BLACK OUT TAPE (for Rear Door) REMOVAL

Tech Tips


  • Use the same procedure for the RH and LH sides.

  • The procedure listed below is for the LH side.

  • When removing the black out tape and window frame moulding, heat the vehicle body, black out tape and window frame moulding using a heat light.

Standard
Item Temperature
Vehicle Body 40 to 60°C (104 to 140°F)
Black Out Tape 20 to 30°C (68 to 86°F)
Window Frame Moulding 20 to 30°C (68 to 86°F)

Note

Do not heat the vehicle body, black out tape and window frame moulding excessively.


  1. REMOVE ENGINE ROOM SIDE COVER LH


    1. Remove the 7 clips and engine room side cover LH.

      A01EN5SE01

  2. DISCONNECT CABLE FROM NEGATIVE BATTERY TERMINAL

    Note


    • w/ Navigation System:

      After the engine switch is turned off, the HDD navigation system requires approximately 6 minutes to record various types of memory and settings. As a result, after turning the engine switch off, wait 6 minutes or more before disconnecting the cable from the negative (-) battery terminal.

    • When disconnecting the cable, some systems need to be initialized after the cable is reconnected Click here.

  3. REMOVE REAR DOOR INSIDE HANDLE BEZEL PLUG LH


    1. A01ENEKE01
      Text in Illustration
      *1 Protective Tape

      Using a screwdriver, detach the 3 claws and remove the rear door inside handle bezel plug LH.

      Tech Tips

      Tape the screwdriver tip before use.

  4. REMOVE REAR UPPER DOOR ARMREST BASE PANEL LH


    1. A01EO3E

      Using a moulding remover, detach the 6 claws.

    2. Disconnect the connector and remove the rear upper door armrest base panel LH and rear power window regulator switch assembly.

  5. REMOVE REAR DOOR TRIM BOARD SUB-ASSEMBLY LH


    1. A01ERTKE01

      Remove the 2 screws.

    2. Detach the 11 clips.

    3. Remove the rear inner door glass weatherstrip LH together with the rear door trim board sub-assembly LH by pulling them upward in the order shown in the illustration.

      Tech Tips

      Make sure that the pin labeled A in the illustration is detached from the door panel.

    4. Disconnect the connector.

    5. A01EPPA

      Disconnect the 2 cables from the rear door inside handle sub-assembly LH.

  6. REMOVE REAR INNER DOOR GLASS WEATHERSTRIP LH


    1. A01ENT3

      Detach the 4 clips and remove the front inner door glass weatherstrip LH from the front door trim board sub-assembly LH.

      Note


      • Squeeze the metal clip to remove it.

      • The metal clip may be deformed if it is forcibly pulled.

  7. REMOVE REAR DOOR TRIM COVER LH


    1. A01EOI1

      Detach the 7 clips and remove the rear door trim cover LH.

  8. REMOVE REAR DOOR SERVICE HOLE COVER LH


    1. A01ERCQ

      Using a clip remover, detach the 6 clamps.

    2. Remove the bolt and disconnect the 2 connectors.

    3. Remove the rear door service hole cover LH.

      Tech Tips

      Remove the remaining tape on the door.

  9. REMOVE REAR DOOR GLASS RUN LH


    1. A01ES1E

      Remove the rear door glass run LH from the window frame.

  10. REMOVE REAR DOOR REAR LOWER WINDOW FRAME SUB-ASSEMBLY LH


    1. A01EOAU

      Remove the 2 bolts.

    2. Remove the screw and rear door rear lower window frame sub-assembly LH.

  11. REMOVE REAR DOOR QUARTER WINDOW GLASS LH


    1. A01EP1N

      Remove the rear door quarter window glass LH and rear door quarter window weatherstrip LH as a unit as shown in the illustration.

  12. REMOVE REAR DOOR GLASS SUB-ASSEMBLY LH


    1. A01ENIQ

      Remove the rear door glass sub-assembly LH from the rear door window regulator sub-assembly as shown in the illustration.

      Note

      Do not damage the door glass.

  13. REMOVE REAR DOOR BELT MOULDING ASSEMBLY LH

    A01ERBXE01

    1. Put protective tape around the belt moulding.

    2. A01EO76

      Detach the claw and remove the belt moulding.

  14. REMOVE REAR DOOR FRONT WINDOW FRAME MOULDING LH

    A01EOTOE01

    1. Put protective tape around the window frame moulding.

    2. Detach the clip and remove the double-sided tape to remove the window frame moulding.

  15. REMOVE REAR DOOR FRAME GARNISH LH


    1. A01EP3X

      Detach the clip and remove the rear door frame garnish LH.

      Tech Tips

      The rear door frame garnish LH needs to be replaced with a new one because the clip will break when removing the rear door frame garnish LH.

  16. REMOVE REAR NO. 2 DOOR FRAME GARNISH LH


    1. A01EQ07

      Detach the clip and remove the rear No. 2 door frame garnish LH.

      Tech Tips

      The rear No. 2 door frame garnish LH needs to be replaced with a new one because the clip will break when removing the rear No. 2 door frame garnish LH.

  17. REMOVE REAR DOOR WEATHERSTRIP LH

    A01ENAL

    1. Remove the clip.

    2. Detach the 3 clips, and remove the upper part of the rear door weatherstrip so that the black out tape can be removed.

  18. REMOVE NO. 2 BLACK OUT TAPE LH

    A01EN94

    1. Pull back an edge of the black out tape and pull it parallel to the vehicle body to remove it.

  19. REMOVE NO. 6 BLACK OUT TAPE LH

    A01ERPZ

    1. Pull back an edge of the black out tape and pull it parallel to the vehicle body to remove it.

  20. REMOVE UPPER INNER BLACK OUT TAPE LH

    A01ER16

    1. Pull back an edge of the black out tape and pull it parallel to the vehicle body to remove it.

  21. REMOVE REAR INNER BLACK OUT TAPE LH

    A01ERDV

    1. Pull back an edge of the black out tape and pull it parallel to the vehicle body to remove it.