CAMSHAFT COMPONENTS
ILLUSTRATION
| *A | w/ Oil Cooler | - | - |
| *1 | NO. 1 WATER BY-PASS PIPE | *2 | NO. 2 ENGINE OIL LEVEL DIPSTICK GUIDE |
| *3 | NO. 2 RADIATOR HOSE SUB-ASSEMBLY | *4 | NO. 1 RADIATOR HOSE |
| *5 | ENGINE OIL LEVEL DIPSTICK | *6 | RADIATOR HOSE CLAMP |
| *7 | IGNITION COIL ASSEMBLY | *8 | BATTERY |
| *9 | BATTERY INSULATOR | *10 | NEGATIVE BATTERY CABLE |
| *11 | POSITIVE BATTERY CABLE | *12 | BATTERY CLAMP |
| *13 | NO. 1 BATTERY TRAY SUPPORT | *14 | O-RING |
 |
N*m (kgf*cm, ft.*lbf): Specified torque | ● | Non-reusable part |
ILLUSTRATION
| *1 | WATER OUTLET SUB-ASSEMBLY | *2 | NO. 2 WATER BY-PASS PIPE |
| *3 | WIRE HARNESS | *4 | VACUUM PUMP ASSEMBLY |
| *5 | OUTLET HEATER WATER HOSE A | *6 | INLET HEATER WATER HOSE A |
| *7 | UNION TO CONNECTOR TUBE HOSE | *8 | WIRE HARNESS CLAMP BRACKET |
| *9 | WATER HOSE SET | *10 | NO. 2 WATER BY-PASS HOSE |
| *11 | NO. 6 WATER BY-PASS HOSE | *12 | O-RING |
| *13 | NO. 2 O-RING | *14 | NO. 3 O-RING |
| |
N*m (kgf*cm, ft.*lbf): Specified torque | ● | Non-reusable part |
ILLUSTRATION
| *1 | NO. 1 ENGINE COVER SUB-ASSEMBLY | *2 | CYLINDER HEAD COVER SUB-ASSEMBLY |
| *3 | SPARK PLUG TUBE GASKET | *4 | VVT SENSOR (for Intake Side of Bank 1) |
| *5 | VVT SENSOR (for Exhaust Side of Bank 1) | *6 | CYLINDER HEAD COVER GASKET |
| *7 | CAMSHAFT BEARING CAP OIL HOLE GASKET RH | *8 | GASKET |
| |
N*m (kgf*cm, ft.*lbf): Specified torque | ● | Non-reusable part |
 |
Adhesive 1324 | ★ | Precoated part |
ILLUSTRATION
| *1 | CYLINDER HEAD COVER SUB-ASSEMBLY LH | *2 | SPARK PLUG TUBE GASKET |
| *3 | OIL FILLER CAP SUB-ASSEMBLY | *4 | GASKET |
| *5 | CYLINDER HEAD COVER GASKET | *6 | CAMSHAFT BEARING CAP OIL HOLE GASKET LH |
| *7 | VVT SENSOR (for Intake Side of Bank 2) | *8 | VVT SENSOR (for Exhaust Side of Bank 2) |
| |
N*m (kgf*cm, ft.*lbf): Specified torque | ● | Non-reusable part |
| |
Adhesive 1324 | ★ | Precoated part |
ILLUSTRATION
| *1 | CAMSHAFT TIMING OIL CONTROL SOLENOID ASSEMBLY (for Intake Side of Bank 1) | *2 | CAMSHAFT TIMING OIL CONTROL SOLENOID ASSEMBLY (for Exhaust Side of Bank 1) |
| *3 | CAMSHAFT TIMING OIL CONTROL SOLENOID ASSEMBLY (for Intake Side of Bank 2) | *4 | CAMSHAFT TIMING OIL CONTROL SOLENOID ASSEMBLY (for Exhaust Side of Bank 2) |
| *5 | WIRE HARNESS CLAMP BRACKET | *6 | O-RING |
| |
N*m (kgf*cm, ft.*lbf): Specified torque | ● | Non-reusable part |
| |
Adhesive 1324 | ★ | Precoated part |
ILLUSTRATION
| *1 | CAMSHAFT | *2 | NO. 2 CAMSHAFT |
| *3 | CAMSHAFT TIMING GEAR ASSEMBLY | *4 | CAMSHAFT TIMING EXHAUST GEAR ASSEMBLY RH |
| *5 | CAMSHAFT TIMING GEAR BOLT (for Intake Side of Bank 1) | *6 | CAMSHAFT TIMING GEAR BOLT (for Exhaust Side of Bank 1) |
| *7 | NO. 1 CAMSHAFT BEARING CAP | *8 | NO. 2 CAMSHAFT BEARING CAP |
| *9 | NO. 5 CAMSHAFT BEARING CAP | *10 | NO. 6 CAMSHAFT BEARING CAP |
| *11 | NO. 8 CAMSHAFT BEARING CAP | *12 | TIMING CHAIN COVER PLATE |
| *13 | NO. 1 CHAIN TENSIONER ASSEMBLY | *14 | NO. 2 CHAIN TENSIONER ASSEMBLY |
| *15 | CHAIN SUB-ASSEMBLY | *16 | FUEL PUMP LIFTER HOUSING |
| *17 | TIMING GEAR OR CHAIN COVER GASKET | *18 | NO. 2 CHAIN SUB-ASSEMBLY (for Bank 1) |
| |
N*m (kgf*cm, ft.*lbf): Specified torque | ● | Non-reusable part |
ILLUSTRATION
| *1 | NO. 3 CAMSHAFT SUB-ASSEMBLY | *2 | NO. 4 CAMSHAFT SUB-ASSEMBLY |
| *3 | CAMSHAFT TIMING GEAR ASSEMBLY | *4 | CAMSHAFT TIMING EXHAUST GEAR ASSEMBLY LH |
| *5 | CAMSHAFT TIMING GEAR BOLT (for Intake Side of Bank 2) | *6 | CAMSHAFT TIMING GEAR BOLT (for Exhaust Side of Bank 2) |
| *7 | NO. 3 CAMSHAFT BEARING CAP | *8 | NO. 4 CAMSHAFT BEARING CAP |
| *9 | NO. 7 CAMSHAFT BEARING CAP | *10 | NO. 8 CAMSHAFT BEARING CAP |
| *11 | NO. 9 CAMSHAFT BEARING CAP | *12 | NO. 3 CHAIN TENSIONER ASSEMBLY |
| *13 | CHAIN SUB-ASSEMBLY | *14 | NO. 2 CHAIN SUB-ASSEMBLY (for Bank 2) |
| |
N*m (kgf*cm, ft.*lbf): Specified torque | - | - |