FRONT DOOR WINDOW FRAME MOULDING INSTALLATION

Tech Tips


  • Use the same procedure for the RH and LH sides.

  • The procedure listed below is for the LH side.

  • When installing the window frame moulding, heat the vehicle body and window frame moulding using a heat light.

Standard
Item Temperature
Vehicle Body 40 to 60°C (104 to 140°F)
Window Frame Moulding 20 to 30°C (68 to 86°F)

Note

Do not heat the vehicle body and window frame moulding excessively.


  1. INSTALL FRONT DOOR REAR WINDOW FRAME MOULDING LH


    1. Clean the vehicle body surface.


      1. Using a heat light, heat the vehicle body surface.

      2. Remove the double-sided tape from the vehicle body surface.

      3. Wipe off any tape adhesive residue with cleaner.

    2. Install a new window frame moulding.


      1. Using a heat light, heat a new window frame moulding and the vehicle body surface.

      2. Remove the peeling paper from the face of the window frame moulding.

        Tech Tips

        After removing the peeling paper, keep the exposed adhesive free from foreign matter.

      3. A01EOX4E02

        Attach the clip and double-sided tape to install the window frame moulding.

        Tech Tips

        Press the window frame moulding firmly to install it.

  2. INSTALL FRONT DOOR BELT MOULDING ASSEMBLY LH

    A01EO7V

    1. Attach the claw to install the belt moulding.

  3. INSTALL FRONT DOOR GLASS RUN LH


    1. Install the front door glass run LH.

  4. INSTALL FRONT DOOR GLASS SUB-ASSEMBLY LH


    1. A01EOQ4

      Insert the front door glass sub-assembly LH into the door panel along the glass run as indicated by the arrows in the illustration.

      Note

      Be careful not to damage the glass.

    2. Install the front door glass sub-assembly LH to the front door window regulator sub-assembly LH with the 2 bolts.

      Torque:
      8.0 N*m  { 82 kgf*cm, 71 in.*lbf }

  5. INSTALL FRONT DOOR SERVICE HOLE COVER LH


    1. A01EQVU

      Apply butyl tape to the door.

    2. Pass the front door lock remote control cable assembly LH and front door inside locking cable assembly LH through a new front door service hole cover LH.

      Note


      • When installing the front door service hole cover LH, pull the links and connectors through the front door service hole cover LH.

      • There should be no wrinkles or folds after installing the front door service hole cover LH.

      • After installing the front door service hole cover LH, check the sealing quality.

    3. A01EMWJE01

      Connect the 2 connectors.

    4. Attach the 7 clamps.

    5. Install the bolt as shown in the illustration.

      Torque:
      8.4 N*m  { 86 kgf*cm, 74 in.*lbf }

  6. INSTALL OUTER REAR VIEW MIRROR ASSEMBLY LH

    A01ERRFE02

    1. Attach the claw to install the mirror.

    2. Install the 3 nuts.

      Torque:
      8.0 N*m  { 82 kgf*cm, 71 in.*lbf }

    3. Attach the clamp.

    4. Connect the connector.

  7. INSTALL DOOR TRIM COVER LH


    1. Attach the 7 clips to install the door trim cover LH.

  8. INSTALL FRONT DOOR PANEL CUSHION


    1. Install the front No. 1 door stiffener cushion with the screw.

  9. INSTALL FRONT INNER DOOR GLASS WEATHERSTRIP LH


    1. A01EPGL

      Attach the 4 claws to install the front inner door glass weatherstrip LH.

  10. INSTALL FRONT DOOR TRIM BOARD SUB-ASSEMBLY LH


    1. Connect the connector.

    2. A01EO3L

      Connect the front door lock remote control cable assembly LH and front door inside locking cable assembly LH to the front door inside handle sub-assembly LH.

    3. A01EMZN

      Attach the 4 claws and 14 clips to install the front door trim board sub-assembly LH.

    4. Install the 2 screws.

  11. INSTALL FRONT UPPER ARMREST BASE PANEL LH


    1. Connect the connector.

    2. Attach the 5 claws to install the front upper armrest base panel LH.

  12. INSTALL FRONT DOOR INSIDE HANDLE BEZEL PLUG LH


    1. Attach the 3 claws to install the front door inside handle bezel plug LH.

  13. INSTALL FRONT LOWER DOOR FRAME BRACKET GARNISH LH


    1. Attach the clip and claw to install the front lower door frame bracket garnish LH.

  14. CONNECT CABLE TO NEGATIVE BATTERY TERMINAL

    Note

    When disconnecting the cable, some systems need to be initialized after the cable is reconnected Click here.

  15. INSTALL ENGINE ROOM SIDE COVER LH


    1. Install the engine room side cover LH with the 7 clips.