SFI SYSTEM(w/o Canister Pump Module), Diagnostic DTC:P001400, P001500, P002400, P002500

DTC Code DTC Name
P001400 Camshaft Position "B" - Timing Over-Advanced or System Performance Bank 1
P001500 Camshaft Position "B" - Timing Over-Retarded Bank 1
P002400 Camshaft Position "B" - Timing Over-Advanced or System Performance Bank 2
P002500 Camshaft Position "B" - Timing Over-Retarded Bank 2

DESCRIPTION

Refer to DTC P001313.

Click here

DTC No. Detection Item DTC Detection Condition Trouble Area MIL Memory Note
P001400 Camshaft Position "B" - Timing Over-Advanced or System Performance Bank 1 Exhaust valve timing is stuck at a certain value when in the advance range (2 trip detection logic).

  • Valve timing

  • Cam timing oil control solenoid assembly (for exhaust camshaft of bank 1)

  • Camshaft timing gear bolt (camshaft timing oil control valve assembly [for exhaust camshaft of bank 1])

  • Camshaft timing exhaust gear assembly (bank 1)

  • Oil control valve filter (for exhaust camshaft of bank 1)

  • ECM

 Comes on DTC stored SAE Code: P0014
P001500 Camshaft Position "B" - Timing Over-Retarded Bank 1 Exhaust valve timing is stuck at a certain value when in the retard range (1 trip detection logic).

  • Valve timing

  • Cam timing oil control solenoid assembly (for exhaust camshaft of bank 1)

  • Camshaft timing gear bolt (camshaft timing oil control valve assembly [for exhaust camshaft of bank 1])

  • Camshaft timing exhaust gear assembly (bank 1)

  • Oil control valve filter (for exhaust camshaft of bank 1)

  • ECM

 Comes on DTC stored SAE Code: P0015
P002400 Camshaft Position "B" - Timing Over-Advanced or System Performance Bank 2 Exhaust valve timing is stuck at a certain value when in the advance range (2 trip detection logic).

  • Valve timing

  • Cam timing oil control solenoid assembly (for exhaust camshaft of bank 2)

  • Camshaft timing gear bolt (camshaft timing oil control valve assembly [for exhaust camshaft of bank 2])

  • Camshaft timing exhaust gear assembly (bank 2)

  • Oil control valve filter (for exhaust camshaft of bank 2)

  • ECM

 Comes on DTC stored SAE Code: P0024
P002500 Camshaft Position "B" - Timing Over-Retarded Bank 2 Exhaust valve timing is stuck at a certain value when in the retard range (1 trip detection logic).

  • Valve timing

  • Cam timing oil control solenoid assembly (for exhaust camshaft of bank 2)

  • Camshaft timing gear bolt (camshaft timing oil control valve assembly [for exhaust camshaft of bank 2])

  • Camshaft timing exhaust gear assembly (bank 2)

  • Oil control valve filter (for exhaust camshaft of bank 2)

  • ECM

 Comes on DTC stored SAE Code: P0025

MONITOR DESCRIPTION

The ECM optimizes the exhaust valve timing using the Variable Valve Timing (VVT) system to control the exhaust camshaft. The VVT system includes the ECM, cam timing oil control solenoid assembly, camshaft timing gear bolt (camshaft timing oil control valve assembly [for exhaust camshaft]) and camshaft timing exhaust gear assembly. The ECM sends a target duty-cycle control signal to the cam timing oil control solenoid assembly. The camshaft timing gear bolt (camshaft timing oil control valve assembly [for exhaust camshaft]) is operated to control the oil pressure supplied to the camshaft timing exhaust gear assembly based on this signal. The camshaft timing exhaust gear assembly can advance or retard the exhaust camshaft.

If the difference between the target and actual exhaust valve timing is large, and changes in the actual exhaust valve timing are small, the ECM interprets this as the camshaft timing exhaust gear assembly stuck malfunction and stores a DTC.


DTC P001400 and P002400 (Advanced Camshaft Timing) is subject to 2 trip detection logic.

DTC P001500 and P002500 (Retarded Camshaft Timing) is subject to 1 trip detection logic.

These DTCs indicate that the camshaft timing exhaust gear assembly cannot operate properly due to a camshaft timing gear bolt (camshaft timing oil control valve assembly [for exhaust camshaft]) malfunction or the presence of foreign matter in the camshaft timing gear bolt (camshaft timing oil control valve assembly [for exhaust camshaft]).

MONITOR STRATEGY

Required Sensors/Components (Main)

Cam timing oil control solenoid assembly (for exhaust camshaft)

Camshaft timing gear bolt (camshaft timing oil control valve assembly [for exhaust camshaft])

Camshaft timing exhaust gear assembly
Required Sensors/Components (Related)

Crankshaft position sensor

VVT sensor

Engine coolant temperature sensor
Frequency of Operation Continuous

CONFIRMATION DRIVING PATTERN

B0075BME09

  1. Connect the GTS to the DLC3.

  2. Turn the engine switch on (IG).

  3. Turn the GTS on.

  4. Clear the DTCs (even if no DTCs are stored, perform the clear DTC procedure).

  5. Turn the engine switch off and wait for at least 30 seconds.

  6. Turn the engine switch on (IG) [A].

  7. Turn the GTS on.

  8. Start the engine and warm it up until the engine coolant temperature reaches 75°C (167°F) or higher [B].

  9. Drive the vehicle at approximately 60 km/h (37 mph) for 10 minutes or more [C].

    CAUTION:

    When performing the confirmation driving pattern, obey all speed limits and traffic laws.

  10. Idle the engine for 3 minutes or more [D].

  11. Enter the following menus: Powertrain / Engine / Trouble Codes [E].

  12. Read the pending DTCs.

    Tech Tips


    • If a pending DTC is output, the system is malfunctioning.

    • If a pending DTC is not output, perform the following procedure.

  13. Enter the following menus: Powertrain / Engine / Utility / All Readiness.

  14. Input the DTC: P001400, P001500, P002400 or P002500.

  15. Check the DTC judgment result.

    GTS Display Description
    NORMAL

    • DTC judgment completed

    • System normal
    ABNORMAL

    • DTC judgment completed

    • System abnormal
    INCOMPLETE

    • DTC judgment not completed

    • Perform driving pattern after confirming DTC enabling conditions

    Tech Tips


    • If the judgment result is NORMAL, the system is normal.

    • If the judgment result is ABNORMAL, the system has a malfunction.

    • If the judgment result is INCOMPLETE, perform steps [F] through [H].

  16. Repeat the pattern of accelerating the vehicle from rest to approximately 60 km/h (37 mph) and then decelerating the vehicle 10 to 15 times [F].

    CAUTION:

    When performing the confirmation driving pattern, obey all speed limits and traffic laws.

    Tech Tips

    Depress the accelerator pedal by a large amount.

  17. Idle the engine for 3 minutes or more [G].

  18. Enter the following menus: Powertrain / Engine / Trouble Codes [H].

  19. Read the pending DTCs.

    Tech Tips


    • If a pending DTC is output, the system is malfunctioning.

    • If a pending DTC is not output, perform the following procedure.

  20. Check the DTC judgment result again.

    Tech Tips


    • If the judgment result is NORMAL, the system is normal.

    • If the judgment result is ABNORMAL, the system has a malfunction.

WIRING DIAGRAM

Refer to DTC P001313.

Click here

CAUTION / NOTICE / HINT

Tech Tips

Abnormal Bank

Timing Over Advanced

(Valve timing is out of specified range)

Timing Over Retarded

(Valve timing is out of specified range)
Bank 1 P001400 P001500
Bank 2 P002400 P002500

  • If DTC P001400 or P001500 is output, check the VVT system (for exhaust camshaft of bank 1) circuit.

  • If DTC P002400 or P002500 is output, check the VVT system (for exhaust camshaft of bank 2) circuit.

  • Bank 1 refers to the bank that includes the No. 1 cylinder*.

    *: The No. 1 cylinder is the cylinder which is farthest from the transmission.

  • Bank 2 refers to the bank that does not include the No. 1 cylinder.

  • DTC P001400, P001500, P002400 or P002500 may be stored when foreign matter in the engine oil is caught in some parts of the system. The DTC will remain stored even if the system returns to normal after a short time. This foreign matter may then be captured by the oil filter.

  • Read freeze frame data using the GTS. The ECM records vehicle and driving condition information as freeze frame data the moment a DTC is stored. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, if the air fuel ratio was lean or rich, and other data from the time the malfunction occurred.

PROCEDURE


  1. CHECK ANY OTHER DTCS OUTPUT (IN ADDITION TO DTC P001400, P001500, P002400 OR P002500)


    1. Connect the GTS to the DLC3.

    2. Turn the engine switch on (IG).

    3. Turn the GTS on.

    4. Enter the following menus: Powertrain / Engine / Trouble Codes.

    5. Read the DTCs.


      Powertrain > Engine > Trouble Codes
      Result
      Result Proceed to
      DTC P001400, P001500, P002400 or P002500 is output A
      DTC P001400, P001500, P002400 or P002500 and other DTCs are output B

      Tech Tips

      If any DTCs other than P001400, P001500, P002400 or P002500 are output, troubleshoot those DTCs first.


    B

    GO TO DTC CHART Click here

    A

  2. PERFORM ACTIVE TEST USING GTS (CONTROL THE EXHAUST VVT OCV DUTY RATIO)


    1. Connect the GTS to the DLC3.

    2. Start the engine.

    3. Turn the GTS on.

    4. Enter the following menus: Powertrain / Engine / Active Test / Control the Exhaust VVT OCV Duty Ratio Bank 1 or Control the Exhaust VVT OCV Duty Ratio Bank 2.


      Powertrain > Engine > Active Test
      Tester Display
      Control the Exhaust VVT OCV Duty Ratio Bank 1

      Powertrain > Engine > Active Test
      Tester Display
      Control the Exhaust VVT OCV Duty Ratio Bank 2

    5. Check the engine speed while operating the cam timing oil control solenoid assembly (for exhaust camshaft) using the GTS.

      OK
      GTS Operation Engine Condition
      0% Normal engine speed
      100% Engine idles roughly or stalls

      Tech Tips

      Refer to "Data List / Active Test" [Exhaust VVT OCV Control Duty Ratio Bank 1, Exhaust VVT Change Angle Bank 1, Exhaust VVT OCV Control Duty Ratio Bank 2 and Exhaust VVT Change Angle Bank 2].

      Click here

      Result
      Proceed to
      OK
      NG

    NG

    GO TO STEP 5 Click here

    OK

  3. CLEAR DTC


    1. Connect the GTS to the DLC3.

    2. Turn the engine switch on (IG).

    3. Turn the GTS on.

    4. Clear the DTC.


      Powertrain > Engine > Clear DTCs

    5. Turn the engine switch off and wait for at least 30 seconds.

      Result
      Proceed to
      NEXT

    NEXT

  4. CHECK WHETHER DTC OUTPUT RECURS (DTC P001400, P001500, P002400 OR P002500)


    1. Drive the vehicle in accordance with the driving pattern described in Confirmation Driving Pattern.

    2. Enter the following menus: Powertrain / Engine / Trouble Codes.

    3. Read the DTCs.


      Powertrain > Engine > Trouble Codes
      Result
      Result Proceed to
      DTCs are not output A
      DTC P001400, P001500, P002400 or P002500 is output B

      Tech Tips

      DTC P001400, P001500, P002400 or P002500 may be stored when foreign matter in the engine oil is caught in some parts of the system. The DTC will remain stored even if the system returns to normal after a short time. This foreign matter may then be captured by the oil filter.


    A

    CHECK FOR INTERMITTENT PROBLEMS Click here

    B

  5. INSPECT CAM TIMING OIL CONTROL SOLENOID ASSEMBLY (FOR EXHAUST CAMSHAFT)


    1. Inspect the cam timing oil control solenoid assembly (for exhaust camshaft).

      Click here

      Result
      Proceed to
      OK
      NG

    NG

    REPLACE CAM TIMING OIL CONTROL SOLENOID ASSEMBLY (FOR EXHAUST CAMSHAFT) Click here

    OK

  6. INSPECT CAMSHAFT TIMING GEAR BOLT (CAMSHAFT TIMING OIL CONTROL VALVE ASSEMBLY [FOR EXHAUST CAMSHAFT])


    1. Inspect the camshaft timing gear bolt (camshaft timing oil control valve assembly [for exhaust camshaft]).


      Result
      Proceed to
      OK
      NG

    NG

    GO TO STEP 14 Click here

    OK

  7. CHECK VALVE TIMING (CHECK FOR LOOSE TIMING CHAIN AND JUMPED TEETH)


    1. Remove the cylinder head cover sub-assembly and cylinder head cover sub-assembly LH.

      B0076A5C03
      *a Timing Mark *b TDC Timing Mark
      *c Groove - -

    2. Turn the crankshaft pulley and align its groove with the TDC timing mark of the timing chain cover.

    3. Check that the timing marks of the camshaft timing gear assemblies and camshaft timing exhaust gear assemblies are aligned with the timing marks of the bearing cap as shown in the illustration.

      Tech Tips

      If the timing marks are not as shown, turn the crankshaft one revolution clockwise.

      OK
      Timing marks on camshaft timing gear assemblies and camshaft timing exhaust gear assemblies are aligned as shown in the illustration.

      Tech Tips

      If the result is not as specified, check for mechanical malfunctions that may have affected the valve timing, such as a jumped tooth or stretching of the timing chain.

      Result
      Proceed to
      OK
      NG

    NG

    CHECK ENGINE MECHANICAL SYSTEM Click here

    OK

  8. INSPECT OIL CONTROL VALVE FILTER (FOR EXHAUST CAMSHAFT)

    B0073QWC04
    *A for Exhaust Camshaft of Bank 1 *B for Exhaust Camshaft of Bank 2
    *1 Oil Control Value Filter - -

    1. Remove the oil control valve filter (for exhaust camshaft of bank 1) or oil control valve filter (for exhaust camshaft of bank 2).


    2. Check that the filter is not clogged.

      OK
      Filter is not clogged.
      Result
      Proceed to
      OK
      NG

    OK

    GO TO STEP 16 Click here

    NG

    REPLACE OIL CONTROL VALVE FILTER (FOR EXHAUST CAMSHAFT) for Bank 1: Click here for Bank 2: Click here

  9. CHECK ENGINE MECHANICAL SYSTEM


    1. Check for mechanical malfunctions that affect the valve timing, such as a jumped tooth or stretching of the timing chain.

      Tech Tips

      Perform "Inspection After Repair" after repairing or replacing the engine mechanical system.

      Click here

      Result
      Proceed to
      OK
      NG

    NG

    REPAIR OR REPLACE MALFUNCTIONING PARTS, COMPONENT AND AREA

    OK

  10. CLEAR DTC


    1. Connect the GTS to the DLC3.

    2. Turn the engine switch on (IG).

    3. Turn the GTS on.

    4. Clear the DTC.


      Powertrain > Engine > Clear DTCs

    5. Turn the engine switch off and wait for at least 30 seconds.

      Result
      Proceed to
      NEXT

    NEXT

  11. CHECK WHETHER DTC OUTPUT RECURS (DTC P001400, P001500, P002400 OR P002500)


    1. Drive the vehicle in accordance with the driving pattern described in Confirmation Driving Pattern.

    2. Enter the following menus: Powertrain / Engine / Trouble Codes.

    3. Read the DTCs.


      Powertrain > Engine > Trouble Codes
      Result
      Result Proceed to
      DTCs are not output A
      DTC P001400, P001500, P002400 or P002500 is output B

    A

    CHECK FOR INTERMITTENT PROBLEMS Click here

    B

    REPLACE ECM Click here

  12. REPLACE CAM TIMING OIL CONTROL SOLENOID ASSEMBLY (FOR EXHAUST CAMSHAFT)


    1. Replace the cam timing oil control solenoid assembly (for exhaust camshaft).

      Click here

      Result
      Proceed to
      NEXT

    NEXT

  13. INSPECT CAMSHAFT TIMING GEAR BOLT (CAMSHAFT TIMING OIL CONTROL VALVE ASSEMBLY [FOR EXHAUST CAMSHAFT])


    1. Inspect the camshaft timing gear bolt (camshaft timing oil control valve assembly [for exhaust camshaft]).


      Result
      Proceed to
      OK
      NG

    OK

    GO TO STEP 15 Click here

    NG

  14. REPLACE CAMSHAFT TIMING GEAR BOLT (CAMSHAFT TIMING OIL CONTROL VALVE ASSEMBLY [FOR EXHAUST CAMSHAFT])


    1. Replace the camshaft timing gear bolt (camshaft timing oil control valve assembly [for exhaust camshaft]).


      Result
      Proceed to
      NEXT

    NEXT

  15. PERFORM ACTIVE TEST USING GTS (CONTROL THE EXHAUST VVT OCV DUTY RATIO)


    1. Connect the GTS to the DLC3.

    2. Start the engine.

    3. Turn the GTS on.

    4. Enter the following menus: Powertrain / Engine / Active Test / Control the Exhaust VVT OCV Duty Ratio Bank 1 or Control the Exhaust VVT OCV Duty Ratio Bank 2.


      Powertrain > Engine > Active Test
      Tester Display
      Control the Exhaust VVT OCV Duty Ratio Bank 1

      Powertrain > Engine > Active Test
      Tester Display
      Control the Exhaust VVT OCV Duty Ratio Bank 2

    5. Check the engine speed while operating the cam timing oil control solenoid assembly (for exhaust camshaft) using the GTS.

      OK
      GTS Operation Engine Condition
      0% Normal engine speed
      100% Engine idles roughly or stalls

      Tech Tips

      Refer to "Data List / Active Test" [Exhaust VVT OCV Control Duty Ratio Bank 1, Exhaust VVT Change Angle Bank 1, Exhaust VVT OCV Control Duty Ratio Bank 2 and Exhaust VVT Change Angle Bank 2].

      Click here

      Result
      Proceed to
      OK
      NG

    OK

    END

    NG

  16. REPLACE CAMSHAFT TIMING EXHAUST GEAR ASSEMBLY


    1. Replace the camshaft timing exhaust gear assembly.

      Click here

      Tech Tips

      Perform "Inspection After Repair" after replacing the camshaft timing exhaust gear assembly.

      Click here

      Result
      Proceed to
      NEXT

    NEXT

  17. CLEAR DTC


    1. Connect the GTS to the DLC3.

    2. Turn the engine switch on (IG).

    3. Turn the GTS on.

    4. Clear the DTC.


      Powertrain > Engine > Clear DTCs

    5. Turn the engine switch off and wait for at least 30 seconds.

      Result
      Proceed to
      NEXT

    NEXT

  18. CHECK WHETHER DTC OUTPUT RECURS (DTC P001400, P001500, P002400 OR P002500)


    1. Drive the vehicle in accordance with the driving pattern described in Confirmation Driving Pattern.

    2. Enter the following menus: Powertrain / Engine / Trouble Codes.

    3. Read the DTCs.


      Powertrain > Engine > Trouble Codes
      Result
      Result Proceed to
      DTCs are not output A
      DTC P001400, P001500, P002400 or P002500 is output B

    A

    END

    B

    REPLACE ECM Click here