REAR NO. 1 SEAT OUTER BELT ASSEMBLY INSTALLATION

Tech Tips


  • Use the same procedures for the LH side and RH side.

  • The procedures listed below are for the LH side.

  • A bolt without a torque specification is shown in the standard bolt chart Click here.


  1. INSTALL REAR SHOULDER BELT ANCHOR PLATE SUB-ASSEMBLY

    A01EOQDE01

    1. Align the anchor plate positioning hole with the claw, and install the anchor plate with the 2 bolts.

      Tech Tips

      First install the lower bolt, and then install the upper bolt.

      Torque:
      42 N*m  { 428 kgf*cm, 31 ft.*lbf }

  2. INSTALL REAR NO. 1 SEAT OUTER BELT ASSEMBLY

    A01ESNGE01

    Note

    When installing the retractor, make sure the claws of the vehicle (labeled "a" in the illustration) only contact the installation areas of the retractor.


    1. Align the claws with the seat belt positioning holes and install the retractor of the seat belt as shown in the illustration.

    2. Install the seat belt with the 2 bolts.

      Tech Tips

      First install bolt A, and then install bolt B.

      Torque:
      for bolt A
      8.5 N*m  { 87 kgf*cm, 75 in.*lbf }
      for bolt B
      42 N*m  { 428 kgf*cm, 31 ft.*lbf }
    3. A01EPNT

      Connect the pretensioner connector, as shown in the illustration.

    4. A01ER42

      Install the seat belt shoulder anchor with the nut.

      Torque:
      42 N*m  { 428 kgf*cm, 31 ft.*lbf }

  3. INSTALL REAR FRONT QUARTER TRIM GARNISH

    A01ES5Y

    1. Pass the seat belt anchor through the quarter trim garnish.

    2. Attach the clip and 2 guides to install the quarter trim garnish.

    3. Install the screw.

  4. INSTALL FRONT QUARTER TRIM PANEL ASSEMBLY

    A01ERFB

    Tech Tips

    When installing the front quarter trim panel, operate the reclining adjuster release handle and move the No. 1 rear seat to the position shown in the illustration.


    1. w/ Manual Folding-up Function:


      1. Connect the thermistor connector, power outlet socket connector and rear seat lock control lever cable.

      2. Attach the 19 clips and 2 claws to install the quarter trim panel.

      3. Install the screw, clip and bolt.

        Torque:
        for bolt
        12 N*m  { 122 kgf*cm, 9 ft.*lbf }
        A01EPEA

    2. w/ Automatic Folding-up Function:


      1. Connect the thermistor connector and power outlet socket connector.

      2. Attach the 18 clips and 2 claws to install the quarter trim panel.

      3. Install the screw and clip.

        A01ENWJ
    3. A01EQO3E01

      for LH side:


      1. Install the rear No. 2 seat belt anchor LH with the bolt.

        Torque:
        42 N*m  { 428 kgf*cm, 31 ft.*lbf }

        Note

        Do not overlap the anchor part of the seat belt and protruding parts of the vehicle body.

    4. A01EQD8

      for RH side:


      1. Install the rear No. 2 seat belt anchor with the bolt.

        Torque:
        42 N*m  { 428 kgf*cm, 31 ft.*lbf }
      2. A01ES5O

        Attach the 3 claws to install the cover.

    5. A01EOE1

      Install the rear No. 1 seat belt anchor with the bolt.

      Torque:
      42 N*m  { 428 kgf*cm, 31 ft.*lbf }
    6. A01ESN6

      Attach the 3 claws to install the cover.

  5. INSTALL REAR DOOR SCUFF PLATE

    A01EN6Q

    1. w/o Illumination Type Front Door Scuff Plate:


      1. Attach the 3 claws and 4 clips to install the scuff plate.

      2. Install the screw.

    2. A01ERAD

      w/ Illumination Type Front Door Scuff Plate:


      1. Attach the 3 claws and 4 clips to install the scuff plate.

      2. Install the screw.

  6. INSTALL REAR STEP COVER

    Tech Tips

    Use the same procedure to install the step cover on the other side.


    1. A01EQ9D

      w/o Illumination Type Front Door Scuff Plate:

      Attach the 2 claws to install the step cover.

    2. A01EQ94

      w/ Illumination Type Front Door Scuff Plate:

      Attach the 4 claws to install the step cover.

  7. INSTALL REAR FLOOR MAT REAR SUPPORT PLATE

    A01EQA6

    1. Attach the 6 clips and 4 claws to install the support plate.

  8. INSTALL REAR NO. 2 SEAT ASSEMBLY


    1. Install the rear No. 2 seat assembly Click here.

  9. CONNECT CABLE TO NEGATIVE BATTERY TERMINAL

    Note

    When disconnecting the cable, some systems need to be initialized after the cable is reconnected Click here.

  10. CHECK SRS WARNING LIGHT


    1. Check the SRS warning light Click here.