REAR EVAPORATOR TEMPERATURE SENSOR REASSEMBLY


  1. INSTALL REAR EVAPORATOR TEMPERATURE SENSOR

    A01EMU8

    1. Attach the 2 claws to install the sensor.

  2. INSTALL EVAPORATOR SUB-ASSEMBLY

    A01ER66

    1. Sufficiently apply compressor oil to 2 new O-rings and the fitting surface of the hose joint.

      Compressor oil
      ND-OIL 8 or equivalent

    2. Install the 2 O-rings to the evaporator.

    3. Install the evaporator.

    4. A01EROL

      Install the rear cooling unit case LH with the 12 screws.

  3. INSTALL BLOWER MOTOR CONTROL

    A01EPO0

    1. Install the blower motor control with the 2 screws.

    2. Connect the connector.

  4. INSTALL BLOWER WITH FAN (REAR) MOTOR SUB-ASSEMBLY

    A01ERLF

    1. Install the blower motor with the 3 screws.

    2. Connect the connector.

  5. INSTALL HEATER RADIATOR UNIT SUB-ASSEMBLY

    A01EN6C

    1. Install the heater radiator unit to the rear cooling unit.

    2. A01ERX1

      Install the heater clamp with the screw and attach the claw.

  6. INSTALL REAR COOLING UNIT EXPANSION VALVE

    A01ENKE

    1. Using a 4 mm hexagon wrench, install the expansion valve with the 2 hexagon bolts.

      Torque:
      3.5 N*m  { 36 kgf*cm, 31 in.*lbf }

    2. Attach the clamp.

    3. Connect the connector.

  7. INSTALL AIR CONDITIONER ACCESSORY ASSEMBLY

    A01EQ8W

    1. Sufficiently apply compressor oil to 2 new O-rings and the fitting surface of the hose joint.

      Compressor oil
      ND-OIL 8 or equivalent

    2. Install the 2 O-rings to the air conditioner accessory assembly.

    3. Install the air conditioner accessory assembly.

    4. Using pliers, grip the claws of the clips and slide the 2 clips.

      Torque:
      5.4 N*m  { 55 kgf*cm, 48 in.*lbf }

    5. Install the bolt and 4 screws.

    6. A01EPG7

      Install packing as shown in the illustration.

  8. INSTALL REAR MODE DAMPER SERVO SUB-ASSEMBLY

    A01ENN2E01

    1. Align the damper servo as shown in the illustration, and install it with the 2 screws.

    2. Connect the connector.

    3. A01EODN

      Install the plate cover with the 2 screws.

  9. INSTALL NO. 2 AIR MIX DAMPER SERVO SUB-ASSEMBLY

    A01EQ67E01

    1. Align the damper servo as shown in the illustration, and install it with the 2 screws.

    2. Connect the connector.

  10. INSTALL REAR AIR MIX DAMPER SERVO SUB-ASSEMBLY

    A01ESEEE01

    1. Align the damper servo as shown in the illustration, and install it with the 2 screws.

    2. Connect the connector.

  11. INSTALL DRAIN COOLER HOSE

    A01EQ1N

    1. Attach the claw to install the drain hose.

    2. Install the screw.

  12. INSTALL REAR SIDE NO. 3 AIR DUCT

    A01ENPO

    1. Install the duct with the 2 screws.

      Torque:
      5.4 N*m  { 55 kgf*cm, 48 in.*lbf }

  13. INSTALL REAR SIDE NO. 2 AIR DUCT

    A01EQHC

    1. Install the duct with the 3 screws.

      Torque:
      5.4 N*m  { 55 kgf*cm, 48 in.*lbf }