SFI SYSTEM(w/o Canister Pump Module) Starter Signal Circuit

DESCRIPTION



WIRING DIAGRAM

B0077Z7E02
B0076Y9E02

CAUTION / NOTICE / HINT

Note


  • Inspect the fuses for circuits related to this system before performing the following procedure.

  • After turning engine switch off, waiting time may be required before disconnecting the cable from the negative (-) battery terminal. Therefore, make sure to read the disconnecting the cable from the negative (-) battery terminal notices before proceeding with work.

    Click here

PROCEDURE


  1. CHECK WHETHER ENGINE CAN BE CRANKED


    1. Check if the engine can be cranked.

      Result
      Result Proceed to
      Engine cannot be cranked A
      Engine can be cranked (w/ Stop and Start System) B
      Engine can be cranked (w/o Stop and Start System) C

    B

    READ VALUE USING GTS (STARTER SW) Click here

    C

    READ VALUE USING GTS (STARTER SW) Click here

    A

  2. READ VALUE USING GTS (STARTER SW)


    1. Connect the GTS to the DLC3.

    2. Turn the engine switch on (IG).

    3. Turn the GTS on.

    4. Enter the following menus: Powertrain / Engine / Data List / Starter SW.


      Powertrain > Engine > Data List
      Tester Display
      Starter SW

    5. Check the value displayed on the GTS when the engine switch is turned on (IG) and the engine is cranked.

      OK
      Condition GTS Display (Starter SW)
      Engine switch on (IG) OFF
      Cranking position ON
      Result
      Result Proceed to
      OK (w/ Stop and Start System) A
      OK (w/o Stop and Start System) B
      NG (w/ Stop and Start System) C
      NG (w/o Stop and Start System) D

    B

    INSPECT RELAY (ST NO. 1 RELAY) Click here

    C

    CHECK STOP AND START SYSTEM Click here

    D

    INSPECT PARK/NEUTRAL POSITION SWITCH ASSEMBLY Click here

    A

  3. INSPECT RELAY (ST NO. 2 RELAY)


    1. Inspect the ST NO. 2 relay.

      Click here

      Result
      Proceed to
      OK
      NG

    NG

    REPLACE RELAY (ST NO. 2 RELAY)

    OK

  4. INSPECT RELAY (ST NO. 1 RELAY)


    1. Inspect the ST NO. 1 relay.

      Click here

      Result
      Proceed to
      OK
      NG

    NG

    REPLACE RELAY (ST NO. 1 RELAY)

    OK

  5. INSPECT STARTER ASSEMBLY


    1. Inspect the starter assembly.

      Click here

      Result
      Proceed to
      OK
      NG

    NG

    REPLACE STARTER ASSEMBLY Click here

    OK

  6. CHECK HARNESS AND CONNECTOR (ST NO. 2 RELAY - STARTER ASSEMBLY)


    1. Remove the ST NO. 2 relay from the No. 2 engine room relay block and No. 2 junction block assembly.

    2. Disconnect the starter assembly connector.

    3. Measure the resistance according to the value(s) in the table below.

      Standard Resistance
      Tester Connection Condition Specified Condition
      3 (ST NO. 2 relay) - F86-1 (SL2) Always Below 1 Ω
      3 (ST NO. 2 relay) or F86-1 (SL2) - Body ground and other terminals Always 10 kΩ or higher
      Result
      Proceed to
      OK
      NG

    NG

    REPAIR OR REPLACE HARNESS OR CONNECTOR

    OK

  7. CHECK HARNESS AND CONNECTOR (ST NO. 2 RELAY - ECM)


    1. Remove the ST NO. 2 relay from the No. 2 engine room relay block and No. 2 junction block assembly.

    2. Disconnect the ECM connector.

    3. Disconnect the engine stop and start ECM connector.

    4. Measure the resistance according to the value(s) in the table below.

      Standard Resistance
      Tester Connection Condition Specified Condition
      2 (ST NO. 2 relay) - A91-29 (STA) Always Below 1 Ω
      Result
      Proceed to
      OK
      NG

    NG

    REPAIR OR REPLACE HARNESS OR CONNECTOR

    OK

  8. CHECK HARNESS AND CONNECTOR (ST NO. 2 RELAY - BODY GROUND)


    1. Remove the ST NO. 2 relay from the No. 2 engine room relay block and No. 2 junction block assembly.

    2. Measure the resistance according to the value(s) in the table below.

      Standard Resistance
      Tester Connection Condition Specified Condition
      1 (ST NO. 2 relay) - Body ground Always Below 1 Ω
      Result
      Proceed to
      OK
      NG

    NG

    REPAIR OR REPLACE HARNESS OR CONNECTOR

    OK

  9. CHECK HARNESS AND CONNECTOR (BATTERY - ST NO. 2 RELAY)


    1. Remove the ST NO. 2 relay from the No. 2 engine room relay block and No. 2 junction block assembly.

    2. Measure the voltage according to the value(s) in the table below.

      Standard Voltage
      Tester Connection Condition Specified Condition
      5 (ST NO. 2 relay) - Body ground Always 11 to 14 V
      Result
      Proceed to
      OK
      NG

    NG

    REPAIR OR REPLACE HARNESS OR CONNECTOR

    OK

  10. CHECK HARNESS AND CONNECTOR (BATTERY - ST NO. 1 RELAY)


    1. Remove the ST NO. 1 relay from the No. 2 engine room relay block and No. 2 junction block assembly.

    2. Measure the voltage according to the value(s) in the table below.

      Standard Voltage
      Tester Connection Condition Specified Condition
      5 (ST NO. 1 relay) - Body ground Always 11 to 14 V
      Result
      Proceed to
      OK
      NG

    NG

    REPAIR OR REPLACE HARNESS OR CONNECTOR

    OK

  11. CHECK HARNESS AND CONNECTOR (ST NO. 1 RELAY - STARTER ASSEMBLY)


    1. Remove the ST NO. 1 relay from the No. 2 engine room relay block and No. 2 junction block assembly.

    2. Disconnect the starter assembly connector.

    3. Measure the resistance according to the value(s) in the table below.

      Standard Resistance
      Tester Connection Condition Specified Condition
      3 (ST NO. 1 relay) - F86-2 (SL1) Always Below 1 Ω
      3 (ST NO. 1 relay) or F86-2 (SL1) - Body ground and other terminals Always 10 kΩ or higher
      Result
      Proceed to
      OK
      NG

    NG

    REPAIR OR REPLACE HARNESS OR CONNECTOR

    OK

  12. CHECK HARNESS AND CONNECTOR (ST NO. 1 RELAY - BODY GROUND)


    1. Remove the ST NO. 1 relay from the No. 2 engine room relay block and No. 2 junction block assembly.

    2. Measure the resistance according to the value(s) in the table below.

      Standard Resistance
      Tester Connection Condition Specified Condition
      1 (ST NO. 1 relay) - Body ground Always Below 1 Ω
      Result
      Proceed to
      OK
      NG

    OK

    REPAIR OR REPLACE HARNESS OR CONNECTOR (BATTERY - STARTER ASSEMBLY)

    NG

    REPAIR OR REPLACE HARNESS OR CONNECTOR

  13. INSPECT RELAY (ST NO. 1 RELAY)


    1. Inspect the ST NO. 1 relay.

      Click here

      Result
      Proceed to
      OK
      NG

    NG

    REPLACE RELAY (ST NO. 1 RELAY)

    OK

  14. INSPECT STARTER ASSEMBLY


    1. Inspect the starter assembly.

      Click here

      Result
      Proceed to
      OK
      NG

    NG

    REPLACE STARTER ASSEMBLY Click here

    OK

  15. CHECK HARNESS AND CONNECTOR (ST NO. 1 RELAY - STARTER ASSEMBLY)


    1. Remove the ST NO. 1 relay from the No. 2 engine room relay block and No. 2 junction block assembly.

    2. Disconnect the starter assembly connector.

    3. Measure the resistance according to the value(s) in the table below.

      Standard Resistance
      Tester Connection Condition Specified Condition
      3 (ST NO. 1 relay) - F18-1 (ST) Always Below 1 Ω
      3 (ST NO. 1 relay) or F18-1 (ST) - Body ground and other terminals Always 10 kΩ or higher
      Result
      Proceed to
      OK
      NG

    NG

    REPAIR OR REPLACE HARNESS OR CONNECTOR

    OK

  16. CHECK HARNESS AND CONNECTOR (ST NO. 1 RELAY - BODY GROUND)


    1. Remove the ST NO. 1 relay from the No. 2 engine room relay block and No. 2 junction block assembly.

    2. Measure the resistance according to the value(s) in the table below.

      Standard Resistance
      Tester Connection Condition Specified Condition
      1 (ST NO. 1 relay) - Body ground Always Below 1 Ω
      Result
      Proceed to
      OK
      NG

    NG

    REPAIR OR REPLACE HARNESS OR CONNECTOR

    OK

  17. CHECK HARNESS AND CONNECTOR (PARK/NEUTRAL POSITION SWITCH ASSEMBLY - CERTIFICATION ECU (SMART KEY ECU ASSEMBLY) - ST NO. 1 RELAY)


    1. Disconnect the park/neutral position switch assembly connector.

    2. Disconnect the certification ECU (smart key ECU assembly) connector.

    3. Remove the ST NO. 1 relay from the No. 2 engine room relay block and No. 2 junction block assembly.

    4. Measure the resistance according to the value(s) in the table below.

      Standard Resistance
      Tester Connection Condition Specified Condition
      F80-5 (L) - 2 (ST NO. 1 relay) Always Below 1 Ω
      A13-12 (STA) - 2 (ST NO. 1 relay) Always Below 1 Ω
      Result
      Proceed to
      OK
      NG

    NG

    REPAIR OR REPLACE HARNESS OR CONNECTOR

    OK

  18. CHECK HARNESS AND CONNECTOR (BATTERY - ST NO. 1 RELAY)


    1. Remove the ST NO. 1 relay from the No. 2 engine room relay block and No. 2 junction block assembly.

    2. Measure the voltage according to the value(s) in the table below.

      Standard Voltage
      Tester Connection Condition Specified Condition
      5 (ST NO. 1 relay) - Body ground Always 11 to 14 V
      Result
      Proceed to
      OK
      NG

    OK

    REPAIR OR REPLACE HARNESS OR CONNECTOR (BATTERY - STARTER ASSEMBLY)

    NG

    REPAIR OR REPLACE HARNESS OR CONNECTOR

  19. CHECK STOP AND START SYSTEM


    1. Check the stop and start system.

      Click here

      Result
      Proceed to
      OK
      NG

    OK

    CHECK ENTRY AND START SYSTEM Click here

    NG

    REPAIR OR REPLACE STOP AND START SYSTEM

  20. INSPECT PARK/NEUTRAL POSITION SWITCH ASSEMBLY


    1. Inspect the park/neutral position switch assembly.

      Click here

      Result
      Proceed to
      OK
      NG

    NG

    REPLACE PARK/NEUTRAL POSITION SWITCH ASSEMBLY Click here

    OK

  21. CHECK HARNESS AND CONNECTOR (PARK/NEUTRAL POSITION SWITCH ASSEMBLY - ECM - ST NO. 1 RELAY - CERTIFICATION ECU (SMART KEY ECU ASSEMBLY))


    1. Disconnect the park/neutral position switch assembly connector.

    2. Disconnect the ECM connector.

    3. Remove the ST NO. 1 relay from the No. 2 engine room relay block and No. 2 junction block assembly.

    4. Disconnect the certification ECU (smart key ECU assembly) connector.

    5. Measure the resistance according to the value(s) in the table below.

      Standard Resistance
      Tester Connection Condition Specified Condition
      F80-5 (L) - A91-29 (STA) Always Below 1 Ω
      F80-5 (L), A91-29 (STA),2 (ST NO. 1 relay) or A13-12 (STA) - Body ground and other terminals Always 10 kΩ or higher
      Result
      Proceed to
      OK
      NG

    NG

    REPAIR OR REPLACE HARNESS OR CONNECTOR

    OK

  22. CHECK HARNESS AND CONNECTOR (CERTIFICATION ECU (SMART KEY ECU ASSEMBLY) - PARK/NEUTRAL POSITION SWITCH ASSEMBLY - ECM)


    1. Disconnect the certification ECU (smart key ECU assembly) connector.

    2. Disconnect the park/neutral position switch assembly connector.

    3. Disconnect the ECM connector.

    4. Measure the resistance according to the value(s) in the table below.

      Standard Resistance
      Tester Connection Condition Specified Condition
      A13-10 (STAR) - F80-4 (B) Always Below 1 Ω
      A13-10 (STAR) - A91-57 (NSW) Always Below 1 Ω
      A13-10 (STAR), F80-4 (B) or A91-57 (NSW) - Body ground and other terminals Always 10 kΩ or higher
      Result
      Proceed to
      OK
      NG

    OK

    CHECK ENTRY AND START SYSTEM Click here

    NG

    REPAIR OR REPLACE HARNESS OR CONNECTOR

  23. READ VALUE USING GTS (STARTER SW)


    1. Connect the GTS to the DLC3.

    2. Turn the engine switch on (IG).

    3. Turn the GTS on.

    4. Enter the following menus: Powertrain / Engine / Data List / Starter SW.


      Powertrain > Engine > Data List
      Tester Display
      Starter SW

    5. Check the value displayed on the GTS when the engine switch is turned on (IG) and the engine is cranked.

      OK
      Condition GTS Display (Starter SW)
      Engine switch on (IG) OFF
      Cranking position ON
      Result
      Proceed to
      OK
      NG

    OK

    PROCEED TO NEXT SUSPECTED AREA SHOWN IN PROBLEM SYMPTOMS TABLE Click here

    NG

    REPAIR OR REPLACE HARNESS OR CONNECTOR (ST NO. 2 RELAY - ECM)

  24. READ VALUE USING GTS (STARTER SW)


    1. Connect the GTS to the DLC3.

    2. Turn the engine switch on (IG).

    3. Turn the GTS on.

    4. Enter the following menus: Powertrain / Engine / Data List / Starter SW.


      Powertrain > Engine > Data List
      Tester Display
      Starter SW

    5. Check the value displayed on the GTS when the engine switch is turned on (IG) and the engine is cranked.

      OK
      Condition GTS Display (Starter SW)
      Engine switch on (IG) OFF
      Cranking position ON
      Result
      Proceed to
      OK
      NG

    OK

    PROCEED TO NEXT SUSPECTED AREA SHOWN IN PROBLEM SYMPTOMS TABLE Click here

    NG

    REPAIR OR REPLACE HARNESS OR CONNECTOR (ST NO. 1 RELAY - ECM)