CAMSHAFT OIL CONTROL SOLENOID REMOVAL

PROCEDURE


  1. REMOVE V-BANK COVER SUB-ASSEMBLY

    Click here

  2. REMOVE ENGINE ROOM SIDE COVER

    Click here

  3. REMOVE COOL AIR INTAKE DUCT SEAL

    Click here

  4. DRAIN ENGINE COOLANT

    Click here

  5. REMOVE NO. 1 RADIATOR HOSE

    Click here

  6. REMOVE WATER OUTLET SUB-ASSEMBLY


    1. B0074GRC01
      *1 No. 6 Water By-pass Hose
      *2 No. 15 Water By-pass Hose
      *3 No. 2 Water By-pass Hose

      w/o Oil Cooler:


      1. Slide the clip and disconnect the No. 6 water by-pass hose from the water outlet sub-assembly.

      2. Slide the clip and disconnect the No. 15 water by-pass hose from the water inlet sub-assembly with thermostat.

      3. Disengage the clamp to separate the No. 15 water by-pass hose from the water outlet sub-assembly.

      4. Slide the clip and disconnect the No. 2 water by-pass hose from the water outlet sub-assembly.

    2. B0077F8C01
      *1 No. 6 Water By-pass Hose
      *2 No. 14 Water By-pass Hose
      *3 No. 2 Water By-pass Hose

      w/ Oil Cooler:


      1. Slide the clip and disconnect the No. 6 water by-pass hose from the water outlet sub-assembly.

      2. Slide the clip and disconnect the No. 14 water by-pass hose from the No. 1 water by-pass pipe.

      3. Disengage the clamp to separate the No. 14 water by-pass hose from the water outlet sub-assembly.

      4. Slide the clip and disconnect the No. 2 water by-pass hose from the water outlet sub-assembly.

    3. B0074LT

      Remove the 2 bolts and water outlet sub-assembly from the timing chain cover assembly.

    4. B00738M

      Remove the O-ring from the No. 1 water outlet pipe.

  7. REMOVE CAMSHAFT TIMING OIL CONTROL SOLENOID ASSEMBLY (for Intake Side of Bank 1)


    1. B007734

      Disconnect the camshaft timing oil control solenoid assembly connector.

    2. Remove the 2 bolts and camshaft timing oil control solenoid assembly from the timing chain cover assembly.

      Note

      If the camshaft timing oil control solenoid assembly has been struck or dropped, replace it.

    3. Remove the O-ring from the camshaft timing oil control solenoid assembly.

      Note


      • If the O-ring comes off in the timing chain cover assembly, make sure to remove it.

      • Do not drop the O-ring into the timing chain cover assembly.

  8. REMOVE CAMSHAFT TIMING OIL CONTROL SOLENOID ASSEMBLY (for Exhaust Side of Bank 1)


    1. B00777K

      Remove the bolt and separate the wire harness clamp bracket from the timing chain cover assembly.

    2. B0074PB

      Disconnect the camshaft timing oil control solenoid assembly connector.

    3. Remove the 2 bolts and camshaft timing oil control solenoid assembly from the timing chain cover assembly.

      Note

      If the camshaft timing oil control solenoid assembly has been struck or dropped, replace it.

    4. Remove the O-ring from the camshaft timing oil control solenoid assembly.

      Note


      • If the O-ring comes off in the timing chain cover assembly, make sure to remove it.

      • Do not drop the O-ring into the timing chain cover assembly.

  9. REMOVE CAMSHAFT TIMING OIL CONTROL SOLENOID ASSEMBLY (for Intake Side of Bank 2)


    1. B0073ZT

      Disconnect the camshaft timing oil control solenoid assembly connector.

    2. Remove the 2 bolts and camshaft timing oil control solenoid assembly from the timing chain cover assembly.

      Note

      If the camshaft timing oil control solenoid assembly has been struck or dropped, replace it.

    3. Remove the O-ring from the camshaft timing oil control solenoid assembly.

      Note


      • If the O-ring comes off in the timing chain cover assembly, make sure to remove it.

      • Do not drop the O-ring into the timing chain cover assembly.

  10. REMOVE CAMSHAFT TIMING OIL CONTROL SOLENOID ASSEMBLY (for Exhaust Side of Bank 2)


    1. B0073IB

      Remove the bolt and separate the wire harness clamp bracket from the timing chain cover assembly.

    2. B0074LD

      Disconnect the camshaft timing oil control solenoid assembly connector.

    3. Remove the 2 bolts and camshaft timing oil control solenoid assembly from the timing chain cover assembly.

      Note

      If the camshaft timing oil control solenoid assembly has been struck or dropped, replace it.

    4. Remove the O-ring from the camshaft timing oil control solenoid assembly.

      Note


      • If the O-ring comes off in the timing chain cover assembly, make sure to remove it.

      • Do not drop the O-ring into the timing chain cover assembly.