NAVIGATION SYSTEM, Diagnostic DTC:B1323, B1324

DTC Code DTC Name
B1323 Lost Communication with Haptic Device
B1324 Lost Communication with Meter

DESCRIPTION

These DTCs are stored when communication between the radio receiver assembly and combination meter assembly or remote touch (remote operation controller assembly) is not possible.

Tech Tips

The radio receiver assembly is the master unit.

DTC No. Detection Item DTC Detection Condition Trouble Area
B1323 Lost Communication with Haptic Device CAN reception error

  • Local bus communication line

  • Remote touch (remote operation controller assembly) power source circuit

  • Remote touch (remote operation controller assembly)

  • Radio receiver assembly

  • Harness or connector

  • No. 15 CAN junction connector (for LHD)

  • No. 8 CAN junction connector (for RHD)

  • Stop and start system*
B1324 Lost Communication with Meter CAN reception error

  • Local bus communication line

  • Combination meter assembly power source circuit

  • Combination meter assembly

  • Radio receiver assembly

  • Harness or connector

  • No. 15 CAN junction connector (for LHD)

  • No. 8 CAN junction connector (for RHD)

  • Stop and start system*

WIRING DIAGRAM

Figure 1. for LHD

B0075YJE03

Figure 2. for RHD

B0075YJE04

CAUTION / NOTICE / HINT

Note


  • Depending on the parts that are replaced during vehicle inspection or maintenance, performing initialization, registration or calibration may be needed. Refer to Precaution for Navigation System.

    Click here

  • When replacing the radio receiver assembly, always replace it with a new one. If a radio receiver assembly which was installed to another vehicle is used, the following may occur:


    • A communication malfunction DTC may be stored.

    • The radio receiver assembly may not operate normally.

  • Inspect the fuses for circuits related to this system before performing the following procedure.

PROCEDURE


  1. CHECK MODEL


    1. Choose the model to be inspected.

      Result
      Result Proceed to
      for LHD A
      for RHD B

    B

    CHECK DTC Click here

    A

  2. CHECK DTC


    1. Check for DTCs and check that no DTCs are output.


      Body Electrical > Navigation System > Trouble Codes
      Result
      Result Proceed to
      DTC B1323 and B1324 are not output A
      DTC B1323 and B1324 are output B
      DTC B1323 is output C
      DTC B1324 is output D

    A

    USE SIMULATION METHOD TO CHECK Click here

    C

    CHECK HARNESS AND CONNECTOR (REMOTE TOUCH (REMOTE OPERATION CONTROLLER ASSEMBLY) POWER SOURCE) Click here

    D

    CHECK HARNESS AND CONNECTOR (COMBINATION METER ASSEMBLY POWER SOURCE) Click here

    B

  3. CHECK LOCAL BUS


    1. Disconnect the cable from the negative (-) battery terminal.

    2. Measure the resistance according to the value(s) in the table below.

      Standard Resistance
      Tester Connection Condition Specified Condition
      O196-9 - O196-20 Cable disconnected from negative (-) battery terminal 54 to 69 Ω
      Result
      Result Proceed to
      OK A
      NG (Below 54 Ω) B
      NG (70 Ω or higher) C

    A

    USE SIMULATION METHOD TO CHECK Click here

    C

    CHECK HARNESS AND CONNECTOR (RADIO RECEIVER ASSEMBLY - NO. 15 JUNCTION CONNECTOR) Click here

    B

  4. CHECK HARNESS AND CONNECTOR (RADIO RECEIVER ASSEMBLY - NO. 15 CAN JUNCTION CONNECTOR)


    1. Disconnect the cable from the negative (-) battery terminal.

    2. Disconnect the O196 No. 15 CAN junction connector.

    3. Connect the O159 radio receiver assembly connector.

    4. Measure the resistance according to the value(s) in the table below.

      Standard Resistance
      Tester Connection Condition Specified Condition
      O196-9 - O196-20 Cable disconnected from negative (-) battery terminal 108 to 132 Ω
      Result
      Proceed to
      OK
      NG

    NG

    CHECK HARNESS AND CONNECTOR (RADIO RECEIVER ASSEMBLY - NO. 15 CAN JUNCTION CONNECTOR) Click here

    OK

  5. CHECK HARNESS AND CONNECTOR (COMBINATION METER ASSEMBLY - NO. 15 CAN JUNCTION CONNECTOR)


    1. Disconnect the cable from the negative (-) battery terminal.

    2. Disconnect the O196 No. 15 CAN junction connector.

    3. Connect the O4 combination meter assembly connector.

    4. Measure the resistance according to the value(s) in the table below.

      Standard Resistance
      Tester Connection Condition Specified Condition
      O196-10 - O196-21 Cable disconnected from negative (-) battery terminal 200 Ω or higher
      Result
      Proceed to
      OK
      NG

    NG

    CHECK HARNESS AND CONNECTOR (COMBINATION METER ASSEMBLY - NO. 15 CAN JUNCTION CONNECTOR) Click here

    OK

  6. CHECK HARNESS AND CONNECTOR (REMOTE TOUCH (REMOTE OPERATION CONTROLLER ASSEMBLY) - NO. 15 CAN JUNCTION CONNECTOR)


    1. Disconnect the cable from the negative (-) battery terminal.

    2. Disconnect the O196 No. 15 CAN junction connector.

    3. Connect the O165 remote touch (remote operation controller assembly) connector.

    4. Measure the resistance according to the value(s) in the table below.

      Standard Resistance
      Tester Connection Condition Specified Condition
      O196-11 - O196-22 Cable disconnected from negative (-) battery terminal 108 to 132 Ω
      Result
      Proceed to
      OK
      NG

    OK

    REPLACE NO. 15 CAN JUNCTION CONNECTOR

    NG

  7. CHECK HARNESS AND CONNECTOR (REMOTE TOUCH (REMOTE OPERATION CONTROLLER ASSEMBLY) - NO. 15 CAN JUNCTION CONNECTOR)


    1. Disconnect the cable from the negative (-) battery terminal.

    2. Disconnect the O165 remote touch (remote operation controller assembly) connector.

    3. Connect the O196 No. 15 CAN junction connector.

    4. Measure the resistance according to the value(s) in the table below.

      Standard Resistance
      Tester Connection Condition Specified Condition
      O165-9 (MO+) - O165-8 (MO-) Cable disconnected from negative (-) battery terminal 108 to 132 Ω
      Result
      Proceed to
      OK
      NG

    OK

    REPLACE REMOTE TOUCH (REMOTE OPERATION CONTROLLER ASSEMBLY) Click here

    NG

    REPAIR OR REPLACE HARNESS OR CONNECTOR

  8. CHECK HARNESS AND CONNECTOR (COMBINATION METER ASSEMBLY - NO. 15 CAN JUNCTION CONNECTOR)


    1. Disconnect the cable from the negative (-) battery terminal.

    2. Disconnect the O4 combination meter assembly connector.

    3. Connect the O196 No. 15 CAN junction connector.

    4. Measure the resistance according to the value(s) in the table below.

      Standard Resistance
      Tester Connection Condition Specified Condition
      O4-10 (MSCH) - O4-9 (MSCL) Cable disconnected from negative (-) battery terminal 54 to 69 Ω
      Result
      Proceed to
      OK
      NG

    OK

    REPLACE COMBINATION METER ASSEMBLY Click here

    NG

    REPAIR OR REPLACE HARNESS OR CONNECTOR

  9. CHECK HARNESS AND CONNECTOR (RADIO RECEIVER ASSEMBLY - NO. 15 CAN JUNCTION CONNECTOR)


    1. Disconnect the cable from the negative (-) battery terminal.

    2. Disconnect the O159 radio receiver assembly connector.

    3. Connect the O196 No. 15 CAN junction connector.

    4. Measure the resistance according to the value(s) in the table below.

      Standard Resistance
      Tester Connection Condition Specified Condition
      O159-5 (CNH1) - O159-6 (CNL1) Cable disconnected from negative (-) battery terminal 108 to 132 Ω
      Result
      Proceed to
      OK
      NG

    OK

    REPLACE RADIO RECEIVER ASSEMBLY Click here

    NG

    REPAIR OR REPLACE HARNESS OR CONNECTOR

  10. CHECK HARNESS AND CONNECTOR (RADIO RECEIVER ASSEMBLY - NO. 15 JUNCTION CONNECTOR)


    1. Disconnect the cable from the negative (-) battery terminal.

    2. Disconnect the O159 radio receiver assembly connector.

    3. Connect the O196 No. 15 CAN junction connector.

    4. Measure the resistance according to the value(s) in the table below.

      Standard Resistance
      Tester Connection Condition Specified Condition
      O159-5 (CNH1) - O159-6 (CNL1) Cable disconnected from negative (-) battery terminal 108 to 132 Ω
      Result
      Proceed to
      OK
      NG

    OK

    REPLACE RADIO RECEIVER ASSEMBLY Click here

    NG

  11. CHECK HARNESS AND CONNECTOR (RADIO RECEIVER ASSEMBLY - NO. 15 CAN JUNCTION CONNECTOR)


    1. Disconnect the cable from the negative (-) battery terminal.

    2. Disconnect the O196 No. 15 CAN junction connector.

    3. Connect the O159 radio receiver assembly connector.

    4. Measure the resistance according to the value(s) in the table below.

      Standard Resistance
      Tester Connection Condition Specified Condition
      O196-9 - O196-20 Cable disconnected from negative (-) battery terminal 108 to 132 Ω
      Result
      Proceed to
      OK
      NG

    OK

    REPLACE NO. 15 CAN JUNCTION CONNECTOR

    NG

    REPAIR OR REPLACE HARNESS OR CONNECTOR

  12. CHECK HARNESS AND CONNECTOR (REMOTE TOUCH (REMOTE OPERATION CONTROLLER ASSEMBLY) POWER SOURCE)


    1. Disconnect the O165 remote touch (remote operation controller assembly) connector.

    2. Measure the resistance according to the value(s) in the table below.

      Standard Resistance
      Tester Connection Condition Specified Condition
      O165-10 (GND) - Body ground Always Below 1 Ω

    3. Measure the voltage according to the value(s) in the table below.

      Standard Voltage
      Tester Connection Condition Specified Condition
      O165-1 (+B) - Body ground Always

      11 to 14 V*1

      10.5 to 16 V*2
      O165-6 (ACC) - Body ground Engine switch on (ACC)

      11 to 14 V*1

      10.5 to 16 V*2

      • *1: w/o Stop and Start System

        *2: w/ Stop and Start System

      Result
      Result Proceed to
      OK A
      NG (w/o Stop and Start System) B
      NG (w/ Stop and Start System) C

    B

    REPAIR OR REPLACE HARNESS OR CONNECTOR

    C

    GO TO STOP AND START SYSTEM Click here

    A

  13. CHECK HARNESS AND CONNECTOR (REMOTE TOUCH (REMOTE OPERATION CONTROLLER ASSEMBLY) - NO. 15 CAN JUNCTION CONNECTOR)


    1. Disconnect the cable from the negative (-) battery terminal.

    2. Disconnect the O196 No. 15 CAN junction connector.

    3. Connect the O165 remote touch (remote operation controller assembly) connector.

    4. Measure the resistance according to the value(s) in the table below.

      Standard Resistance
      Tester Connection Condition Specified Condition
      O196-11 - O196-22 Cable disconnected from negative (-) battery terminal 108 to 132 Ω
      Result
      Proceed to
      OK
      NG

    OK

    REPLACE NO. 15 CAN JUNCTION CONNECTOR

    NG

  14. CHECK HARNESS AND CONNECTOR (REMOTE TOUCH (REMOTE OPERATION CONTROLLER ASSEMBLY) - NO. 15 CAN JUNCTION CONNECTOR)


    1. Disconnect the cable from the negative (-) battery terminal.

    2. Disconnect the O165 remote touch (remote operation controller assembly) connector.

    3. Connect the O196 No. 15 CAN junction connector.

    4. Measure the resistance according to the value(s) in the table below.

      Standard Resistance
      Tester Connection Condition Specified Condition
      O165-9 (MO+) - O165-8 (MO-) Cable disconnected from negative (-) battery terminal 108 to 132 Ω
      Result
      Proceed to
      OK
      NG

    OK

    REPLACE REMOTE TOUCH (REMOTE OPERATION CONTROLLER ASSEMBLY) Click here

    NG

    REPAIR OR REPLACE HARNESS OR CONNECTOR

  15. CHECK HARNESS AND CONNECTOR (COMBINATION METER ASSEMBLY POWER SOURCE)


    1. Disconnect the O3 combination meter assembly connector.

    2. Measure the resistance according to the value(s) in the table below.

      Standard Resistance
      Tester Connection Condition Specified Condition
      O3-31 (ES) - Body ground Always Below 1 Ω

    3. Measure the voltage according to the value(s) in the table below.

      Standard Voltage
      Tester Connection Condition Specified Condition
      O3-22 (B) - Body ground Always 11 to 14 V
      O3-21 (IG+) - Body ground Engine switch on (IG)

      11 to 14 V*1

      10.5 to 16 V*2

      • *1: w/o Stop and Start System

        *2: w/ Stop and Start System

      Result
      Result Proceed to
      OK A
      NG (w/o Stop and Start System) B
      NG (w/ Stop and Start System) C

    B

    REPAIR OR REPLACE HARNESS OR CONNECTOR

    C

    GO TO STOP AND START SYSTEM Click here

    A

  16. CHECK HARNESS AND CONNECTOR (COMBINATION METER ASSEMBLY - NO. 15 CAN JUNCTION CONNECTOR)


    1. Disconnect the cable from the negative (-) battery terminal.

    2. Disconnect the O196 No. 15 CAN junction connector.

    3. Connect the O3 combination meter assembly connector.

    4. Measure the resistance according to the value(s) in the table below.

      Standard Resistance
      Tester Connection Condition Specified Condition
      O196-10 - O196-21 Cable disconnected from negative (-) battery terminal 200 Ω or higher
      Result
      Proceed to
      OK
      NG

    OK

    REPLACE NO. 15 CAN JUNCTION CONNECTOR

    NG

  17. CHECK HARNESS AND CONNECTOR (COMBINATION METER ASSEMBLY - NO. 15 CAN JUNCTION CONNECTOR)


    1. Disconnect the cable from the negative (-) battery terminal.

    2. Disconnect the O4 combination meter assembly connector.

    3. Connect the O196 No. 15 CAN junction connector.

    4. Measure the resistance according to the value(s) in the table below.

      Standard Resistance
      Tester Connection Condition Specified Condition
      O4-10 (MSCH) - O4-9 (MSCL) Cable disconnected from negative (-) battery terminal 54 to 69 Ω
      Result
      Proceed to
      OK
      NG

    OK

    REPLACE COMBINATION METER ASSEMBLY Click here

    NG

    REPAIR OR REPLACE HARNESS OR CONNECTOR

  18. CHECK DTC


    1. Check for DTCs and check that no DTCs are output.


      Body Electrical > Navigation System > Trouble Codes
      Result
      Result Proceed to
      DTC B1323 and B1324 are not output A
      DTC B1323 and B1324 are output B
      DTC B1323 is output C
      DTC B1324 is output D

    A

    USE SIMULATION METHOD TO CHECK Click here

    C

    CHECK HARNESS AND CONNECTOR (REMOTE TOUCH (REMOTE OPERATION CONTROLLER ASSEMBLY) POWER SOURCE) Click here

    D

    CHECK HARNESS AND CONNECTOR (COMBINATION METER ASSEMBLY POWER SOURCE) Click here

    B

  19. CHECK LOCAL BUS


    1. Disconnect the cable from the negative (-) battery terminal.

    2. Measure the resistance according to the value(s) in the table below.

      Standard Resistance
      Tester Connection Condition Specified Condition
      O110-9 - O110-20 Cable disconnected from negative (-) battery terminal 54 to 69 Ω
      Result
      Result Proceed to
      OK A
      NG (Below 54 Ω) B
      NG (70 Ω or higher) C

    A

    USE SIMULATION METHOD TO CHECK Click here

    C

    CHECK HARNESS AND CONNECTOR (RADIO RECEIVER ASSEMBLY - NO. 8 JUNCTION CONNECTOR) Click here

    B

  20. CHECK HARNESS AND CONNECTOR (RADIO RECEIVER ASSEMBLY - NO. 8 CAN JUNCTION CONNECTOR)


    1. Disconnect the cable from the negative (-) battery terminal.

    2. Disconnect the O110 No. 8 CAN junction connector.

    3. Connect the O159 radio receiver assembly connector.

    4. Measure the resistance according to the value(s) in the table below.

      Standard Resistance
      Tester Connection Condition Specified Condition
      O110-9 - O110-20 Cable disconnected from negative (-) battery terminal 108 to 132 Ω
      Result
      Proceed to
      OK
      NG

    NG

    CHECK HARNESS AND CONNECTOR (RADIO RECEIVER ASSEMBLY - NO. 8 CAN JUNCTION CONNECTOR) Click here

    OK

  21. CHECK HARNESS AND CONNECTOR (COMBINATION METER ASSEMBLY - NO. 8 CAN JUNCTION CONNECTOR)


    1. Disconnect the cable from the negative (-) battery terminal.

    2. Disconnect the O110 No. 8 CAN junction connector.

    3. Connect the O4 combination meter assembly connector.

    4. Measure the resistance according to the value(s) in the table below.

      Standard Resistance
      Tester Connection Condition Specified Condition
      O110-10 - O110-21 Cable disconnected from negative (-) battery terminal 200 Ω or higher
      Result
      Proceed to
      OK
      NG

    NG

    CHECK HARNESS AND CONNECTOR (COMBINATION METER ASSEMBLY - NO. 8 CAN JUNCTION CONNECTOR) Click here

    OK

  22. CHECK HARNESS AND CONNECTOR (REMOTE TOUCH (REMOTE OPERATION CONTROLLER ASSEMBLY) - NO. 8 CAN JUNCTION CONNECTOR)


    1. Disconnect the cable from the negative (-) battery terminal.

    2. Disconnect the O110 No. 8 CAN junction connector.

    3. Connect the O165 remote touch (remote operation controller assembly) connector.

    4. Measure the resistance according to the value(s) in the table below.

      Standard Resistance
      Tester Connection Condition Specified Condition
      O110-11 - O110-22 Cable disconnected from negative (-) battery terminal 108 to 132 Ω
      Result
      Proceed to
      OK
      NG

    OK

    REPLACE NO. 8 CAN JUNCTION CONNECTOR

    NG

  23. CHECK HARNESS AND CONNECTOR (REMOTE TOUCH (REMOTE OPERATION CONTROLLER ASSEMBLY) - NO. 8 CAN JUNCTION CONNECTOR)


    1. Disconnect the cable from the negative (-) battery terminal.

    2. Disconnect the O165 remote touch (remote operation controller assembly) connector.

    3. Connect the O110 No. 8 CAN junction connector.

    4. Measure the resistance according to the value(s) in the table below.

      Standard Resistance
      Tester Connection Condition Specified Condition
      O165-9 (MO+) - O165-8 (MO-) Cable disconnected from negative (-) battery terminal 108 to 132 Ω
      Result
      Proceed to
      OK
      NG

    OK

    REPLACE REMOTE TOUCH (REMOTE OPERATION CONTROLLER ASSEMBLY) Click here

    NG

    REPAIR OR REPLACE HARNESS OR CONNECTOR

  24. CHECK HARNESS AND CONNECTOR (COMBINATION METER ASSEMBLY - NO. 8 CAN JUNCTION CONNECTOR)


    1. Disconnect the cable from the negative (-) battery terminal.

    2. Disconnect the O4 combination meter assembly connector.

    3. Connect the O110 No. 8 CAN junction connector.

    4. Measure the resistance according to the value(s) in the table below.

      Standard Resistance
      Tester Connection Condition Specified Condition
      O4-10 (MSCH) - O4-9 (MSCL) Cable disconnected from negative (-) battery terminal 54 to 69 Ω
      Result
      Proceed to
      OK
      NG

    OK

    REPLACE COMBINATION METER ASSEMBLY Click here

    NG

    REPAIR OR REPLACE HARNESS OR CONNECTOR

  25. CHECK HARNESS AND CONNECTOR (RADIO RECEIVER ASSEMBLY - NO. 8 CAN JUNCTION CONNECTOR)


    1. Disconnect the cable from the negative (-) battery terminal.

    2. Disconnect the O159 radio receiver assembly connector.

    3. Connect the O110 No. 8 CAN junction connector.

    4. Measure the resistance according to the value(s) in the table below.

      Standard Resistance
      Tester Connection Condition Specified Condition
      O159-5 (CNH1) - O159-6 (CNL1) Cable disconnected from negative (-) battery terminal 108 to 132 Ω
      Result
      Proceed to
      OK
      NG

    OK

    REPLACE RADIO RECEIVER ASSEMBLY Click here

    NG

    REPAIR OR REPLACE HARNESS OR CONNECTOR

  26. CHECK HARNESS AND CONNECTOR (RADIO RECEIVER ASSEMBLY - NO. 8 JUNCTION CONNECTOR)


    1. Disconnect the cable from the negative (-) battery terminal.

    2. Disconnect the O159 radio receiver assembly connector.

    3. Connect the O110 No. 8 CAN junction connector.

    4. Measure the resistance according to the value(s) in the table below.

      Standard Resistance
      Tester Connection Condition Specified Condition
      O159-5 (CNH1) - O159-6 (CNL1) Cable disconnected from negative (-) battery terminal 108 to 132 Ω
      Result
      Proceed to
      OK
      NG

    OK

    REPLACE RADIO RECEIVER ASSEMBLY Click here

    NG

  27. CHECK HARNESS AND CONNECTOR (RADIO RECEIVER ASSEMBLY - NO. 8 CAN JUNCTION CONNECTOR)


    1. Disconnect the cable from the negative (-) battery terminal.

    2. Disconnect the O110 No. 8 CAN junction connector.

    3. Connect the O159 radio receiver assembly connector.

    4. Measure the resistance according to the value(s) in the table below.

      Standard Resistance
      Tester Connection Condition Specified Condition
      O110-9 - O110-20 Cable disconnected from negative (-) battery terminal 108 to 132 Ω
      Result
      Proceed to
      OK
      NG

    OK

    REPLACE NO. 8 CAN JUNCTION CONNECTOR

    NG

    REPAIR OR REPLACE HARNESS OR CONNECTOR

  28. CHECK HARNESS AND CONNECTOR (REMOTE TOUCH (REMOTE OPERATION CONTROLLER ASSEMBLY) POWER SOURCE)


    1. Disconnect the O165 remote touch (remote operation controller assembly) connector.

    2. Measure the resistance according to the value(s) in the table below.

      Standard Resistance
      Tester Connection Condition Specified Condition
      O165-10 (GND) - Body ground Always Below 1 Ω

    3. Measure the voltage according to the value(s) in the table below.

      Standard Voltage
      Tester Connection Condition Specified Condition
      O165-1 (+B) - Body ground Always

      11 to 14 V*1

      10.5 to 16 V*2
      O165-6 (ACC) - Body ground Engine switch on (ACC)

      11 to 14 V*1

      10.5 to 16 V*2

      • *1: w/o Stop and Start System

        *2: w/ Stop and Start System

      Result
      Result Proceed to
      OK A
      NG (w/o Stop and Start System) B
      NG (w/ Stop and Start System) C

    B

    REPAIR OR REPLACE HARNESS OR CONNECTOR

    C

    GO TO STOP AND START SYSTEM Click here

    A

  29. CHECK HARNESS AND CONNECTOR (REMOTE TOUCH (REMOTE OPERATION CONTROLLER ASSEMBLY) - NO. 8 CAN JUNCTION CONNECTOR)


    1. Disconnect the cable from the negative (-) battery terminal.

    2. Disconnect the O110 No. 8 CAN junction connector.

    3. Connect the O165 remote touch (remote operation controller assembly) connector.

    4. Measure the resistance according to the value(s) in the table below.

      Standard Resistance
      Tester Connection Condition Specified Condition
      O110-11 - O110-22 Cable disconnected from negative (-) battery terminal 108 to 132 Ω
      Result
      Proceed to
      OK
      NG

    OK

    REPLACE NO. 8 CAN JUNCTION CONNECTOR

    NG

  30. CHECK HARNESS AND CONNECTOR (REMOTE TOUCH (REMOTE OPERATION CONTROLLER ASSEMBLY) - NO. 8 CAN JUNCTION CONNECTOR)


    1. Disconnect the cable from the negative (-) battery terminal.

    2. Disconnect the O165 remote touch (remote operation controller assembly) connector.

    3. Connect the O110 No. 8 CAN junction connector.

    4. Measure the resistance according to the value(s) in the table below.

      Standard Resistance
      Tester Connection Condition Specified Condition
      O165-9 (MO+) - O165-8 (MO-) Cable disconnected from negative (-) battery terminal 108 to 132 Ω
      Result
      Proceed to
      OK
      NG

    OK

    REPLACE REMOTE TOUCH (REMOTE OPERATION CONTROLLER ASSEMBLY) Click here

    NG

    REPAIR OR REPLACE HARNESS OR CONNECTOR

  31. CHECK HARNESS AND CONNECTOR (COMBINATION METER ASSEMBLY POWER SOURCE)


    1. Disconnect the O3 combination meter assembly connector.

    2. Measure the resistance according to the value(s) in the table below.

      Standard Resistance
      Tester Connection Condition Specified Condition
      O3-31 (ES) - Body ground Always Below 1 Ω

    3. Measure the voltage according to the value(s) in the table below.

      Standard Voltage
      Tester Connection Condition Specified Condition
      O3-22 (B) - Body ground Always 11 to 14 V
      O3-21 (IG+) - Body ground Engine switch on (IG)

      11 to 14 V*1

      10.5 to 16 V*2

      • *1: w/o Stop and Start System

        *2: w/ Stop and Start System

      Result
      Result Proceed to
      OK A
      NG (w/o Stop and Start System) B
      NG (w/ Stop and Start System) C

    B

    REPAIR OR REPLACE HARNESS OR CONNECTOR

    C

    GO TO STOP AND START SYSTEM Click here

    A

  32. CHECK HARNESS AND CONNECTOR (COMBINATION METER ASSEMBLY - NO. 8 CAN JUNCTION CONNECTOR)


    1. Disconnect the cable from the negative (-) battery terminal.

    2. Disconnect the O110 No. 8 CAN junction connector.

    3. Connect the O3 combination meter assembly connector.

    4. Measure the resistance according to the value(s) in the table below.

      Standard Resistance
      Tester Connection Condition Specified Condition
      O110-10 - O110-21 Cable disconnected from negative (-) battery terminal 200 Ω or higher
      Result
      Proceed to
      OK
      NG

    OK

    REPLACE NO. 8 CAN JUNCTION CONNECTOR

    NG

  33. CHECK HARNESS AND CONNECTOR (COMBINATION METER ASSEMBLY - NO. 8 CAN JUNCTION CONNECTOR)


    1. Disconnect the cable from the negative (-) battery terminal.

    2. Disconnect the O4 combination meter assembly connector.

    3. Connect the O110 No. 8 CAN junction connector.

    4. Measure the resistance according to the value(s) in the table below.

      Standard Resistance
      Tester Connection Condition Specified Condition
      O4-10 (MSCH) - O4-9 (MSCL) Cable disconnected from negative (-) battery terminal 54 to 69 Ω
      Result
      Proceed to
      OK
      NG

    OK

    REPLACE COMBINATION METER ASSEMBLY Click here

    NG

    REPAIR OR REPLACE HARNESS OR CONNECTOR