SFI SYSTEM(w/ Canister Pump Module), Diagnostic DTC:P060596, P060796

DTC Code DTC Name
P060596 Control Module Performance Bank 2 Component Internal Failure
P060796 Control Module Performance Bank 1 Component Internal Failure

MONITOR DESCRIPTION

The ECM continuously monitors its internal processors (CPUs) and heated oxygen sensor transistors. This self-check ensures that the ECM is functioning properly.

DTC No. Detection Item DTC Detection Condition Trouble Area MIL Memory Note
P060596 Control Module Performance Bank 2 Component Internal Failure

Either of the following condition is met (1 trip detection logic):


  • The ECM CPUs malfunction.

  • The heated oxygen sensor transistor (built into the ECM) malfunctions.

  • ECM

  • Heated oxygen sensor (bank 2 sensor 2)

  • Exhaust gas leak

 Comes on DTC stored SAE Code: P0607
P060796 Control Module Performance Bank 1 Component Internal Failure

Either of the following condition is met (1 trip detection logic):


  • The ECM CPUs malfunction.

  • The heated oxygen sensor transistor (built into the ECM) malfunctions.

  • ECM

  • Heated oxygen sensor (bank 1 sensor 2)

  • Exhaust gas leak

 Comes on DTC stored SAE Code: P0607

MONITOR STRATEGY

Required Sensors/Components (Main) ECM
Required Sensors/Components (Related) Heated oxygen sensor
Frequency of Operation Continuous

CONFIRMATION DRIVING PATTERN

B00745ZE44

  1. Stop the engine for 30 minutes or more.

  2. Connect the GTS to the DLC3.

  3. Turn the engine switch on (IG).

  4. Turn the GTS on.

  5. Clear the DTCs (even if no DTCs are stored, perform the clear DTC procedure).

  6. Turn the engine switch off and wait for at least 30 seconds.

  7. Turn the engine switch on (IG) [A].

  8. Turn the GTS on.

  9. Start the engine and wait 2 minutes [B].

  10. Warm up the engine until the engine coolant temperature is 75°C (167°F) or higher [C].

  11. Idle the engine for 1 minute [D].

  12. Accelerate the vehicle to 80 km/h (50 mph) and stop the vehicle [E].

    CAUTION:

    When performing the confirmation driving pattern, obey all speed limits and traffic laws.

  13. Drive the vehicle at 60 to 80 km/h (37 to 50 mph) for 5 minutes or more [F].

    CAUTION:

    When performing the confirmation driving pattern, obey all speed limits and traffic laws.

  14. Enter the following menus: Powertrain / Engine / Trouble Codes [G].

  15. Read the pending DTCs.

    Tech Tips


    • If a pending DTC is output, the system is malfunctioning.

    • If a pending DTC is not output, perform the following procedure.

  16. Enter the following menus: Powertrain / Engine / Utility / All Readiness.

  17. Input the DTC: P060596, P060796, P013611, P013613, P013614, P013615, P013617, P015611, P015613, P015614, P015615 or P015617.

  18. Check the DTC judgment result.

    GTS Display Description
    NORMAL

    • DTC judgment completed

    • System normal
    ABNORMAL

    • DTC judgment completed

    • System abnormal
    INCOMPLETE

    • DTC judgment not completed

    • Perform driving pattern after confirming DTC enabling conditions

    Tech Tips


    • If the judgment result is NORMAL, the system is normal.

    • If the judgment result is ABNORMAL, the system is malfunctioning.

    • If the judgment result is INCOMPLETE, perform steps [B] through [F] again.

CAUTION / NOTICE / HINT

Tech Tips

Read freeze frame data using the GTS. The ECM records vehicle and driving condition information as freeze frame data the moment a DTC is stored. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, if the air fuel ratio was lean or rich, and other data from the time the malfunction occurred.

PROCEDURE


  1. CHECK ANY OTHER DTCS OUTPUT (IN ADDITION TO DTC P060596 OR P060796)


    1. Connect the GTS to the DLC3.

    2. Turn the engine switch on (IG).

    3. Turn the GTS on.

    4. Enter the following menus: Powertrain / Engine / Trouble Codes.

    5. Read the DTCs.


      Powertrain > Engine > Trouble Codes
      Result
      Result Proceed to
      DTC P060596 or P060796, and P013611, P013613, P013614, P013615, P013617, P015611, P015613, P015614, P015615 or P015617 are output A
      DTC P060596 or P060796 is output B

    B

    CHECK FOR EXHAUST GAS LEAK Click here

    A

  2. INSPECT DTC (DTC P013611, P013613, P013614, P013615, P013617, P015611, P015613, P015614, P015615 OR P015617)


    1. Refer to the P013611, P013613, P013614, P013615, P013617, P015611, P015613, P015614, P015615 or P015617 flowchart.

      Tech Tips


      • If DTC P013611, P013613, P013614, P013615, P013617, P015611, P015613, P015614, P015615 or P015617 is output, troubleshoot for that DTC first. Then proceed to "Inspect ECM".

        Click here

      • If DTC P060596 or P060796 and P013611, P013613, P013614, P013615, P013617, P015611, P015613, P015614, P015615 or P015617 are output, the output voltage of the heated oxygen sensor may remain close to 0 V or become high (around 1 V or higher).

      Result
      Proceed to
      NEXT

    NEXT

    GO TO STEP 8 Click here

  3. CHECK FOR EXHAUST GAS LEAK


    1. Allow the engine to idle, and then rev the engine.

    2. Check for exhaust gas leaks around the heated oxygen sensor.

      If any exhaust gas leaks are present, repair them and proceed to "Perform Confirmation Driving Pattern". If no exhaust gas leaks are present, proceed to "Perform Confirmation Driving Pattern".

      Tech Tips


      • If no exhaust gas leaks are present, there may be a malfunction in the heated oxygen sensor circuit.

      • If any exhaust gas leaks are present around the heated oxygen sensor, noise appears in the output voltage of the heated oxygen sensor.

      • Perform "Inspection After Repair" after repairing or replacing the exhaust system.

        Click here

      Result
      Proceed to
      NEXT

    NEXT

  4. CLEAR DTC


    1. Connect the GTS to the DLC3.

    2. Turn the engine switch on (IG).

    3. Turn the GTS on.

    4. Clear the DTC.


      Powertrain > Engine > Clear DTCs

    5. Turn the engine switch off and wait for at least 30 seconds.

      Result
      Proceed to
      NEXT

    NEXT

  5. PERFORM CONFIRMATION DRIVING PATTERN

    B0073DZE94

    1. Start the engine.

    2. Warm up the engine until the engine coolant temperature is 75°C (167°F) or higher.

    3. Drive the vehicle in accordance with the driving pattern described in Confirmation Driving Pattern.

      CAUTION:

      When performing the confirmation driving pattern, obey all speed limits and traffic laws.


      1. Accelerate the vehicle to 80 km/h (50 mph) and stop the vehicle.

      2. Drive the vehicle between 60 and 80 km/h (37 and 50 mph) for 5 minutes.

    4. Enter the following menus: Powertrain / Engine / Trouble Codes.

    5. Read the DTCs.


      Powertrain > Engine > Trouble Codes
      Result
      Result Proceed to
      DTC P060596 or P060796, and P013611, P013613, P013614, P013615, P013617, P015611, P015613, P015614, P015615 or P015617 are output A
      Only DTC P060596 or P060796 is output B
      DTCs are not output C

    B

    REPLACE ECM Click here

    C

    GO TO STEP 8 Click here

    A

  6. INSPECT DTC (DTC P013611, P013613, P013614, P013615, P013617, P015611, P015613, P015614, P015615 OR P015617)


    1. Refer to the P013611, P013613, P013614, P013615, P013617, P015611, P015613, P015614, P015615 or P015617 flowchart.

      Tech Tips


      • If DTC P013611, P013613, P013614, P013615, P013617, P015611, P015613, P015614, P015615 or P015617 is output, troubleshoot for that DTC first. Then proceed to "Inspect ECM".

        Click here

      • If DTC P060596 or P060796 and P013611, P013613, P013614, P013615, P013617, P015611, P015613, P015614, P015615 or P015617 are output, the output voltage of the heated oxygen sensor may remain close to 0 V or become high (around 1 V or higher).

      Result
      Proceed to
      NEXT

    NEXT

  7. CLEAR DTC


    1. Connect the GTS to the DLC3.

    2. Turn the engine switch on (IG).

    3. Turn the GTS on.

    4. Clear the DTC.


      Powertrain > Engine > Clear DTCs
      Result
      Proceed to
      NEXT

    NEXT

  8. INSPECT ECM


    1. Stop the engine and wait for 30 minutes.

    2. Start the engine and allow it to idle for 2 minutes.

    3. Turn the GTS on.

    4. Enter the following menus: Powertrain / Engine / Trouble Codes.

    5. Read the DTCs.


      Powertrain > Engine > Trouble Codes
      Result
      Result Proceed to
      DTCs are not output A
      DTC P060596 or P060796 is output B

    A

    END

    B

    REPLACE ECM Click here