AUDIO AND VISUAL SYSTEM(w/ Remote Touch) Speaker Circuit

DESCRIPTION

If there is a short in a speaker circuit, the stereo component amplifier assembly detects it and stops output to the speakers.

Thus sound cannot be heard from the speakers even if there is no malfunction in the stereo component amplifier assembly or speakers.

WIRING DIAGRAM


  1. for 10 Speakers

    B0074LBE06
    B0077O7E11

  2. for 17 Speakers

    B0077WTE04
    B0073JHE04

PROCEDURE


  1. CHECK MODEL


    1. Choose the model to be inspected.

      Result
      Result Proceed to
      for 10 Speakers A
      for 17 Speakers B

    B

    CHECK SPEAKER (OPERATION CHECK) Click here

    A

  2. CHECK SPEAKER (OPERATION CHECK)


    1. A01VRF7

      Enter the "System Check Mode" screen. Refer to Check Speaker in Operation Check.

      Click here

    2. Perform the operation check above and determine the speaker that is not operating.

      Result
      Not Operating Speaker Proceed to
      Front No. 2 speaker assembly A
      Front No. 1 speaker assembly B
      Rear speaker assembly C
      Rear No. 3 speaker assembly D
      Front No. 3 speaker assembly E

      Tech Tips

      If sound cannot be heard from any speaker, inspect all of them.


    B

    CHECK HARNESS AND CONNECTOR (STEREO COMPONENT AMPLIFIER ASSEMBLY - FRONT NO. 1 SPEAKER ASSEMBLY) Click here

    C

    CHECK HARNESS AND CONNECTOR (STEREO COMPONENT AMPLIFIER ASSEMBLY - REAR SPEAKER ASSEMBLY) Click here

    D

    CHECK HARNESS AND CONNECTOR (STEREO COMPONENT AMPLIFIER ASSEMBLY - REAR NO. 3 SPEAKER ASSEMBLY) Click here

    E

    CHECK HARNESS AND CONNECTOR (STEREO COMPONENT AMPLIFIER ASSEMBLY - FRONT NO. 3 SPEAKER ASSEMBLY) Click here

    A

  3. CHECK HARNESS AND CONNECTOR (STEREO COMPONENT AMPLIFIER ASSEMBLY - FRONT NO. 2 SPEAKER ASSEMBLY)


    1. Disconnect the T20 stereo component amplifier assembly connector.

    2. Disconnect the O54 and O55 front No. 2 speaker assembly connectors.

    3. Measure the resistance according to the value(s) in the table below.

      Standard Resistance
      Tester Connection Condition Specified Condition
      T20-13 (FR+) - O54-2 (+) Always Below 1 Ω
      T20-28 (FR-) - O54-1 (-) Always Below 1 Ω
      T20-12 (FL+) - O55-2 (+) Always Below 1 Ω
      T20-27 (FL-) - O55-1 (-) Always Below 1 Ω
      T20-13 (FR+) or O54-2 (+) - Body ground Always 10 kΩ or higher
      T20-28 (FR-) or O54-1 (-) - Body ground Always 10 kΩ or higher
      T20-12 (FL+) or O55-2 (+) - Body ground Always 10 kΩ or higher
      T20-27 (FL-) or O55-1 (-) - Body ground Always 10 kΩ or higher
      Result
      Proceed to
      OK
      NG

    NG

    REPAIR OR REPLACE HARNESS OR CONNECTOR

    OK

  4. REPLACE FRONT NO. 2 SPEAKER ASSEMBLY


    1. Remove the front No. 2 speaker assembly.

      Click here

    2. Inspect the front No. 2 speaker assembly.

      Click here

      OK
      Malfunction disappears.
      Result
      Proceed to
      OK
      NG

    OK

    END

    NG

    PROCEED TO NEXT SUSPECTED AREA SHOWN IN PROBLEM SYMPTOMS TABLE Click here

  5. CHECK HARNESS AND CONNECTOR (STEREO COMPONENT AMPLIFIER ASSEMBLY - FRONT NO. 1 SPEAKER ASSEMBLY)


    1. Disconnect the T20 stereo component amplifier assembly connector.

    2. Disconnect the R14 and S14 front No. 1 speaker assembly connectors.

    3. Measure the resistance according to the value(s) in the table below.

      Standard Resistance
      Tester Connection Condition Specified Condition
      T20-5 (WFR+) - R14-1 Always Below 1 Ω
      T20-20 (WFR-) - R14-2 Always Below 1 Ω
      T20-4 (WFL+) - S14-1 Always Below 1 Ω
      T20-19 (WFL-) - S14-2 Always Below 1 Ω
      T20-5 (WFR+) or R14-1 - Body ground Always 10 kΩ or higher
      T20-20 (WFR-) or R14-2 - Body ground Always 10 kΩ or higher
      T20-4 (WFL+) or S14-1 - Body ground Always 10 kΩ or higher
      T20-19 (WFL-) or S14-2 - Body ground Always 10 kΩ or higher
      Result
      Proceed to
      OK
      NG

    NG

    REPAIR OR REPLACE HARNESS OR CONNECTOR

    OK

  6. INSPECT FRONT NO. 1 SPEAKER ASSEMBLY


    1. Remove the front No. 1 speaker assembly.

      Click here

    2. Inspect the front No. 1 speaker assembly.

      Click here

      Result
      Proceed to
      OK
      NG

    OK

    PROCEED TO NEXT SUSPECTED AREA SHOWN IN PROBLEM SYMPTOMS TABLE Click here

    NG

    REPLACE FRONT NO. 1 SPEAKER ASSEMBLY Click here

  7. CHECK HARNESS AND CONNECTOR (STEREO COMPONENT AMPLIFIER ASSEMBLY - REAR SPEAKER ASSEMBLY)


    1. Disconnect the T20 stereo component amplifier assembly connector.

    2. Disconnect the T25 and U35 rear speaker assembly connectors.

    3. Measure the resistance according to the value(s) in the table below.

      Standard Resistance
      Tester Connection Condition Specified Condition
      T20-15 (RR+) - T25-1 Always Below 1 Ω
      T20-30 (RR-) - T25-2 Always Below 1 Ω
      T20-14 (RL+) - U35-1 Always Below 1 Ω
      T20-29 (RL-) - U35-2 Always Below 1 Ω
      T20-15 (RR+) or T25-1 - Body ground Always 10 kΩ or higher
      T20-30 (RR-) or T25-2 - Body ground Always 10 kΩ or higher
      T20-14 (RL+) or U35-1 - Body ground Always 10 kΩ or higher
      T20-29 (RL-) or U35-2 - Body ground Always 10 kΩ or higher
      Result
      Proceed to
      OK
      NG

    NG

    REPAIR OR REPLACE HARNESS OR CONNECTOR

    OK

  8. INSPECT REAR SPEAKER ASSEMBLY


    1. Remove the rear speaker assembly.

      Click here

    2. Inspect the rear speaker assembly.

      Click here

      Result
      Proceed to
      OK
      NG

    OK

    PROCEED TO NEXT SUSPECTED AREA SHOWN IN PROBLEM SYMPTOMS TABLE Click here

    NG

    REPLACE REAR SPEAKER ASSEMBLY Click here

  9. CHECK HARNESS AND CONNECTOR (STEREO COMPONENT AMPLIFIER ASSEMBLY - REAR NO. 3 SPEAKER ASSEMBLY)


    1. Disconnect the T20 stereo component amplifier assembly connector.

    2. Disconnect the T24 rear No. 3 speaker assembly connector.

    3. Measure the resistance according to the value(s) in the table below.

      Standard Resistance
      Tester Connection Condition Specified Condition
      T20-6 (WF1+) - T24-1 Always Below 1 Ω
      T20-21 (WF1-) - T24-2 Always Below 1 Ω
      T20-6 (WF1+) or T24-1 - Body ground Always 10 kΩ or higher
      T20-21 (WF1-) or T24-2 - Body ground Always 10 kΩ or higher
      Result
      Proceed to
      OK
      NG

    NG

    REPAIR OR REPLACE HARNESS OR CONNECTOR

    OK

  10. INSPECT REAR NO. 3 SPEAKER ASSEMBLY


    1. Remove the rear No. 3 speaker assembly.

      Click here

    2. Inspect the rear No. 3 speaker assembly.

      Click here

      Result
      Proceed to
      OK
      NG

    OK

    PROCEED TO NEXT SUSPECTED AREA SHOWN IN PROBLEM SYMPTOMS TABLE Click here

    NG

    REPLACE REAR NO. 3 SPEAKER ASSEMBLY Click here

  11. CHECK HARNESS AND CONNECTOR (STEREO COMPONENT AMPLIFIER ASSEMBLY - FRONT NO. 3 SPEAKER ASSEMBLY)


    1. Disconnect the T20 stereo component amplifier assembly connector.

    2. Disconnect the O56 front No. 3 speaker assembly connector.

    3. Measure the resistance according to the value(s) in the table below.

      Standard Resistance
      Tester Connection Condition Specified Condition
      T20-7 (CTR+) - O56-2 (+) Always Below 1 Ω
      T20-22 (CTR-) - O56-1 (-) Always Below 1 Ω
      T20-7 (CTR+) or O56-2 (+) - Body ground Always 10 kΩ or higher
      T20-22 (CTR-) or O56-1 (-) - Body ground Always 10 kΩ or higher
      Result
      Proceed to
      OK
      NG

    NG

    REPAIR OR REPLACE HARNESS OR CONNECTOR

    OK

  12. INSPECT FRONT NO. 3 SPEAKER ASSEMBLY


    1. Remove the front No. 3 speaker assembly.

      Click here

    2. Inspect the front No. 3 speaker assembly.

      Click here

      Result
      Proceed to
      OK
      NG

    OK

    PROCEED TO NEXT SUSPECTED AREA SHOWN IN PROBLEM SYMPTOMS TABLE Click here

    NG

    REPLACE FRONT NO. 3 SPEAKER ASSEMBLY Click here

  13. CHECK SPEAKER (OPERATION CHECK)


    1. A01VRF7

      Enter the "System Check Mode" screen. Refer to Check Speaker in Operation Check.

      Click here

    2. Perform the operation check above and determine the speaker that is not operating.

      Result
      Not Operating Speaker Proceed to
      Front No. 2 speaker assembly A
      Front No. 1 speaker assembly B
      Front No. 3 speaker assembly C
      Rear speaker assembly or rear No. 2 speaker assembly D
      Rear header speaker assembly E
      Rear No. 3 speaker assembly F

      Tech Tips

      If sound cannot be heard from any speaker, inspect all of them.


    B

    CHECK HARNESS AND CONNECTOR (STEREO COMPONENT AMPLIFIER ASSEMBLY - FRONT NO. 1 SPEAKER ASSEMBLY) Click here

    C

    CHECK HARNESS AND CONNECTOR (STEREO COMPONENT AMPLIFIER ASSEMBLY - FRONT NO. 3 SPEAKER ASSEMBLY) Click here

    D

    CHECK HARNESS AND CONNECTOR (STEREO COMPONENT AMPLIFIER ASSEMBLY - REAR NO. 2 SPEAKER ASSEMBLY) Click here

    E

    CHECK HARNESS AND CONNECTOR (STEREO COMPONENT AMPLIFIER ASSEMBLY - REAR HEADER SPEAKER ASSEMBLY) Click here

    F

    CHECK HARNESS AND CONNECTOR (STEREO COMPONENT AMPLIFIER ASSEMBLY - REAR NO. 3 SPEAKER ASSEMBLY) Click here

    A

  14. CHECK HARNESS AND CONNECTOR (STEREO COMPONENT AMPLIFIER ASSEMBLY - FRONT NO. 2 SPEAKER ASSEMBLY)


    1. Disconnect the T20 stereo component amplifier assembly connector.

    2. Disconnect the O54 and O55 front No. 2 speaker assembly connectors.

    3. Measure the resistance according to the value(s) in the table below.

      Standard Resistance
      Tester Connection Condition Specified Condition
      T20-13 (FR+) - O54-2 (+) Always Below 1 Ω
      T20-28 (FR-) - O54-1 (-) Always Below 1 Ω
      T20-12 (FL+) - O55-2 (+) Always Below 1 Ω
      T20-27 (FL-) - O55-1 (-) Always Below 1 Ω
      T20-13 (FR+) or O54-2 (+) - Body ground Always 10 kΩ or higher
      T20-28 (FR-) or O54-1 (-) - Body ground Always 10 kΩ or higher
      T20-12 (FL+) or O55-2 (+) - Body ground Always 10 kΩ or higher
      T20-27 (FL-) or O55-1 (-) - Body ground Always 10 kΩ or higher
      Result
      Proceed to
      OK
      NG

    NG

    REPAIR OR REPLACE HARNESS OR CONNECTOR

    OK

  15. REPLACE FRONT NO. 2 SPEAKER ASSEMBLY


    1. Remove the front No. 2 speaker assembly.

      Click here

    2. Inspect the front No. 2 speaker assembly.

      Click here

      OK
      Malfunction disappears.
      Result
      Proceed to
      OK
      NG

    OK

    END

    NG

    PROCEED TO NEXT SUSPECTED AREA SHOWN IN PROBLEM SYMPTOMS TABLE Click here

  16. CHECK HARNESS AND CONNECTOR (STEREO COMPONENT AMPLIFIER ASSEMBLY - FRONT NO. 1 SPEAKER ASSEMBLY)


    1. Disconnect the T20 stereo component amplifier assembly connector.

    2. Disconnect the R14 and S14 front No. 1 speaker assembly connectors.

    3. Measure the resistance according to the value(s) in the table below.

      Standard Resistance
      Tester Connection Condition Specified Condition
      T20-5 (WFR+) - R14-1 Always Below 1 Ω
      T20-20 (WFR-) - R14-2 Always Below 1 Ω
      T20-4 (WFL+) - S14-1 Always Below 1 Ω
      T20-19 (WFL-) - S14-2 Always Below 1 Ω
      T20-5 (WFR+) or R14-1 - Body ground Always 10 kΩ or higher
      T20-20 (WFR-) or R14-2 - Body ground Always 10 kΩ or higher
      T20-4 (WFL+) or S14-1 - Body ground Always 10 kΩ or higher
      T20-19 (WFL-) or S14-2 - Body ground Always 10 kΩ or higher
      Result
      Proceed to
      OK
      NG

    NG

    REPAIR OR REPLACE HARNESS OR CONNECTOR

    OK

  17. INSPECT FRONT NO. 1 SPEAKER ASSEMBLY


    1. Remove the front No. 1 speaker assembly.

      Click here

    2. Inspect the front No. 1 speaker assembly.

      Click here

      Result
      Proceed to
      OK
      NG

    OK

    PROCEED TO NEXT SUSPECTED AREA SHOWN IN PROBLEM SYMPTOMS TABLE Click here

    NG

    REPLACE FRONT NO. 1 SPEAKER ASSEMBLY Click here

  18. CHECK HARNESS AND CONNECTOR (STEREO COMPONENT AMPLIFIER ASSEMBLY - FRONT NO. 3 SPEAKER ASSEMBLY)


    1. Disconnect the T20 stereo component amplifier assembly connector.

    2. Disconnect the O56 front No. 3 speaker assembly connector.

    3. Measure the resistance according to the value(s) in the table below.

      Standard Resistance
      Tester Connection Condition Specified Condition
      T20-7 (CTR+) - O56-2 (+) Always Below 1 Ω
      T20-22 (CTR-) - O56-1 (-) Always Below 1 Ω
      T20-7 (CTR+) or O56-2 (+) - Body ground Always 10 kΩ or higher
      T20-22 (CTR-) or O56-1 (-) - Body ground Always 10 kΩ or higher
      Result
      Proceed to
      OK
      NG

    NG

    REPAIR OR REPLACE HARNESS OR CONNECTOR

    OK

  19. REPLACE FRONT NO. 3 SPEAKER ASSEMBLY


    1. Remove the front No. 3 speaker assembly.

      Click here

    2. Inspect the front No. 3 speaker assembly.

      Click here

      OK
      Malfunction disappears.
      Result
      Proceed to
      OK
      NG

    OK

    END

    NG

    PROCEED TO NEXT SUSPECTED AREA SHOWN IN PROBLEM SYMPTOMS TABLE Click here

  20. CHECK HARNESS AND CONNECTOR (STEREO COMPONENT AMPLIFIER ASSEMBLY - REAR NO. 2 SPEAKER ASSEMBLY)


    1. Disconnect the T20 stereo component amplifier assembly connector.

    2. Disconnect the T26 and U36 rear No. 2 speaker assembly connectors.

    3. Measure the resistance according to the value(s) in the table below.

      Standard Resistance
      Tester Connection Condition Specified Condition
      T20-15 (RR+) - T26-3 (+TW) Always Below 1 Ω
      T20-30 (RR-) - T26-1 (-TW) Always Below 1 Ω
      T20-14 (RL+) - U36-3 (+TW) Always Below 1 Ω
      T20-29 (RL-) - U36-1 (-TW) Always Below 1 Ω
      T20-15 (RR+) or T26-3 (+TW) - Body ground Always 10 kΩ or higher
      T20-30 (RR-) or T26-1 (-TW) - Body ground Always 10 kΩ or higher
      T20-14 (RL+) or U36-3 (+TW) - Body ground Always 10 kΩ or higher
      T20-29 (RL-) or U36-1 (-TW) - Body ground Always 10 kΩ or higher
      Result
      Proceed to
      OK
      NG

    NG

    REPAIR OR REPLACE HARNESS OR CONNECTOR

    OK

  21. CHECK HARNESS AND CONNECTOR (REAR SPEAKER ASSEMBLY - REAR NO. 2 SPEAKER ASSEMBLY)


    1. Disconnect the T25 and U35 rear speaker assembly connectors.

    2. Disconnect the T26 and U36 rear No. 2 speaker assembly connectors.

    3. Measure the resistance according to the value(s) in the table below.

      Standard Resistance
      Tester Connection Condition Specified Condition
      T25-1 - T26-4 (+) Always Below 1 Ω
      T25-2 - T26-2 (-) Always Below 1 Ω
      U35-1 - U36-4 (+) Always Below 1 Ω
      U35-2 - U36-2 (-) Always Below 1 Ω
      T25-1 or T26-4 (+) - Body ground Always 10 kΩ or higher
      T25-2 or T26-2 (-) - Body ground Always 10 kΩ or higher
      U35-1 or U36-4 (+) - Body ground Always 10 kΩ or higher
      U35-2 or U36-2 (-) - Body ground Always 10 kΩ or higher
      Result
      Proceed to
      OK
      NG

    NG

    REPAIR OR REPLACE HARNESS OR CONNECTOR

    OK

  22. REPLACE REAR NO. 2 SPEAKER ASSEMBLY


    1. Remove the rear No. 2 speaker assembly.

      Click here

    2. Inspect the rear No. 2 speaker assembly.

      Click here

      OK
      Malfunction disappears.
      Result
      Proceed to
      OK
      NG

    OK

    END

    NG

  23. INSPECT REAR SPEAKER ASSEMBLY


    1. Remove the rear speaker assembly.

      Click here

    2. Inspect the rear speaker assembly.

      Click here

      Result
      Proceed to
      OK
      NG

    OK

    PROCEED TO NEXT SUSPECTED AREA SHOWN IN PROBLEM SYMPTOMS TABLE Click here

    NG

    REPLACE REAR SPEAKER ASSEMBLY Click here

  24. CHECK HARNESS AND CONNECTOR (STEREO COMPONENT AMPLIFIER ASSEMBLY - REAR HEADER SPEAKER ASSEMBLY)


    1. Disconnect the T20 stereo component amplifier assembly connector.

    2. Disconnect the T23 and U34 rear header speaker assembly connectors.

    3. Measure the resistance according to the value(s) in the table below.

      Standard Resistance
      Tester Connection Condition Specified Condition
      T20-11 (SR+) - T23-2 Always Below 1 Ω
      T20-26 (SR-) - T23-1 Always Below 1 Ω
      T20-10 (SL+) - U34-2 Always Below 1 Ω
      T20-25 (SL-) - U34-1 Always Below 1 Ω
      T20-11 (SR+) or T23-2 - Body ground Always 10 kΩ or higher
      T20-26 (SR-) or T23-1 - Body ground Always 10 kΩ or higher
      T20-10 (SL+) or U34-2 - Body ground Always 10 kΩ or higher
      T20-25 (SL-) or U34-1 - Body ground Always 10 kΩ or higher
      Result
      Proceed to
      OK
      NG

    NG

    REPAIR OR REPLACE HARNESS OR CONNECTOR

    OK

  25. REPLACE REAR HEADER SPEAKER ASSEMBLY


    1. Remove the rear header speaker assembly.

      Click here

    2. Inspect the rear header speaker assembly.

      Click here

      OK
      Malfunction disappears.
      Result
      Proceed to
      OK
      NG

    OK

    END

    NG

    PROCEED TO NEXT SUSPECTED AREA SHOWN IN PROBLEM SYMPTOMS TABLE Click here

  26. CHECK HARNESS AND CONNECTOR (STEREO COMPONENT AMPLIFIER ASSEMBLY - REAR NO. 3 SPEAKER ASSEMBLY)


    1. Disconnect the T20 stereo component amplifier assembly connector.

    2. Disconnect the T24 rear No. 3 speaker assembly connector.

    3. Measure the resistance according to the value(s) in the table below.

      Standard Resistance
      Tester Connection Condition Specified Condition
      T20-6 (WF1+) - T24-1 Always Below 1 Ω
      T20-21 (WF1-) - T24-2 Always Below 1 Ω
      T20-6 (WF1+) or T24-1 - Body ground Always 10 kΩ or higher
      T20-21 (WF1-) or T24-2 - Body ground Always 10 kΩ or higher
      Result
      Proceed to
      OK
      NG

    NG

    REPAIR OR REPLACE HARNESS OR CONNECTOR

    OK

  27. INSPECT REAR NO. 3 SPEAKER ASSEMBLY


    1. Remove the rear No. 3 speaker assembly.

      Click here

    2. Inspect the rear No. 3 speaker assembly.

      Click here

      Result
      Proceed to
      OK
      NG

    OK

    PROCEED TO NEXT SUSPECTED AREA SHOWN IN PROBLEM SYMPTOMS TABLE Click here

    NG

    REPLACE REAR NO. 3 SPEAKER ASSEMBLY Click here