SFI SYSTEM(w/o Canister Pump Module), Diagnostic DTC:P003312

DTC Code DTC Name
P003312 Turbocharger / Supercharger Bypass Valve "A" Control Circuit Short to Battery

DESCRIPTION

The air by-pass valve assembly is installed to the turbocharger compressor housing. It opens and closes in response to drive commands from the ECM. If the air by-pass valve assembly closes during normal boosting and the throttle valve closes while boost pressure is being applied, the air by-pass valve assembly will open and the excess pressure between the turbocharger and the throttle valve will be released.

DTC No. Detection Item DTC Detection Condition Trouble Area MIL Memory Note
P003312 Turbocharger / Supercharger Bypass Valve "A" Control Circuit Short to Battery Short to +B in air by-pass valve assembly circuit (1 trip detection logic).
  • Short in air by-pass valve assembly circuit

  • Air by-pass valve assembly

  • ECM

Does not come on DTC stored SAE Code: P0035

MONITOR DESCRIPTION

The ECM monitors the output voltage while the air by-pass valve assembly is operating.

The air by-pass valve assembly turns on and off according to switching of a transistor inside the ECM.

If a continuous mismatch occurs between the ECM transistor state and the output voltage, the ECM determines there is a malfunction in the air by-pass valve assembly circuit and stores this DTC.

CONFIRMATION DRIVING PATTERN

B007536E11

  1. Connect the GTS to the DLC3.

  2. Turn the engine switch on (IG) and turn the GTS on.

  3. Clear the DTCs (even if no DTCs are stored, perform the clear DTC procedure).

  4. Turn the engine switch off and wait for at least 30 seconds.

  5. Turn the engine switch on (IG) and turn the GTS on.

  6. Start the engine and warm it up until the engine coolant temperature reaches 75°C (167°F) or higher [A].

  7. Accelerate to 50 km/h (31 mph) or more with the accelerator pedal fully depressed [B].

    CAUTION:

    When performing the confirmation driving pattern, obey all speed limits and traffic laws.

  8. Quickly release the accelerator pedal from the fully depressed position [C].

  9. Enter the following menus: Powertrain / Engine / Trouble Codes [D].

  10. Read the pending DTCs.

    Tech Tips


    • If a pending DTC is output, the system is malfunctioning.

    • If a pending DTC is not output, perform the following procedure.

  11. Enter the following menus: Powertrain / Engine / Utility / All Readiness.

  12. Input the DTC: P003312.

  13. Check the DTC judgment result.

    GTS Display Description
    NORMAL
    • DTC judgment completed

    • System normal

    ABNORMAL
    • DTC judgment completed

    • System abnormal

    INCOMPLETE
    • DTC judgment not completed

    • Perform driving pattern after confirming DTC enabling conditions

    N/A
    • Unable to perform DTC judgment

    • Number of DTCs which do not fulfill DTC preconditions has reached ECU memory limit

    Tech Tips


    • If the judgment result shows NORMAL, the system is normal.

    • If the judgment result shows ABNORMAL, the system has a malfunction.

    • If the judgment result shows INCOMPLETE or N/A, perform steps [B] through [D] again.

WIRING DIAGRAM

B0077GFE08

CAUTION / NOTICE / HINT

Note

Inspect the fuses for circuits related to this system before performing the following procedure.

Tech Tips

Read freeze frame data using the GTS. The ECM records vehicle and driving condition information as freeze frame data the moment a DTC is stored. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, if the air fuel ratio was lean or rich, and other data from the time the malfunction occurred.

PROCEDURE


  1. INSPECT AIR BY-PASS VALVE ASSEMBLY


    1. Inspect the air by-pass valve assembly.

      Click here

      Result
      Proceed to
      OK
      NG

    NG
    OK
  2. CHECK HARNESS AND CONNECTOR (AIR BY-PASS VALVE ASSEMBLY - ECM)


    1. Disconnect the air by-pass valve assembly connector.

    2. Disconnect the ECM connector.

    3. Measure the resistance according to the value(s) in the table below.

      Standard Resistance
      Tester Connection Condition Specified Condition
      M4-2 or F66-67 (ABV) - Other terminals Always 10 kΩ or higher
      Result
      Proceed to
      OK
      NG

    NG
    OK
  3. CHECK WHETHER DTC OUTPUT RECURS (DTC P003312)


    1. Connect the GTS to the DLC3.

    2. Turn the engine switch on (IG).

    3. Turn the GTS on.

    4. Clear the DTCs.


      Powertrain > Engine > Clear DTCs
    5. Turn the engine switch off and wait for at least 30 seconds.

    6. Turn the engine switch on (IG).

    7. Turn the GTS on.

    8. Start the engine and warm it up.

    9. Drive the vehicle in accordance with the driving pattern described in Confirmation Driving Pattern.

    10. Enter the following menus: Powertrain / Engine / Utility / All Readiness.


      Powertrain > Engine > Utility
      Tester Display
      All Readiness
    11. Input the DTC: P003312.

    12. Check the DTC judgment result.

      Result
      Result Proceed to

      NORMAL

      (DTCs are not output)

      A

      ABNORMAL

      (DTC P003312 is output)

      B

    A
    B