DUCT TEMPERATURE SENSOR REMOVAL

Tech Tips


  • Use the same procedures for LHD and RHD vehicles.

  • The procedures listed below are for LHD vehicles.


  1. REMOVE ENGINE ROOM SIDE COVER LH


    1. Remove the 7 clips and engine room side cover LH.

      A01EN5SE01

  2. DISCONNECT CABLE FROM NEGATIVE BATTERY TERMINAL

    CAUTION:

    Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to disable the SRS system.

    Note

    When disconnecting the cable, some systems need to be initialized after the cable is reconnected Click here.

  3. REMOVE REAR NO. 1 SEAT ASSEMBLY LH

    Click here

  4. REMOVE REAR NO. 1 SEAT ASSEMBLY RH

    Click here

  5. REMOVE REAR NO. 2 SEAT ASSEMBLY LH

    Click here

  6. REMOVE REAR NO. 2 SEAT ASSEMBLY RH

    Click here

  7. REMOVE REAR STEP COVER

    Tech Tips

    Use the same procedure to remove the step cover on the other side.


    1. A01EQ9D

      w/o Illumination Type Front Door Scuff Plate:

      Detach the 2 claws and remove the step cover.

    2. A01EQ94

      w/ Illumination Type Front Door Scuff Plate:

      Detach the 4 claws and remove the step cover.

  8. REMOVE REAR DOOR SCUFF PLATE LH

    A01EN6Q

    1. w/o Illumination Type Front Door Scuff Plate:

      Remove the rear door scuff plate.


      1. Remove the screw.

      2. Detach the 3 claws and 4 clips, and remove the scuff plate.

    2. A01ERAD

      w/ Illumination Type Front Door Scuff Plate:

      Remove the rear door scuff plate.


      1. Remove the screw.

      2. Detach the 3 claws and 4 clips, and remove the scuff plate.

  9. REMOVE REAR DOOR SCUFF PLATE RH

    Tech Tips

    Use the same procedures described for the LH side.

  10. REMOVE REAR FLOOR MAT REAR SUPPORT PLATE

    A01EQA6

    1. Detach the 6 clips and 4 claws, and remove the support plate.

  11. REMOVE FRONT QUARTER TRIM PANEL ASSEMBLY LH

    A01ERFB

    Tech Tips

    When removing the front quarter trim panel, operate the reclining adjuster release handle and move the No. 1 rear seat to the position shown in the illustration.


    1. A01ESN6

      Detach the 3 claws and remove the cover.

    2. A01EOE1

      Remove the bolt and rear No. 1 seat belt anchor.

    3. A01EQO3

      Remove the bolt and rear No. 2 seat belt anchor.

    4. Remove the clip.

    5. Detach the 19 clips and 2 claws.

    6. Disconnect the thermistor connector and then remove the quarter trim panel.

      A01ENWJ

  12. REMOVE FRONT QUARTER TRIM PANEL ASSEMBLY RH

    Tech Tips

    Use the same procedures described for the LH side.

  13. REMOVE REAR NO. 1 SEAT PROTECTOR

    A01EOBFE01

    1. Detach the 10 claws and remove the 2 seat protectors.

  14. REMOVE REAR NO. 2 SEAT PROTECTOR

    A01EMYNE01

    1. Detach the 10 claws and remove the 2 seat protectors.

  15. REMOVE FRONT FLOOR CARPET ASSEMBLY

    A01EPWL

    1. Remove the 2 clips.

    2. Fold back the floor carpet.

      Tech Tips

      Fold back the carpet until it is possible to remove the rear No. 6 air duct.

  16. REMOVE REAR NO. 6 AIR DUCT


    1. Disconnect the 2 connectors.

    2. Remove the 5 screws and duct.

      A01ENHJ

  17. REMOVE DUCT TEMPERATURE SENSOR


    1. Detach the 4 claws and remove the 2 sensors.

      A01EMWI