AUDIO AND VISUAL SYSTEM(w/ Remote Touch) CUSTOMIZE PARAMETERS


  1. CUSTOMIZING WITH MULTI-DISPLAY


    1. Turn the engine switch on (IG).

    2. Enter the following menus: Setup / General / General Settings.

    3. Select the setting by referring to the table below.

      Item Default Content Setting Relevant ECU
      Feedback Force LEVEL3 (middle bar) Touchpad vibration feedback reaction force setting of the remote touch* LEVEL1 (No Vibration)/LEVEL2/LEVEL3/LEVEL4/LEVEL5 Radio receiver assembly

      Tech Tips

      *: The higher the set value, the stronger the touchpad vibration feedback reaction force becomes.

  2. CUSTOMIZING WITH REMOTE TOUCH


    1. Customizing with remote touch example


      1. Turn the engine switch on (IG).

      2. A01TDTFC01
        *a Example

        Simultaneously press and hold the applicable switches for 5 seconds or more.

      3. A01TDTVC01
        *a Example

        While pressing and holding the applicable switches*, use 2 fingers from your other hand to touch the touchpad.

      4. A01TDTPC01
        *a Example

        Check that the setting changes and the answer-back function vibrates the specified number of times.

      5. Release the applicable switches* to set the customize setting.

        Tech Tips


        • Repeat steps ii through v until the desired setting is selected.

        • *: The combination of switches pressed and held differs depending on the item to be customized.

    2. Customize pointer/cursor movement speed

      Tech Tips

      The speed at which the pointer/cursor moves when the touchpad is touched with a finger can be changed.


      1. A01TDTAC37
        *a Up Switch
        *b "MENU" Switch

        Following "Customizing with remote touch example", simultaneously press the "MENU" switch and up switch and perform the procedure.

      2. Determine the pointer/cursor movement speed from the number of times answer-back vibration is generated by the remote touch (remote operation controller assembly).

        Setting
        Pointer/Cursor Movement Speed Answer-back Vibrations

        Average

        (Default)

        		 2
        Fast 3
        Slow 1

        Tech Tips

        The settings cycle in the following order: "Average", "Fast", "Slow".

    3. Customize flick operation sensitivity

      Tech Tips

      The flick operation sensitivity for when a finger is quickly swiped on the touchpad can be changed.


      1. A01TDTAC38
        *a Up Switch
        *b Home Switch (w/ Home Switch)
        *c "MAP" Switch (w/ "MAP" Switch)

        Following "Customizing with remote touch example", simultaneously press the up switch and home switch*1 or "MAP" switch*2 and perform the procedure.


        • *1 w/ Home Switch

        • *2 w/ "MAP" Switch

      2. Determine the flick operation sensitivity from the number of times answer-back vibration is generated by the remote touch (remote operation controller assembly).

        Setting
        Flick Operation Recognition Speed Answer-back Vibrations

        Average

        (Default)

        		 1
        Fast 3
        Slow 2

        Tech Tips


        • When the customize setting is set to "Average", a flick operation is recognized when a finger is quickly swiped on the touchpad.

        • When the customize setting is set to "Fast", a flick operation is recognized when a finger is very quickly swiped on the touchpad.

        • When the customize setting is set to "Slow", a flick operation is recognized when a finger is somewhat quickly swiped on the touchpad.

        • The settings cycle in the following order: "Average", "Fast", "Slow".

    4. Customize screen (map/list) scroll direction during flick operation

      Tech Tips

      The screen (map/list) scroll direction for when a finger is used to flick the touchpad can be changed.


      1. A01TDTAC39
        *a "MENU" Switch
        *b Home Switch (w/ Home Switch)
        *c "MAP" Switch (w/ MAP Switch)

        Following "Customizing with remote touch example", simultaneously press the "MENU" switch and home switch*1 or "MAP" switch*2 and perform the procedure.


        • *1 w/ Home Switch

        • *2 w/ "MAP" Switch

      2. Determine the screen (map/list) scroll direction during a flick operation from the number of times answer-back vibration is generated by the remote touch (remote operation controller assembly).

        Setting
        Screen (map/list) scroll direction during flick operation Answer-back Vibrations

        Same Direction as Flick Operation

        (Default)

        		 2
        Opposite Direction of Flick Operation 1

        Tech Tips


        • When the customize setting is set to "Same Direction as Flick Operation", the screen (map/list) scrolls in the same direction as the finger used to flick the touchpad.

        • When the customize setting is set to "Opposite Direction of Flick Operation", the screen (map/list) scrolls in the opposite direction of the finger used to flick the touchpad.

    5. Customize pinch in/out operation function availability

      Tech Tips

      The availability of the zoom-in/zoom-out function of the map screen when fingers are used to pinch in/out on the touchpad can be changed.


      1. A01TDTAC40
        *a Down Switch
        *b Home Switch (w/ Home Switch)
        *c "MAP" Switch (w/ "MAP" Switch)

        Following "Customizing with remote touch example", simultaneously press the down switch and home switch*1 or "MAP" switch*2 and perform the procedure.


        • *1 w/ Home Switch

        • *2 w/ "MAP Switch

      2. Determine the pinch in/out operation function availability from the number of times answer-back vibration is generated by the remote touch (remote operation controller assembly).

        Setting
        Pinch In/Out Operation Function Availability Answer-back Vibrations

        Function enabled

        (Default)

        		 2
        Function disabled 1

    6. Customize Flick Operation Function Availability

      Tech Tips

      The availability of the flick operation function on the map screen and list screens (screens with a vertical scroll tab) when a finger is used to flick the touchpad can be changed.


      1. A01TDTAC41
        *a Up Switch
        *b "MENU" Switch
        *c Home Switch (w/ Home Switch)
        *d "MAP" Switch (w/ "MAP" Switch)

        Following "Customizing with remote touch example", simultaneously press the "MENU" switch and home switch*1 or "MAP" switch*2, up switch and perform the procedure.


        • *1 w/ Home Switch

        • *2 w/ "MAP" Switch

      2. Determine the flick operation function availability from the number of times answer-back vibration is generated by the remote touch (remote operation controller assembly).

        Setting
        Flick Operation Function Availability Answer-back Vibrations

        Map Function Enabled, List Function Enabled

        (Default)

        		 1
        Map Function Enabled, List Function Disabled 2
        Map Function Disabled, List Function Disabled 3
        Map Function Disabled, List Function Enabled 4

        Tech Tips


        • When the customize setting is set to "Map Function Disabled, List Function Enabled" the flick operation cannot be used on the map screen, but can be used on list screens (screens with a vertical scroll tab).

        • When the customize setting is set to "Map Function Enabled, List Function Enabled" the flick operation can be used on both the map screen and list screens (screens with a vertical scroll tab).

        • When the customize setting is set to "Map Function Enabled, List Function Disabled" the flick operation can be used on the map screen, but cannot be used on list screens (screens with a vertical scroll tab).

        • When the customize setting is set to "Map Function Disabled, List Function Disabled" the flick operation cannot be used on the map screen or list screens (screens with a vertical scroll tab).

        • The settings cycle in the following order: "Map Function Enabled, List Function Enabled", "Map Function Enabled, List Function Disabled", "Map Function Disabled, List Function Disabled", "Map Function Disabled, List Function Enabled".