+) - Body ground Always 10 kΩ or higher
      T20-27 (FL-) or O55-1 (-) - Body ground Always 10 kΩ or higher
      T20-5 (WFR+) or R14-1 - Body ground Always 10 kΩ or higher
      T20-20 (WFR-) or R14-2 - Body ground Always 10 kΩ or higher
      T20-4 (WFL+) or S14-1 - Body ground Always 10 kΩ or higher
      T20-19 (WFL-) or S14-2 - Body ground Always 10 kΩ or higher
      T20-7 (CTR+) or O56-2 (+) - Body ground Always 10 kΩ or higher
      T20-22 (CTR-) or O56-1 (-) - Body ground Always 10 kΩ or higher
      T20-9 (RR+) or T25-1 - Body ground Always 10 kΩ or higher
      T20-24 (RR-) or T25-2 - Body ground Always 10 kΩ or higher
      T20-8 (RL+) or U35-1 - Body ground Always 10 kΩ or higher
      T20-23 (RL-) or U35-2 - Body ground Always 10 kΩ or higher
      T20-6 (WF1+) or T24-1 - Body ground Always 10 kΩ or higher
      T20-21 (WF1-) or T24-2 - Body ground Always 10 kΩ or higher
      Result
      Proceed to
      OK
      NG

    NG

    REPAIR OR REPLACE HARNESS OR CONNECTOR

    OK

  6. INSPECT FRONT NO. 1 SPEAKER ASSEMBLY


    1. Remove the front No. 1 speaker assembly.

      Click here

    2. Inspect the front No. 1 speaker assembly.

      Click here

      Result
      Proceed to
      OK
      NG

    NG

    REPLACE FRONT NO. 1 SPEAKER ASSEMBLY Click here

    OK

  7. INSPECT REAR SPEAKER ASSEMBLY


    1. Remove the rear speaker assembly.

      Click here

    2. Inspect the rear speaker assembly.

      Click here

      Result
      Proceed to
      OK
      NG

    NG

    REPLACE REAR SPEAKER ASSEMBLY Click here

    OK

  8. INSPECT REAR NO. 3 SPEAKER ASSEMBLY


    1. Remove the rear No. 3 speaker assembly.

      Click here

    2. Inspect the rear No. 3 speaker assembly.

      Click here

      Result
      Proceed to
      OK
      NG

    NG

    REPLACE REAR NO. 3 SPEAKER ASSEMBLY Click here

    OK

  9. INSPECT FRONT NO. 3 SPEAKER ASSEMBLY


    1. Remove the front No. 3 speaker assembly.

      Click here

    2. Inspect the front No. 3 speaker assembly.

      Click here

      Result
      Proceed to
      OK
      NG

    NG

    REPLACE FRONT NO. 3 SPEAKER ASSEMBLY Click here

    OK

  10. REPLACE FRONT NO. 2 SPEAKER ASSEMBLY


    1. Remove the front No. 2 speaker assembly.

      Click here

    2. Inspect the front No. 2 speaker assembly.

      Click here

    3. Clear the DTCs.


      Body Electrical > Navigation System > Clear DTCs

    4. Recheck for DTCs and check that no DTCs are output.


      Body Electrical > Navigation System > Trouble Codes
      OK
      No DTCs are output.
      Result
      Proceed to
      OK
      NG

    OK

    END

    NG

    REPLACE STEREO COMPONENT AMPLIFIER ASSEMBLY Click here

  11. CHECK HARNESS AND CONNECTOR (STEREO COMPONENT AMPLIFIER ASSEMBLY - BODY GROUND)


    1. Disconnect the T20 stereo component amplifier assembly connector.

    2. Disconnect the O150 telematics transceiver connector.

    3. Disconnect the O55 front No. 2 speaker assembly LH connector.

    4. Disconnect the R14 and S14 front No. 1 speaker assembly connectors.

    5. Disconnect the O56 front No. 3 speaker assembly connector.

    6. Disconnect the T26 and U36 rear No. 2 speaker assembly connectors.

    7. Disconnect the T23 and U34 rear header speaker assembly connectors.

    8. Disconnect the T24 rear No. 3 speaker assembly connector.

    9. Measure the resistance according to the value(s) in the table below.

      Standard Resistance
      Tester Connection Condition Specified Condition
      T20-13 (FR+) or O150-2 (SPI+) - Body ground Always 10 kΩ or higher
      T20-28 (FR-) or O150-3 (SPI-) - Body ground Always 10 kΩ or higher
      T20-12 (FL+) or O55-2 (+) - Body ground Always 10 kΩ or higher
      T20-27 (FL-) or O55-1 (-) - Body ground Always 10 kΩ or higher
      T20-5 (WFR+) or R14-1 - Body ground Always 10 kΩ or higher
      T20-20 (WFR-) or R14-2 - Body ground Always 10 kΩ or higher
      T20-4 (WFL+) or S14-1 - Body ground Always 10 kΩ or higher
      T20-19 (WFL-) or S14-2 - Body ground Always 10 kΩ or higher
      T20-7 (CTR+) or O56-2 (+) - Body ground Always 10 kΩ or higher
      T20-22 (CTR-) or O56-1 (-) - Body ground Always 10 kΩ or higher
      T20-9 (RR+) or T26-3 (+TW) - Body ground Always 10 kΩ or higher
      T20-24 (RR-) or T26-1 (-TW) - Body ground Always 10 kΩ or higher
      T20-8 (RL+) or U36-3 (+TW) - Body ground Always 10 kΩ or higher
      T20-23 (RL-) or U36-1 (-TW) - Body ground Always 10 kΩ or higher
      T20-11 (SR+) or T23-2 (+) - Body ground Always 10 kΩ or higher
      T20-26 (SR-) or T23-1 (-) - Body ground Always 10 kΩ or higher
      T20-10 (SL+) or U34-2 (+) - Body ground Always 10 kΩ or higher
      T20-25 (SL-) or U34-1 (-) - Body ground Always 10 kΩ or higher
      T20-6 (WF1+) or T24-1 - Body ground Always 10 kΩ or higher
      T20-21 (WF1-) or T24-2 - Body ground Always 10 kΩ or higher
      Result
      Proceed to
      OK
      NG

    NG

    REPAIR OR REPLACE HARNESS OR CONNECTOR

    OK

  12. CHECK HARNESS AND CONNECTOR (TELEMATICS TRANSCEIVER - BODY GROUND)


    1. Disconnect the O150 telematics transceiver connector.

    2. Disconnect the O54 front No. 2 speaker assembly RH connector.

    3. Measure the resistance according to the value(s) in the table below.

      Standard Resistance
      Tester Connection Condition Specified Condition
      O150-5 (SPO+) or O54-2 (+) - Body ground Always 10 kΩ or higher
      O150-6 (SPO-) or O54-1 (-) - Body ground Always 10 kΩ or higher
      Result
      Proceed to
      OK
      NG

    NG

    REPAIR OR REPLACE HARNESS OR CONNECTOR

    OK

  13. CHECK HARNESS AND CONNECTOR (REAR NO. 2 SPEAKER ASSEMBLY - BODY GROUND)


    1. Disconnect the T25 and U35 rear speaker assembly connectors.

    2. Disconnect the T26 and U36 rear No. 2 speaker assembly connectors.

    3. Measure the resistance according to the value(s) in the table below.

      Standard Resistance
      Tester Connection Condition Specified Condition
      T26-4 (+) or T25-1 - Body ground Always 10 kΩ or higher
      T26-2 (-) or T25-2 - Body ground Always 10 kΩ or higher
      U36-4 (+) or U35-1 - Body ground Always 10 kΩ or higher
      U36-2 (-) or U35-2 - Body ground Always 10 kΩ or higher
      Result
      Proceed to
      OK
      NG

    NG

    REPAIR OR REPLACE HARNESS OR CONNECTOR

    OK

  14. INSPECT TELEMATICS TRANSCEIVER


    1. Remove the telematics transceiver.

      Click here

    2. B00771JC05
      *a

      Component without harness connected

      (Telematics Transceiver)

      Measure the resistance according to the value(s) in the table below.

      Standard Resistance
      Tester Connection Condition Specified Condition
      2 (SPI+) - 5 (SPO+) Always Below 1 Ω
      3 (SPI-) - 6 (SPO-) Always Below 1 Ω
      2 (SPI+) - 3 (SPI-) Always 10 kΩ or higher
      5 (SPO+) - 6 (SPO-) Always 10 kΩ or higher
      2 (SPI+) - Body ground Always 10 kΩ or higher
      3 (SPI-) - Body ground Always 10 kΩ or higher
      Result
      Proceed to
      OK
      NG

    OK

    GO TO STEP 20 Click here

    NG

    REPLACE TELEMATICS TRANSCEIVER Click here

  15. CHECK HARNESS AND CONNECTOR (STEREO COMPONENT AMPLIFIER ASSEMBLY - BODY GROUND)


    1. Disconnect the T20 stereo component amplifier assembly connector.

    2. Disconnect the O54 and O55 front No. 2 speaker assembly connectors.

    3. Disconnect the R14 and S14 front No. 1 speaker assembly connectors.

    4. Disconnect the O56 front No. 3 speaker assembly connector.

    5. Disconnect the T26 and U36 rear No. 2 speaker assembly connectors.

    6. Disconnect the T23 and U34 rear header speaker assembly connectors.

    7. Disconnect the T24 rear No. 3 speaker assembly connector.

    8. Measure the resistance according to the value(s) in the table below.

      Standard Resistance
      Tester Connection Condition Specified Condition
      T20-13 (FR+) or O54-2 (+) - Body ground Always 10 kΩ or higher
      T20-28 (FR-) or O54-1 (-) - Body ground Always 10 kΩ or higher
      T20-12 (FL+) or O55-2 (+) - Body ground Always 10 kΩ or higher
      T20-27 (FL-) or O55-1 (-) - Body ground Always 10 kΩ or higher
      T20-5 (WFR+) or R14-1 - Body ground Always 10 kΩ or higher
      T20-20 (WFR-) or R14-2 - Body ground Always 10 kΩ or higher
      T20-4 (WFL+) or S14-1 - Body ground Always 10 kΩ or higher
      T20-19 (WFL-) or S14-2 - Body ground Always 10 kΩ or higher
      T20-7 (CTR+) or O56-2 (+) - Body ground Always 10 kΩ or higher
      T20-22 (CTR-) or O56-1 (-) - Body ground Always 10 kΩ or higher
      T20-9 (RR+) or T26-3 (+TW) - Body ground Always 10 kΩ or higher
      T20-24 (RR-) or T26-1 (-TW) - Body ground Always 10 kΩ or higher
      T20-8 (RL+) or U36-3 (+TW) - Body ground Always 10 kΩ or higher
      T20-23 (RL-) or U36-1 (-TW) - Body ground Always 10 kΩ or higher
      T20-11 (SR+) or T23-2 (+) - Body ground Always 10 kΩ or higher
      T20-26 (SR-) or T23-1 (-) - Body ground Always 10 kΩ or higher
      T20-10 (SL+) or U34-2 (+) - Body ground Always 10 kΩ or higher
      T20-25 (SL-) or U34-1 (-) - Body ground Always 10 kΩ or higher
      T20-6 (WF1+) or T24-1 - Body ground Always 10 kΩ or higher
      T20-21 (WF1-) or T24-2 - Body ground Always 10 kΩ or higher
      Result
      Proceed to
      OK
      NG

    NG

    REPAIR OR REPLACE HARNESS OR CONNECTOR

    OK

  16. CHECK HARNESS AND CONNECTOR (REAR NO. 2 SPEAKER ASSEMBLY - BODY GROUND)


    1. Disconnect the T25 and U35 rear speaker assembly connectors.

    2. Disconnect the T26 and U36 rear No. 2 speaker assembly connectors.

    3. Measure the resistance according to the value(s) in the table below.

      Standard Resistance
      Tester Connection Condition Specified Condition
      T26-4 (+) or T25-1 - Body ground Always 10 kΩ or higher
      T26-2 (-) or T25-2 - Body ground Always 10 kΩ or higher
      U36-4 (+) or U35-1 - Body ground Always 10 kΩ or higher
      U36-2 (-) or U35-2 - Body ground Always 10 kΩ or higher
      Result
      Proceed to
      OK
      NG

    NG

    REPAIR OR REPLACE HARNESS OR CONNECTOR

    OK

  17. INSPECT FRONT NO. 1 SPEAKER ASSEMBLY


    1. Remove the front No. 1 speaker assembly.

      Click here

    2. Inspect the front No. 1 speaker assembly.

      Click here

      Result
      Proceed to
      OK
      NG

    NG

    REPLACE FRONT NO. 1 SPEAKER ASSEMBLY Click here

    OK

  18. INSPECT REAR SPEAKER ASSEMBLY


    1. Remove the rear speaker assembly.

      Click here

    2. Inspect the rear speaker assembly.

      Click here

      Result
      Proceed to
      OK
      NG

    NG

    REPLACE REAR SPEAKER ASSEMBLY Click here

    OK

  19. INSPECT REAR NO. 3 SPEAKER ASSEMBLY


    1. Remove the rear No. 3 speaker assembly.

      Click here

    2. Inspect the rear No. 3 speaker assembly.

      Click here

      Result
      Proceed to
      OK
      NG

    NG

    REPLACE REAR NO. 3 SPEAKER ASSEMBLY Click here

    OK

  20. REPLACE FRONT NO. 2 SPEAKER ASSEMBLY


    1. Remove the front No. 2 speaker assembly.

      Click here

    2. Inspect the front No. 2 speaker assembly.

      Click here

    3. Clear the DTCs.


      Body Electrical > Navigation System > Clear DTCs

    4. Recheck for DTCs and check that no DTCs are output.


      Body Electrical > Navigation System > Trouble Codes
      OK
      No DTCs are output.
      Result
      Proceed to
      OK
      NG

    NG

    REPLACE FRONT NO. 2 SPEAKER ASSEMBLY Click here

    OK

  21. REPLACE FRONT NO. 3 SPEAKER ASSEMBLY


    1. Remove the front No. 3 speaker assembly.

      Click here

    2. Inspect the front No. 3 speaker assembly.

      Click here

    3. Clear the DTCs.


      Body Electrical > Navigation System > Clear DTCs

    4. Recheck for DTCs and check that no DTCs are output.


      Body Electrical > Navigation System > Trouble Codes
      OK
      No DTCs are output.
      Result
      Proceed to
      OK
      NG

    NG

    REPLACE FRONT NO. 3 SPEAKER ASSEMBLY Click here

    OK

  22. REPLACE REAR NO. 2 SPEAKER ASSEMBLY


    1. Remove the rear No. 2 speaker assembly.

      Click here

    2. Inspect the rear No. 2 speaker assembly.

      Click here

    3. Clear the DTCs.


      Body Electrical > Navigation System > Clear DTCs

    4. Recheck for DTCs and check that no DTCs are output.


      Body Electrical > Navigation System > Trouble Codes
      OK
      No DTCs are output.
      Result
      Proceed to
      OK
      NG

    NG

    REPLACE REAR NO. 2 SPEAKER ASSEMBLY Click here

    OK

  23. REPLACE REAR HEADER SPEAKER ASSEMBLY


    1. Remove the rear header speaker assembly.

      Click here

    2. Inspect the rear header speaker assembly.

      Click here

    3. Clear the DTCs.


      Body Electrical > Navigation System > Clear DTCs

    4. Recheck for DTCs and check that no DTCs are output.


      Body Electrical > Navigation System > Trouble Codes
      OK
      No DTCs are output.
      Result
      Proceed to
      OK
      NG

    OK

    END

    NG

    REPLACE STEREO COMPONENT AMPLIFIER ASSEMBLY Click here