SFI SYSTEM(w/ Canister Pump Module), Diagnostic DTC:P033511, P033515

DTC Code DTC Name
P033511 Crankshaft Position Sensor "A" Circuit Short to Ground
P033515 Crankshaft Position Sensor "A" Circuit Short to Battery or Open

DESCRIPTION

The crankshaft position sensor system consists of a No. 1 crankshaft position sensor plate and Magneto Resistance Element (MRE) type sensor. The crankshaft position sensor plate has 34 teeth at 10° intervals (2 teeth are missing for detecting top dead center), and is installed on the crankshaft. The crankshaft position sensor generates 34 signals per crankshaft revolution. The ECM uses the crankshaft position sensor signal (NE signal) to detect the crankshaft position and engine speed.

DTC No. Detection Item DTC Detection Condition Trouble Area MIL Memory Note
P033511 Crankshaft Position Sensor "A" Circuit Short to Ground The crankshaft position sensor output voltage is less than 0.3 V for 4 seconds or more (1 trip detection logic).

  • Open or short in crankshaft position sensor circuit

  • Crankshaft position sensor

  • ECM

 Comes on DTC stored SAE Code: P0337
P033515 Crankshaft Position Sensor "A" Circuit Short to Battery or Open The crankshaft position sensor output voltage is higher than 4.7 V for 4 seconds or more (1 trip detection logic).

  • Open or short in crankshaft position sensor circuit

  • Crankshaft position sensor

  • ECM

 Comes on DTC stored SAE Code: P0338

MONITOR DESCRIPTION

If the output voltage transmitted by the crankshaft position sensor remains low or high, the ECM interprets this as a malfunction in the sensor circuit, illuminates the MIL and stores a DTC.

MONITOR STRATEGY

Required Sensors/Components (Main) Crankshaft position sensor
Required Sensors/Components (Related) VVT sensor
Frequency of Operation Continuous

CONFIRMATION DRIVING PATTERN


  1. Connect the GTS to the DLC3.

  2. Turn the engine switch on (IG).

  3. Turn the GTS on.

  4. Clear the DTCs (even if no DTCs are stored, perform the clear DTC procedure).

  5. Turn the engine switch off and wait for at least 30 seconds.

  6. Turn the engine switch on (IG) [A].

  7. Turn the GTS on.

  8. Wait 5 seconds or more [B].

  9. Enter the following menus: Powertrain / Engine / Trouble Codes [C].

  10. Read the pending DTCs.

    Tech Tips


    • If a pending DTC is output, the system is malfunctioning.

    • If a pending DTC is not output, perform the following procedure.

  11. Enter the following menus: Powertrain / Engine / Utility / All Readiness.

  12. Input the DTC: P033511 or P033515.

  13. Check the DTC judgment result.

    GTS Display Description
    NORMAL

    • DTC judgment completed

    • System normal
    ABNORMAL

    • DTC judgment completed

    • System abnormal
    INCOMPLETE

    • DTC judgment not completed

    • Perform driving pattern after confirming DTC enabling conditions

    Tech Tips


    • If the judgment result is NORMAL, the system is normal.

    • If the judgment result is ABNORMAL, the system has a malfunction.

WIRING DIAGRAM

B0076J0E31
*a 1.5 kΩ
*b Crankshaft Position Sensor

CAUTION / NOTICE / HINT

Tech Tips


  • The engine speed can be checked by using the GTS. To perform the check, follow the procedures below:


    1. Connect the GTS to the DLC3.

    2. Turn the engine switch on (IG).

    3. Turn the GTS on.

    4. Enter the following menus: Powertrain / Engine / Data List / Engine Speed.

    5. Start the engine.


    • The engine speed may be indicated as zero despite the engine running normally. This is caused by a lack of NE signals from the crankshaft position sensor. Alternatively, the engine speed may be indicated as lower than the actual engine speed if the crankshaft position sensor output voltage is insufficient.

  • Read Freeze Frame Data using the GTS. The ECM records vehicle and driving condition information as Freeze Frame Data the moment a DTC is stored. When troubleshooting, Freeze Frame Data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, if the air fuel ratio was lean or rich, and other data from the time the malfunction occurred.

PROCEDURE


  1. READ VALUE USING GTS (ENGINE SPEED)


    1. Connect the GTS to the DLC3.

    2. Turn the engine switch on (IG).

    3. Turn the GTS on.

    4. Enter the following menus: Powertrain / Engine / Data List / Engine Speed.


      Powertrain > Engine > Data List
      Tester Display
      Engine Speed

    5. Start the engine.

    6. Read the values displayed on the GTS while the engine is running.

      Standard
      Correct values are displayed.

      Tech Tips


      • To check the engine speed change, display the graph on the GTS.

      • If the engine does not start, check the engine speed while cranking.

      • If the engine speed indicated on the GTS remains at zero (0), there may be an open or short in the crankshaft position sensor circuit.

      Result
      Proceed to
      OK
      NG

    OK

    CHECK FOR INTERMITTENT PROBLEMS Click here

    NG

  2. CHECK HARNESS AND CONNECTOR

    B0075FIC01
    *a

    Front view of wire harness connector

    (to Crankshaft Position Sensor)

    Tech Tips

    Make sure that the connector is properly connected. If it is not, securely connect it and check for DTCs again.


    1. Disconnect the crankshaft position sensor connector.

    2. Turn the engine switch on (IG).

    3. Measure the voltage according to the value(s) in the table below.

      Standard Voltage
      Tester Connection Condition Specified Condition
      F72-1 (VC) - Body ground Engine switch on (IG) 4.5 to 5.5 V
      F72-3 (NE+) - Body ground Engine switch on (IG) 3.0 to 5.0 V

    4. Turn the engine switch off and wait for at least 30 seconds.

    5. Measure the resistance according to the value(s) in the table below.

      Standard Resistance
      Tester Connection Condition Specified Condition
      F72-1 (VC) - F72-3 (NE+) Engine switch off 1.425 to 1.575 kΩ
      F72-2 (NE-) - Body ground Always Below 1 Ω
      Result
      Proceed to
      OK
      NG

    OK

    REPLACE CRANKSHAFT POSITION SENSOR Click here

    NG

  3. CHECK HARNESS AND CONNECTOR (CRANKSHAFT POSITION SENSOR - ECM)


    1. Disconnect the crankshaft position sensor connector.

    2. Disconnect the ECM connector.

    3. Measure the resistance according to the value(s) in the table below.

      Standard Resistance
      Tester Connection Condition Specified Condition
      F72-1 (VC) - F87-96 (VCNE) Always Below 1 Ω
      F72-2 (NE-) - F87-95 (NE-) Always Below 1 Ω
      F72-3 (NE+) - F87-128 (NE+) Always Below 1 Ω
      F72-1 (VC) or F87-96 (VCNE) - Body ground and other terminals Always 10 kΩ or higher
      F72-2 (NE-) or F87-95 (NE-) - Body ground and other terminals Always 10 kΩ or higher
      F72-3 (NE+) or F87-128 (NE+) - Body ground and other terminals Always 10 kΩ or higher
      Result
      Proceed to
      OK
      NG

    OK

    REPLACE ECM Click here

    NG

    REPAIR OR REPLACE HARNESS OR CONNECTOR